Xpulse 4V 200 | Maddog ScoutX Aux Lights | Project 83X Headlamp Grill | BOBO Charger Installation

[@microrao]

Although some parts of the wiring are unclear, this is by far the BEST video on installation of fog lights.

[@omkarbordavekar4098]

Thank you. Today I have installed maddog scout x by my own. Only due to your video. Thanks for giving confidence. So happy after seeing results. N learnt many more things.

[@motovin77]

That's awesome, fantastic job 🤩

[@naiduvinay4911]

"If you loose the speedometer, you can't see your speed" 👍

[@motovin77]

Little humour 😂

[@automotriztechnica]

Yes, he stated that 😀

[@VibhorWase]

It looks even more badass now

[@automotriztechnica]

It looks more beautiful than before 😀👍

[@brijeshparmar7460]

Bro.. R u the engineer who has designed the hero xpluse.. I am wondering how u know abt the entire installation

[@motovin77]

Hahahahaha no brother i didn't design the Xpulse 😀 it's just a simple electric circuit, once you study it, it's quite simple.

[@brijeshparmar7460]

@@motovin77 I like you videos about the xpluse 200 as I am planning to buy it. I am impressed with you cause you do lot of things at your own. So i request you to keep inspiring upcoming owners like me and provide the insight about Xpluse. With regard to study of installation, if there is any guide or video do let me know.

[@motovin77]

@@brijeshparmar7460 Thanks 🙏😊

[@avinashgowda8932]

I am into xpulse family now, yesterday I bought xpulse 200 4v, even I nees to install aux light. Looks simple but u have an great idea of it

[@motovin77]

@@avinashgowda8932 Congratulations 👍

[@jsyn_p]

Very good video. Probably one of the most comprehensive videos on YT. I have a query though. Do we need to ground the black wire of the harness or does it go directly into the negative terminal of the battery.

[@rehnanehal2199]

We can go for both ..even u can ground it or u can go for battery terminal

[@ArnabMurshidabadi]

Hello sir... One question I have. To install the clamps, you need to work with the screws that are holding the forks. Is it okay to do so?

[@motovin77]

Yes sir that is correct and it's completely safe, just ensure to tighten the bolts back as they were before

[@ArnabMurshidabadi]

@@motovin77 Thank you sir. 👍🏽 Actually I have ScoutX installed on the engine guard, but that location absorbs some amount of illumination. So I thought about installing it on the handlebar but was considering not to hamper any factory fittings. I decided the place to be just below the indicators using the Maddog Fork Clamp (Rs-1699), but I doubt it'll touch the tank when the handlebar is turned to the maximum. So I think I'll have to do what you've done.

[@kkhaanabadoshh]

Is it legal to put 40W Aux lights in this bike? I remember you went for Scout Aux for Highness as its illegal to intall Aux lights with higher wattage than the stock headlight.

[@OFFRoader-z9g]

Sir what if the fuel is there inside tank? How to remove

[@nitinhadale1519]

Is this the most versatile and value for money bike ? City Highway Off road

[@motovin77]

Absolutely it is and there is no competition at this price point... Lowest cost of purchase and maintenance...

[@rameshkumar8965]

Thanks, Very nicely narrated, can i use wire from horn to trigger relay? Anyways horn works only after ignition is on. Or Can I tap a wire from low beam light and use that to trigger relay, so Auxiliary lights work only when engine starts?

[@Saikat_Palit]

You installed Scout, and non pro switch and harness in your cb350. Any reason why you switched to pro switch and harness? Are the non pro ones not suitable during rain? Also for fast night riding (80+) is Scout enough in cb350?

[@Chamba_nivasi]

You seem to be an engineer. After installing a pair of HJG LED aux lamps of 40 Watt, 4000 lumens each, the battery drains within an hour so much so that once stopped, the bike won't start. Even jerk-start and kick-start won't work on my Xpulse2004v. How about connecting to alternator instead of the battery?

[@motovin77]

I didn't have any issue after installing 20+20w maddog lights. Since the battery is part of the alternator circuit, it will pull current from the battery unless you figure out a setup to completely isolate the battery from the aux lights circuit.

[@rahul_rathva_]

Sir Love from gujarat!....kya garaj se Bina wires cut Kiye fog light lagvane se warranty rahti hai ya nahi ?

[@motovin77]

Thanks Bhai 👍 yes if no original wire is cut, warranty is intact.

[@ujjwal94roy]

Thanks for making it simple.....

[@MountainsMoto]

Thanks, i also bought the Scout lights for my Xpulse. Can you tell me while pulling out all tank tubes, will it also spill the fuel ?

[@motovin77]

Not really, but a few drops might which isn't an issue.

[@abhinavkashyap2000]

Hi, I liked this video as you were quite thorough with installation steps. I own a hero Xpulse BS6 but am hesitant in installing aux lights. As per Hero service center that might void the bike's warrenty. Did you confirm this with Hero ?

[@motovin77]

Thanks 😊🙏 warranty will not be void as none of the original wiring was cut or tampered.

[@abhinavkashyap2000]

@@motovin77 Thanks a lot for sharing :)

[@rajatghosh]

show room claim says xpulse battery too weak to handle extra lights, do u have any idea on this ? or feedback ?

[@motovin77]

No idea sir, i use the lights mostly on highway for night rides only.

[@vinaypanchal1692]

Hey, Vinay is ther any leakage of fuel while removing the fuel tank?. I want to install the same with my xpulse can you plz help.

[@motovin77]

Yes few drops of fuel will leak when you disconnect the fuel line to take off the tank. That should not be an issue.

[@vinaypanchal1692]

@@motovin77 that's pretty much ok. My concern is there any continuous flow of petrol from the tank. If the tank was full. Btw thanks for your reply and support.

[@ashutoshranjan131]

i have booked the same colour xpulse , can you tell me whats the price of Aux Light with installation charges ? , also will it affect warranty ?

[@motovin77]

Congratulations 👍 Lights costed me about 8000 and installation is self.. should not affect warranty as it's a seperate wiring harness

[@ujjwal94roy]

Can we use similar thing to connect bobo mobile holder/charger with ignition ? Since you connected your directly to battery.

[@motovin77]

Yes

[@BD-vg5gg]

Sir i have one dout here.. regarding the actual switch for the scouts.. do we have a connector in the harness itself for the switch to plug in??

[@motovin77]

Yes, it's plug and play

[@harishk9720]

Person with white tshirt is your brother? I like your Tshirts bro where did you buy them?

[@masacheku]

Very useful! Subscribed :)

[@motovin77]

🙏

[@MSN_MOTO]

Excellent job

[@TusharWalwaikar]

Can we connect the bobo charger without wire cutting to the ignition ???

[@motovin77]

Yes, connect to the same wire where i connected the trigger wire of ScoutX wiring.

[@bilbobaggins3747]

Wow man great

[@tuntunewala]

Will you change your xpulse's exhaust or not I also want to change it? But doesn't want to drop it's mileage

[@motovin77]

Not really at this point.

[@rahulgajinkar6084]

Any rusting issues in this bike

[@motovin77]

Got it 2 weeks ago, nothing so far...

[@hariharan8573]

When did you book your 4V?

[@rahulgajinkar6084]

What about material quality in this bike

[@motovin77]

Much more improvement quality, refinement, fit and finish....

[@kiru4258]

Good question

[@AshieshDutta]

Where is your cb350 bro...

[@thomaskamei4268]

👍👍👍

[@bittugeorge1158]

Where is Honda hness

[@motovin77]

With my cousin

[@AltafHussain-sr6rn]

You removed the whole fuel tank, speedometer to install a aux light ?!! even that ignition connection seems like shit....Now the whole bike will rattle like a mf on bad roads. Even a stock new xpulse rattles on gravel.

[@motovin77]

@@AltafHussain-sr6rn I never had any rattling before not after installation of lights. My bike runs like a dream. Please get your bike checked at service center.