Yakima OverHaul HD Adjustable Truck Bed Rack

[@Pescador2022]

I went with the 60 inch bars on my full-size truck as well. The 68 were too long and looked funny. Yakima is a good looking and functional product. 👍nice truck

[@JFelix602]

how easy is it to adjust the height ?

[@coder6083]

Great video. I have a 2023 F-150 and the Yakima site says the 60" won't fit my application and the 68" is the smallest I can get? Just wanted to verify you stated the sizing correctly. thanks.

[@PatriotDIY]

I have the 60in on my truck!

[@coder6083]

@@PatriotDIY thanks!

[@coder6083]

@@PatriotDIY did you purchase through Amazon? I can't order the 60" from the manufactures website with my vehicle information uploaded.

[@SANPEDROCUSTOM]

Now I was thinking of doing the same thing but I have a long bed which I wanted to keep my weather guard tool box and ad a retract cover right up to the tool box. Is the bed going to have leaks where the cover butts up against your tool box? For me it wouldn't be a problem because I have a Deck drawer system in the truck bed already. Thanks

[@joshstone6934]

have you tried that? I have the same setup and not sure I want to give up the weather guard tool box.

[@MrDmason57]

At 6:10 during the installation your t-bolts were inserting in a long flat backing plate that slid into the t-track. Did those 4 backing plates come with the kit? The Yakama website does not show those plates.

[@PatriotDIY]

Yes, those are included

[@JonMThorpe]

Any idea of Yakima sells those backing plates separately?

[@JonMThorpe]

@@PatriotDIY are the flat bars listed in the instructions with a part number or name?

[@PatriotDIY]

@@MrDmason57 yes

[@ChenzosWorld]

All I wanna know is what hardware is compatible with the T track and no one mentions it anywhere. Please help. I don’t want to order from Yakima

[@sharkdm01]

I’ve had my racks for a while and I actually use them. In some places the paint is coming off. Can you paint right over that or is there something to do minor corrections?

[@bizomatic]

Can the height be adjusted with the cross bars installed? Or is it a set and forget system?

[@PatriotDIY]

@@bizomatic you need to loosen the crossbar before adjusting the height, then resecure them

[@Nate-zy5ce]

Do you know if that American Work Cover keeps water out as well as the Diamondback HD cover? I love that with this one you can open it for even more room beneath whatever goes on top of the rack, something you cannot do with the Diamondback HD.

[@PatriotDIY]

I don't know about the diamondback, but I can tell you I've been through carwashes and thunderstorms with 0 water getting in!

[@markmcadams]

Thanks for the video. Do you know if this sliding cover works with a 2020 Honda Ridgeline? Do you have a link for the cover to make sure it is compatible for both our truck and the Yakima system?

[@PatriotDIY]

@@markmcadams links in the description

[@austinmcfadden5470]

Can the top bars be easily removed if I need to move a refrigerator?

[@PatriotDIY]

@austinmcfadden5470 yes, just 8 bolts to remove the top bars. In fact you can remove the entire rack with just 8 bolts.

[@Nate-zy5ce]

Can those sidebars on each side be easily and quickly removed and later added back, without causing damage if done often over time? If so, I imagine it would be great b/c I could leave them off most of the time so I can still open the Diamondback HD cover on either end, but put the sidebar back when I specifically need it. Also, do you have any experience or knowledge how much the average mpg of you vehicle might decrease if you mounted and drove with a pop up hardcover tent like say the Roofness Sparrow on top? I ask b/c it would clearly lay above the height of the cab roof. Thanks.

[@PatriotDIY]

Only 4 screws holding the side bar in place!

[@xlr8r17]

The plates the bolts go in on the towers look new. I don't think the older rail system had the metal plates the bolts slide in with, which used to cause bent rails.

[@PatriotDIY]

Yea, they fixed that problem a while back

[@JonMThorpe]

Do you know if the flat bars can be bought separately?

[@realexc89]

I have a 6.5 bed f150 how you much does the toolbox reduce the space I'm thinking about that one or the jr. size but the toolbox is not deep is only like 4"

[@PatriotDIY]

@@realexc89 this tool box take 20"

[@jamesrichter9974]

What is the space in the cover box area

[@PatriotDIY]

The toolbox is 20" so the cover would be the length of your bed minus the toolbox if that answers your question

[@jamesrichter9974]

I was trying to get how much space is under the cover storage box in the bed

[@PatriotDIY]

@@jamesrichter9974 it rides pretty much in line with the rails of the truck bed so you don't loose any height there

[@jamesrichter9974]

@@PatriotDIY I was talking about under the canister and toolbox area it’s 20 inches but I’m looking for the space between the bed floor and the bottom of the tool box

[@alexanderaguillermo3144]

How good does your truck look, tell me can you wash it in a car wash with the rack

[@fleedermouse]

Moons awesome but that’s a crazy amount to spend on a tonneau cover

[@lintelle2382]

as beefy as it looks, the 500 pound weight limit is pretty, uh, limiting...

[@NoCoverCharge]

$5 grand for a tonneau cover that’s a no bueno