Follow along as we disassemble our Yamaha Blaster engine down. We start we a fully assembled engine and end with a split case. Thanks for watching and as always please send us any questions that you have.
Пікірлер: 52
@scottbell834 жыл бұрын
I've watched about 10 or so videos and yours is the best it's the most comprehensive and easy to learn thanks
@jeremylong62296 жыл бұрын
thanks for vid have to split mine cause i had a little bit of a piston breakage and now ill know exactly how to do it.
@lh21972 жыл бұрын
Thanks
@jello36616 жыл бұрын
ah the sandwhich bags *LIFE SAVERSSSS*
@grindinggearsgarage95786 жыл бұрын
always have a bag and a sharpie on hand
@bryanroupe86465 жыл бұрын
Hey man do you have a link for the adjustable hone you used ? Previously I just used a ball hone until I got what I was looking for. If you haven't used a ball hone they are awesome but, not nessassarily for precision accuracy. But, if you do alot of honing to clean cylinder wall's its so much better than a stone tool, which is what I used for years.
@2183valerio4 жыл бұрын
did you have compression prior to removing the top end.
@MitchsTechInsight7 жыл бұрын
I have a 2003 blaster that I have taken apart with the correct tools, but the counter balancer gear is stuck on and won't come off, I've tried wd40, I tried rocking it back and forth, it just won't budge, I'll try and inbox u a picture of what I'm looking at, any help would be appreciated
@brokebikemtb44487 жыл бұрын
hey man new sub here....content is great ...i have a question....its about a 2001 yamaha warrior....i just pulled the top end off and my valves need attention...mainly lapping and vg seals.... I know how to lap them but what the manual said to do is pour a solvent into the port and check for leaks ...i have leakage....so do think I should lap the stock ones or buy new and lap those in...im trying to save money cuz this rebuild is adding up but I don't want to cut critical corners either
@grindinggearsgarage95787 жыл бұрын
id try to lap the stock ones. worst thing that is gonna happen is a little wasted time.
@xxcristiangxx71573 жыл бұрын
a question When you remove the piston from the connecting rod, you look at the crankshaft in that compartment, it has oil or there is no oil there
@geoaponte92347 жыл бұрын
At 12:20 can you split the case there without taking off the other side or do you have to take off the other side
@dill55006 жыл бұрын
This is an awsome video
@grindinggearsgarage95786 жыл бұрын
thanks for watching!
@TEAMCREAM_966 жыл бұрын
Bought a blaster and they've been running it on straight gas with the oil pump blocked off , it still ran but there is a hole in the case so it smokes like a train
@getttittttganggarage8196 жыл бұрын
Blasters are 2 strokes
@dominator23548 жыл бұрын
you definitely know what you're doing!
@grindinggearsgarage95788 жыл бұрын
Thanks man! Don't forget to subscribe!!
@dominator23548 жыл бұрын
+Grinding Gears Garage already did! I'm planning on buying a 2001 yamaha blaster in January... will they be hard to find then?
@grindinggearsgarage95788 жыл бұрын
+Dominator 235 blasters are everywhere. They are all the same from 88-2002 and 2003-2006 they made a few changes like hyrdaulic brakes and electrical changes
@dominator23548 жыл бұрын
+Grinding Gears Garage how much do you think I can buy one for?
@grindinggearsgarage95788 жыл бұрын
+Dominator 235 all depends they vary by area. You should be ok at under 1000. Also check out our new Facebook page facebook.com/grindinggearsgarage1
@Kyle_gallegher3 жыл бұрын
Do you insist on resurfacing the cases or whatever its called or can I get away with yama bond or similar on my lt250 and blaster rebuilds?
@prestonnoble7 жыл бұрын
HI, love the video! At 12:20 on your video you said ignore this next part if you are splitting the case. I bought a new crank cuz my main connecting rod bearing is shot, so do i need to disassemble the whole clutch side? just to get the old crank out and new one in?
@grindinggearsgarage95787 жыл бұрын
your going to need to take apart a few things on the other side of the case to remove the old crank
@4DoeBoy4 жыл бұрын
Grinding Gears Garage sooo the only ones you would have to take off is the clutch and main gears where the timing is????
@iggmoneysoles46065 жыл бұрын
I have a stripped bolt and it’s the last bolt to remove the cylinder I can’t get it off any help on removing a stripped bolt any help is useful ty in advance ?
@Kyle_gallegher3 жыл бұрын
Did u get it? Or sell the quad
@DeanErickson1138 жыл бұрын
Man clean that engine up before you start.
@grindinggearsgarage95788 жыл бұрын
i dissaembled the engine for a full rebuild scrubbed it down
@mikelwmc7 жыл бұрын
Grinding Gears Garage do you also disassemble the trans gears to clean? hate to get dirt and mud in there.
@dominator23548 жыл бұрын
hi, when you rebuild a blaster engine, do you have to let it run idling for a certain amount of time? how long?
@grindinggearsgarage95788 жыл бұрын
+Dominator 235 there is a specific break in procedure. if you google breaking in a 2 stroke engine. need to do a few heat cycles then ride around on a tank of gas lightly
@charleswatson5086 жыл бұрын
What could cause your ur kicker to stick
@luischavez32477 жыл бұрын
hey how's it going I just bought a 2009 Yamaha Blaster and I'm having an issue that when you take off on first gear it struggles to go I want to you can out Thanks
@grindinggearsgarage95787 жыл бұрын
luis chavez have done a leak down test? 2 strokes usually are plagged by leaks causing them to run badly. Also since its a recent buy id do a comp test as well
@mackayham1946 жыл бұрын
Where did you get that flywheel puller at 10:10? Is a special tool from Yamaha or can I get it somewhere else?
@grindinggearsgarage95786 жыл бұрын
you can buy them all over. usually specific to each motor
@nincal6 жыл бұрын
Question why would the platic gear blow apart .??? and when the pomp is hooked up it does not ???... i had a few blasters in my time ...lol
@grindinggearsgarage95786 жыл бұрын
its just a known failure point. oil degrades plastic overtime. way easier to mix fuel then run the risk of the pump not working!!
@nincal6 жыл бұрын
True your right .... better to self Mix ..... had my share of top ENDS rebuild over the years!!
@lutviatussoleha65303 жыл бұрын
how much is the Yamaha Blaster spare parts there, friend
@PIKEBOYTV2 жыл бұрын
How can I contact u for work that needs to be done?
@christophermorel79238 жыл бұрын
Where are you located? I rather jus pay yu to work on it than me mess it up
@grindinggearsgarage95788 жыл бұрын
Located in South Eastern pa. I am super packed for space so it will be a while till I'm free
@DJswope733 жыл бұрын
@@grindinggearsgarage9578 where at? I'm located in Central pa
@dominator23548 жыл бұрын
did you upload a video of the assembly for the engine?
@grindinggearsgarage95788 жыл бұрын
+Dominator 235 we did a bottom end rebuild video. We are editing a top end rebuild currently. Thanks for watching
@dominator23548 жыл бұрын
+Grinding Gears Garage and what is a stator?
@grindinggearsgarage95788 жыл бұрын
+Dominator 235 stator is behind your flywheel. thats where you generate your spark and the electric to run your lights
@djmystery72357 жыл бұрын
Giant the stator also used for the ignition timing