Yamaha FJ09 Tracer Mods - LED Turn Signals and Removing Center Stand!

⭐Parts Used in this Video⭐
Sequential LED Turn Signals: amzn.to/3MpXlw8
Yamaha Pod Signal Adapters: amzn.to/3KiyCYx
Flasher Relay (Required for Use With LED's): amzn.to/3KiyCYx
Solder Seal Connectors: amzn.to/3HM0Mtc
Heat Shrink Wrap: amzn.to/3hXMOKF
Discounts!
✅JL Designs Fender Eliminator Kits and Taillights! : jld7.com/home
USE CODE "Motovice" at JL Designs for 10% Off!!
✅ Chin Mount! Chin Mount offers mounts for over 54 helmets!: chinmounts.com...
USE CODE "Motovice" for 10% off your entire order!
Yamaha FJ09 Tracer Mods - LED Turn Signals and Removing Center Stand! 3rd episode for the Yamaha FJ09 Tracer Mods and ton more mods on the way! Today, the Yamaha FJ09 Tracer gets led turn signals! No more do we have to see those hideous pumpkin lights. We also removed the center stand on the Yamaha FJ09 Tracer which will definitely save us some weight. I haven't seen any center stand removal videos, so I figured it would be good to film that. Besides the LED turn signal install and center stand removal, we did some small cosmetic changes as well. Many more mods for the Yamaha FJ09 Tracer on the way!
This bike is super similar to the Yamaha MT-09, Yamaha MT09, Yamaha FZ-09, Yamaha FZ09, Yamaha Tracer 900 and the Yamaha Tracer GT. A lot of the work that I am doing can be interchangeable to the Yamaha MT09, Yamaha FZ09 and Yamaha Tracer.
#fj09 #fj09tracer #yamahafj09 #tracer #yamahatracer mt09 yamaha fz09 yamaha mt tracer 900 tracergt

[@MotoViceOfficial]

I reply to all comments on my videos, so please support the channel by dropping a like, comment and subscribe for future content!

[@doughummel4215]

I bought the same flashers and also purchased the TST signal plug converters so I didn't have to cut any wires. Thanks so much for this informative how-to vid. Keep up the good work!

[@MotoViceOfficial]

Thank you! Yeah the TST converters are nice and easy. I’ve done a lot of little electrical stuff on bikes so I don’t mind messing with some wires 😂

[@2007s197]

Here I am at 2:45 am, installing parts and prepping for a 500-mile ride in 9 hours. Also you showed nothing regarding the relay and the link shows no relay. Thank you for the video o7

[@smurik1]

Why you didn’t use the blue wire for the running lights? Can you connect brown and blue together to red one? I would like to have a running lights also Thanks mate

[@theoau]

Good video. Your link to the flasher relay in the description is wrong. It links to the adapters.

[@twowheelsquirrel]

Did you not have to replace the flasher relay going from standard bulb to led?

[@raileanua1]

Looking good! Keep up the great content!

[@MotoViceOfficial]

Appreciate it!

[@drifter-indian1448]

Great video! Mind sharing the link to the Relay? The amazon link in the description doesn't work

[@jackmccafferty6501]

Yo so i have the same bike! and i got almost the same sequential blinkers from Oxford except they came with built in resistors. I installed the rear ones and they don't work how they should, theyre dim and dont sequence. I ordered the led relay which im sure will fix the problem. But i noticed yours dont have a built in resistor so im wondering if i can delete the resistor on the front cause theyre kinda bulky? Anyways great job on shooting this video! Camera angles very good and audio is very clear!

[@MotoViceOfficial]

Thank you! I put a lot of work into my videos to make they come out well! And yes you don’t need any resistors front and back if you have the relay installed under the seat.

[@sdrobot1910]

Awesome dude!! Do you have video to how you do the rear blinkers?

[@MotoViceOfficial]

That's so odd! I did them last night and didn't think to film it. Its the exact same process with using the stock harness connectors though and splicing in the connectors of the led signals.

[@sdrobot1910]

How did you integrate the stop light to the blinker?

[@MotoViceOfficial]

@@sdrobot1910 Are you talking about the hazards?

[@sdrobot1910]

@@MotoViceOfficial There are 3 wires coming out of the Rear Blinker. But the OEM blinkers only have 2 wires, so how did you connect the RED Wires to integrate to the stop light?

[@MotoViceOfficial]

@@sdrobot1910 well one is the license plate wire, other two would be the tail light positive and negative and then only 2 wires come out of each signal for the rear.

[@markadams5823]

Did you install a flasher relay?

[@MotoViceOfficial]

Yes relay is always necessary when moving from halogens to led’s.

[@miusrname1]

Do you not care about losing your running lights? I also bought LEDs and used the runner lead. For some reason both the running and blinker worked. But when I installed the rears, the fronts stopped working and got dim. Any ideas on how to retain both running and blinker?

[@MotoViceOfficial]

Nope, I always have my headlights going and never ride street unless on the way to a canyon. You would need to split three ways which they have: red, blue, black.

[@Ali-yh8dl]

Hi, awesome video. just have a question, do these turn signals require an LED relay to sync the blinking rate ? I'm getting a 2020 Tracer 900 GT and the pumpkin turn signals as you noted are really ugly :D

[@MotoViceOfficial]

Hi there. Yes it needs a relay which is linked in the description. After rendering the video, I realized I did not mention it and KZbin doesn't allow me to add anything in after uploading!

[@Ali-yh8dl]

@@MotoViceOfficial great, ill check it out. Thank you for your reply

[@markadams5823]

@@MotoViceOfficial I was a little late to the party you don't have to answer my question about the relay

[@wissamharb5684]

@@MotoViceOfficial i watched the video 3 times thinking that I kept missing the indicator relay part. Can you please explain how you installed that? Btw thank you so much for the video it's super helpful!!

[@markadams5823]

Nice shirt.

[@MotoViceOfficial]

Thank you!

[@brian623]

I have tracer 900 gt

[@grego10r]

Yeah they look nice but u can't see them out in the daylight and my diet after 1 year so waste of money and time

[@MotoViceOfficial]

Well if they die, I will get the TST BL6 ones. I wasnt trying to drop much money on this bike as I wont be riding it as much.

[@johnpreston6720]

when saying the word solder, why do you not pronounce the L?