Tap to unmute

Yamaha XT225 TTR230 Upgrade Cam Bearing to Ball Type

  Рет қаралды 29,631

alexkram

alexkram

Күн бұрын

Пікірлер: 79
@kevinsmith467
@kevinsmith467 4 жыл бұрын
I was reading another forum article on this rework and he was saying much the same, with similar experiences. He did say that of the various types of 6005 bearing available he went for the 6005ZZ. The metal sealed ones would stand the cylinder head temps whereas the rubber seals may not. He also suggested removing the metal shield from one side for bearing lubrication but to keep the outer seal in place. his reasoning was that it would prevent head oil draining away when parked on the side stand.
@aol11
@aol11 3 жыл бұрын
Worked great, The only thing I did different Was clean the grease from the bearings and replace it with engine assembly lube so the oil passages didn't get clogged with grease.
@jonganzer7478
@jonganzer7478 4 жыл бұрын
This is a REALLY useful video with all the bolt sizes and bearing information included. Thank you for taking time to put all this together, you've helped out a lot of people.
@alexkram
@alexkram 4 жыл бұрын
Thanks for that. I have used KZbin to learn how to do countless projects so I like to contribute where I can.
@Singh_1989
@Singh_1989 3 ай бұрын
Thanks for the information! Although I don't own one of these motorcycles, this engine is identical to the one in my Yamaha timberwolf. I had an issue with the cam bolt backing out and the gear fell of and tore up the end of the camshaft. In finding a new cam I found it shares a cam with this bike which I could get much cheaper. I also came across this video and considered the upgrade. When I removed the bushing off the old camshaft I found it had uneven wear, and that's what made me decide to find this video again and find the bearing you suggested. I can't wait to get these parts on order and get this fourwheeler up and running!
@ronbuellwinkler4586
@ronbuellwinkler4586 3 жыл бұрын
I did your mod to one of my bikes today. Took me about 2 hrs working slow. Plan to do the other tomorrow.
@allenscott1705
@allenscott1705 3 жыл бұрын
Incredible job and upgrade-well done man and thanks. You make what I wouldn't dream of doing look possible. A big thank you also for the wrong oil filters video.
@FreeRiderFMX
@FreeRiderFMX 4 жыл бұрын
I used the wrong oil filter on my wifes 230.... feel so stupid. Now researching engine stuff. Thanks for the video!
@alexkram
@alexkram 4 жыл бұрын
Hopefully you can fix it like I was able to, and it's an upgrade.
@FreeRiderFMX
@FreeRiderFMX 4 жыл бұрын
@@alexkram yea I like the bearing mod, how are the engines holding up?
@RYANINBODEN1547
@RYANINBODEN1547 Жыл бұрын
So the top end is pretty much identical to my Timberwolf 250 motor and i've been looking for a way to pull the camshaft out for maybe two weeks and I never considered using your method. Good idea frl really helped me out haha.
@ChaoticDetour
@ChaoticDetour 6 жыл бұрын
I had a family member drop off their very neglected XT225 last week. Only 13k on the motor, but not much works on the bike. Winter project for next years fun. Thanks for this video, I will have to consider this since I have to reseal the motor, leaks like a sieve.
@dannyhall2176
@dannyhall2176 6 жыл бұрын
Just did to two ttr230 worked great same bearing fit. Was surprised to see both aluminum bushings I removed had wear on them.
@baishalimarsinsuat9104
@baishalimarsinsuat9104 Жыл бұрын
what cam bearing did you use to your ttr 230f and size may i see your upgrade?
@metallurjix
@metallurjix 5 жыл бұрын
Nice one, Alex. Just wasted an hour trying to pull out the darn cam without a puller. The way the cam was flopping around in there, I'm pretty sure the cam journals are toast.
@Rusty-Hinge
@Rusty-Hinge 2 жыл бұрын
Interesting mod. Can I ask how the new bearing held up over time?
@volodymyr3322
@volodymyr3322 5 жыл бұрын
Great video man. Thanks. This weekend i will do the same.
@waldemirsouza9842
@waldemirsouza9842 3 жыл бұрын
Bom dia, estamos colocando rolamentos nas duas pontas desse eixo, melhora o desempenho e acaba com o barulho
@leandrolautharte4112
@leandrolautharte4112 3 жыл бұрын
Buen día, tuviste que hacer un desgaste en el extremo interno para poner un rodamiento allí adentro también ? O que número de rodamiento usaste para que entre ?
@ramiroalvescoutinhoneto8865
@ramiroalvescoutinhoneto8865 3 жыл бұрын
Fiz na minha XT 225 por ocasião de uma troca de embreagem. Pedi para colocar rolamento nós dois lados
@matiaskarinleiva8012
@matiaskarinleiva8012 5 жыл бұрын
Muy bueno lo voy a probar soy de Argentina. No influye con el flujo de aceite?
@leandrolautharte4112
@leandrolautharte4112 3 жыл бұрын
Buenas estimado, lo hiciste ? Soy de Argentina y pienso que debería hacerlo
@motophoenix5951
@motophoenix5951 4 жыл бұрын
That new ball race went in a little too easily for my liking. I think I would have used some Loctite Bearing fit just to make sure the bearing didn’t start creeping when in use. Nevertheless, great video, thanks for sharing.
@Grampadude
@Grampadude 3 ай бұрын
I think you would want TDC on the compression stroke? I’m thinking an unsealed bearing would be best. There would still be residual oil in the bottom portion of the outer race when shut off?
@Andr..
@Andr.. 5 жыл бұрын
Отличная идея!! Привет из СССР
@earlebaker2440
@earlebaker2440 4 ай бұрын
Does enough oil fly around to lube the bearing?
@charlespratt8663
@charlespratt8663 4 жыл бұрын
Very informative video. I just wonder if the aluminum bushing was designed in part to direct the oil flow where needed vs the bearing which may starve parts for oil?
@alexkram
@alexkram 4 жыл бұрын
There is an oil supply hole in the cam that supplies oil to the bushing. The bearing covers up that hole, which forces that oil to other areas like the other bearing and the cam lobes. That is the way I was thinking anyway. I have since sold this bike but it ran fine for 1000 miles before I did.
@charlespratt8663
@charlespratt8663 4 жыл бұрын
@@alexkram I appreciate the follow up!
@charliesybert2683
@charliesybert2683 Жыл бұрын
Did it hold up well?
@ronbuellwinkler4586
@ronbuellwinkler4586 3 жыл бұрын
I just found this... excellent. thx
@blairguinea1337
@blairguinea1337 4 жыл бұрын
Great job Alex
@brandonrose3627
@brandonrose3627 2 жыл бұрын
Did the bearing last? I got a moto 4 with the cam bushing worn out was thinking about using the bearing just like to know if it would last a while before I do replace it with a bearing.thanks.
@oregonskate
@oregonskate Жыл бұрын
I can not even press down both rocker arms without a pry bar. Any suggestions? camshaft seized, replaced it, both times can not push them down.
@simonedesousa9435
@simonedesousa9435 5 жыл бұрын
Very good video. Thanks a lot!
@matiaskarinleiva8012
@matiaskarinleiva8012 5 жыл бұрын
Te aviso que tal queda muchas gracias no se me había ocurrido 💪💪
@madassjuan1655
@madassjuan1655 5 жыл бұрын
Lo hiciste también? El del vídeo dice que se lo hizo a 2 motos ya.
@loromat100
@loromat100 4 жыл бұрын
Que tal el funcionamiento con ese cambio.
@hencomer
@hencomer 4 жыл бұрын
Que tal amigos como les funciona el coginete
@123rusty4
@123rusty4 3 жыл бұрын
looking on eBay/ i see the bearing mite be 25x47x12mm ?
@tkurbandesign
@tkurbandesign 3 жыл бұрын
Hey Alex, great video! My XT filter checked out fine, and engine still runs, but with lots of "piston slap" noise. I adjusted valves to spec, and they weren't far off. The bad; when I turn my crankshaft manually with a wrench, it makes a very audible metal friction sound throughout the strokes. Any thoughts before I take it into a local mechanic? Is a top end rebuild within a beginners ability and worth the $ for an XT? 10kmiles btw. Thanks again!
@stephenhowarth6957
@stephenhowarth6957 4 жыл бұрын
Great video and thanks for posting. I made the same mistake this week with the wrong oil filter. The bike started chirping and then locked. It runs now (with the proper filter) but I've been told to do this. Are you fairly sure only the bearing is needed ? Thanks in advance.
@alexkram
@alexkram 4 жыл бұрын
I think so. It's not hard to do but you will have metal shavings to clean up too probably. I did not need to replace the cam when my other bike seized, I just cleaned it up with some scotchbrite.
@stephenhowarth6957
@stephenhowarth6957 4 жыл бұрын
@@alexkram Thanks ! I let it idle a bit with a new filter and there were no shavings at all in the filter. Odd.
@aaronlawrence8629
@aaronlawrence8629 5 жыл бұрын
This was an amazingly helpful video!! Did you happen to keep your old aluminum bearing?
@alexkram
@alexkram 5 жыл бұрын
I'm here to help. No, it got trashed. You could see visible wear on it.
@chaddickerson1887
@chaddickerson1887 6 жыл бұрын
So far so good? How's it working for you?
@alexkram
@alexkram 6 жыл бұрын
Chad Dickerson no problems yet. Only had it on two rides though.
@efirizaki5656
@efirizaki5656 4 жыл бұрын
@@alexkram keep up inform🙏😁
@dillondomalewski7127
@dillondomalewski7127 4 жыл бұрын
Was the bike making a loud ticking noise when this happened
@alexkram
@alexkram 4 жыл бұрын
I have converted two bikes. The first one I bought seized up so I didn't hear it run. The second one I converted is the one in the video and it's bushing was fine so the bike sounded normal.
@thomaspowell5011
@thomaspowell5011 3 жыл бұрын
That’s my question also. I ran my wr250 filter in my wife’s xt225. Just saw this video, and wondering if it will fix. It sounds like rod knocking
@lucaspeden3727
@lucaspeden3727 Жыл бұрын
Wr250 fits an xt250- paper element. TW200, xt225, ttr225 and 230- same thing- all have a fine mesh metal filter with a special oil hole. Did you watch the beginning of the video? And in my opinion those ball bearings would not hold proper oil pressure
@indy1234567891011
@indy1234567891011 6 жыл бұрын
Great video, thanks
@ChaoticDetour
@ChaoticDetour 5 жыл бұрын
Any update on this?
@alexkram
@alexkram 5 жыл бұрын
Still going strong, 1000 miles later
@larry3138
@larry3138 6 жыл бұрын
Well done!
@dcspinz7883
@dcspinz7883 5 жыл бұрын
Just did this last week to a ‘97.
@StocksFarm
@StocksFarm 4 жыл бұрын
Gonna do it to my 97 this weekend
@dcspinz7883
@dcspinz7883 4 жыл бұрын
Stock Junkee84 put the bearing in the freezer for about an hour, it’ll help install
@meleeds
@meleeds 6 жыл бұрын
Is your knee completely better now? I recently broker my patella and will be starting physio soon. Praying I get a full recovery
@matiaskarinleiva8012
@matiaskarinleiva8012 5 жыл бұрын
Tradusilo en español
@porvida6543
@porvida6543 5 жыл бұрын
Whats the advantage of swapping to ball bearing?
@alexkram
@alexkram 5 жыл бұрын
There are a few advantages. I think the ball bearing will last much longer between failures because a journal type bearing requires some oil pressure to work and the design of this engine, with holes at the cam lobes, does not provide oil pressure to the chain side bearing. A ball bearing does not need oil pressure, just some oil now and then. This is my understanding of how these types of bearings work. Also the stock part costs $60 to replace while the ball bearing costs $5, so once seized the ball bearing is the cheaper choice too.
@matiaskarinleiva8012
@matiaskarinleiva8012 5 жыл бұрын
Le queda grande el ruleman a árbol de leva influye en algo ?
@guillermopenarandacuervo689
@guillermopenarandacuervo689 2 жыл бұрын
hola, tengo una xt225 mod 2005, veo que decis que te quedo grande el ruleman y tengo en mente hacer este cambio, le instalaste el 6005 ?, o cual le colocaste ?, gracias.
@matiaskarinleiva8012
@matiaskarinleiva8012 2 жыл бұрын
@@guillermopenarandacuervo689 el mismo lleve a hacerle un buje así entre apretado
@adolfadolfvich3253
@adolfadolfvich3253 4 жыл бұрын
🎥 👍 👍 👍
@ThePudgie123
@ThePudgie123 5 жыл бұрын
Nice vid!
@LuisRamirez-mn6mb
@LuisRamirez-mn6mb 6 жыл бұрын
Thanks, thanks.
@chamindaperera3257
@chamindaperera3257 5 жыл бұрын
is it possible to do this for Yamaha TW200?
@alexkram
@alexkram 5 жыл бұрын
I am 99% sure it is the same.
@chamindaperera3257
@chamindaperera3257 5 жыл бұрын
@@alexkram Awesome. thanks.my tw's cam sprocket got a little play. Is it normal? How to know the collar is worn?
@alexkram
@alexkram 5 жыл бұрын
@@chamindaperera3257 it isn't that hard to take it out and inspect it but if you can wiggle it around that isn't good. Be sure to set those valve clearances after you make any changes.
@chamindaperera3257
@chamindaperera3257 5 жыл бұрын
@@alexkram Thank you. it's really helpful. ☺
@chamindaperera3257
@chamindaperera3257 5 жыл бұрын
@Suzukisan Thank you. I think my one is worn it wiggled more than 1mm horizontally. 😞
@shalimix
@shalimix 3 жыл бұрын
I Think Yamaha TW 200 also need this upgrade ...
@gabrielalegria1901
@gabrielalegria1901 4 жыл бұрын
Videl moto xt 225 en español
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 56 МЛН
Yamaha XT225 COMPLETE engine REBUILD
12:31
Benjamminoutdoors
Рет қаралды 6 М.
Does Pre-FILLING The Oil FILTER Cause Engine DAMAGE?
14:03
The Motor Oil Geek
Рет қаралды 3,4 МЛН
Why We Build Houses with Nails, Not Screws
17:05
Essential Craftsman
Рет қаралды 1 МЛН
Motorcycle Mechanic Reacts to "Motorcycle Hacks"
16:06
The Bearded Mechanic
Рет қаралды 494 М.
Capable Machines - Amazing Road Trip  on XT 225
12:37
clark underwood
Рет қаралды 24 М.
YAMAHA XT225 Valve Adjustment
11:08
blancolirio
Рет қаралды 36 М.
TTR230 head gasket inst......wait WTF!!!!!
20:34
da braap shack
Рет қаралды 5 М.
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН