The diesel fuel went pass the rings. I recommend changing the oil and filter before you try to start the engine because the fuel will strip the oil off the bearings
@SweetHill-o3z14 күн бұрын
While you are at it just order a new fuel tank( stainless,) it's only money .
@milesbackman382314 күн бұрын
Shows a bottle of ATF in beginning then uses diesel
@milesbackman382314 күн бұрын
@@SweetHill-o3zpersonally, I like plastic tanks.
@WalterGreen-k3h15 күн бұрын
First time i ever seen a impact gun on sparkplugs
@RC-qf6wr15 күн бұрын
That;s why he is BAD chad.
@rogerpatton-zr7qd15 күн бұрын
Don’t never do that.
@rogerpatton-zr7qd15 күн бұрын
Not smart
@jtuck606515 күн бұрын
He did it last vid too when he first started working on this engine. A mechanic he is not lol
@joelav722215 күн бұрын
I’m sure he won’t use the impact to install the plugs ..???
@simpleplumbinganddrainage274514 күн бұрын
Stop doing push ups
@andsonpoa14 күн бұрын
Snälla Jolene, gör armhävningar istället för den där mannen. Det skulle vara mycket trevligare att titta på!
@philippeparret-dr8er14 күн бұрын
Ferme la
@kevinfahey832514 күн бұрын
His show, stop watching then !!!
@VernonDyer10 күн бұрын
Should let Jolene do the push_ups....
@PeterDowd-r9b15 күн бұрын
Chad and Jolene , get a new gas tank , the crap will always plug up the gas line
@Still-Braind15 күн бұрын
This is hard to watch, He should perhaps watch a few Vice Grip garage episodes
@deanbrunner26114 күн бұрын
Matt from Irontrapgarage has a whole stable of model As and has done tons of these
@arejetko14 күн бұрын
Or maybe - goggles and a work bench.
@okolepuka313414 күн бұрын
Don't change a thing.. Homer Simpson irl
@BillMac6914 күн бұрын
Why
@Aaronlewis884614 күн бұрын
Or just let the guy do what he wants to do. And if you're not happy with what you're watching then go watch something else. It really is that simple clowns
@redmike791115 күн бұрын
The rest of the diesel fluid is now in the crankcase. Add some marvel mystery oil to each cylinder spark plug hole to lube the rings. Then change the crankcase oil & filter if there is one. Spin it over with the starter, then start it using starter fluid. Once it’s running for a bit to get a little heat in the motor. Shut it down and change the oil again. It will work itself back in.
@RC-qf6wr15 күн бұрын
Are you kidding? He most likely will just change the oil/filer and be done- flushing? HAH that'd be wasting the oil he just put in! - Bad Chad prosess: fast simple and cheap and with no rhyme or reason
@jamesh496615 күн бұрын
Marvel mystery oil is a proven product. Been using it 60 yrs. The good thing about it is it's multi purpose. Good in the gas and good in the oil because it reduces friction.
@wilddave10015 күн бұрын
OK CHAD ITS TIME U GET A MECHANIC TOO GET THE CAR RUNNING , COME ON NOW , GET SOME HELP AND BE DONE WITH IT . JO USE YOUR INFLUENCE . IT WOULD ONLY TAKE A DAY OR 2 . TOO GET IT RIGHT AND NOT DAMAGE ANYTHING GET SOME HELP .
@superpela114 күн бұрын
That's true but remember this is all content for the channel, more controversy more views equal more money, that's it
@richardrasmussen713514 күн бұрын
Absolutely selling content like mad. Rolling in the cash.
@ryanhosier630515 күн бұрын
That is not how you free up a motor KZbin it That Heat gun Isn't doing s***
@johnhenderson254815 күн бұрын
It's free isn't it Einstein
@jtuck606515 күн бұрын
But, it hot he says 🤷🏼♂️😂
@kbschulze15 күн бұрын
Heat absolutely helps and a heat gun gets extremely hot
@TCW-hw6iw15 күн бұрын
Guess you have never tried to start a diesel engine in -40 degree weather!!
@leonard-l6j14 күн бұрын
Jimbo told him to do that
@bradleymckay36514 күн бұрын
I just can't watch chad work on engines because this is beyond ridiculous.
@MrBmxbrawler14 күн бұрын
Instead of commenting complete horse shit, call or email Hiltz and give him advice. But we all know you're just a shot in the dark too
@normbissonnette886614 күн бұрын
@@MrBmxbrawler Good or bad ,this is entertainment of which Jolene and Chad are making $$$ .
@markstephens18714 күн бұрын
😂😂😂
@RapidFlowConcretePumping13 күн бұрын
I agree, but I think it is an act for more views, no way he's for real!!!
@jazzking9913 күн бұрын
So don't.
@Frank-mm2wo15 күн бұрын
Hard to watch, I had to speed through this episode.
@charleslindsay320113 күн бұрын
me too
@patmcardle276914 күн бұрын
I still don't get the push ups ??
@andsonpoa14 күн бұрын
Snälla Jolene, gör armhävningar istället för den där mannen. Det skulle vara mycket trevligare att titta på!
@witchdoktor6914 күн бұрын
@andsonpoa Especially if she did the old school female version of push-ups.
@yeahright30214 күн бұрын
so dumb for sure!!
@BUB-oy7me15 күн бұрын
The valves are opening and closing! Take that impact from him. The diesel is in the oil pan 😂😂
@BernardGlazier15 күн бұрын
No it is in the rad
@faucetman15 күн бұрын
Chad, you are scaring me with that gas tank. Having blown one up once (lucky to be here still in one piece). Gas tanks are TOO dangerous to mess with. Is your life and shop worth $600?
@Charlee-w1u14 күн бұрын
Had a battery blow up, new respect for batteries. Gas tanks also is the last thing to be unsure of.
@peterfavre402214 күн бұрын
Can’t buy those at the dollar store
@budwebster103114 күн бұрын
@@peterfavre4022 next to the chrome tape
@williamburdon699314 күн бұрын
The diesel fuel has gone past the rings and is in the bottom of the engine and in the oil pan now. You need to change the oil, run it a couple minutes ,then change it again. run it 25 miles and change the oil and filter again. If there is diesel in the oil it will tear the engine up. Mustie1 is a great mechanic and fix it guy, he just built a gas tank cleaner that runs off a drill , probably cost 20 dollars to build, it worked great, especially if there are no baffles in the gas tank, you put bolts and nuts in the tank with some cleansers and spin it ,Worked great! Then put a fuel filter in the line to catch anything you couldn't get.
@gregl567714 күн бұрын
Sounds like a bunch of nonsense from someone who's never worked on a vehicle. Diesel in the crankcase use to be ran 100 miles and oil changed. Used to break up build up. It's a great solvent. Same with adding a gallon of diesel to 8 gallons of gas to clean injectors and so on. Way safer and better than Lucas and injector cleaner junk you buy at your local auto parts store.
@TommyJensen-pl8qz13 күн бұрын
I bet he doesn't change the engine oil or filter 😁
@brianvandemortel671015 күн бұрын
The fuel line should be changed also
@edwardlowery651014 күн бұрын
Thanks!
@PeterRaedel14 күн бұрын
Time to find a mechanic Chad as it is very easy to see you have no idea. Use a proper hand spark plug remover. Heat in cylinders will do nothing Pay the wages for a MECHANIC
@gregl567714 күн бұрын
Wrong heat will cause different metals to expand at different rates separating them especially if they are rusted. Any half wit mechanic has put heat on a rusted objects to get them to move. 2nd there is no such thing as a proper hand spark plug remover. If you are talking about a spark plug socket. The only difference between that and a regular socket is it has an o ring in it. The oring is suppose to grab the spark plug so you don't have to fish it out with a magnet. The original tool to remove a spark plug was a open end wrench. Y'all have never worked on anything. How are you guys so confident but so wrong at the same time
@danielplummer638514 күн бұрын
Chad, Jolene, & Fina, congratulations on getting the engine unstuck! Don't listen to the people telling you that you need tp pull the heads off or rebuild the engine. The next thing that I would do is to either pick up a quart of Marvel Mystery Oil or if they do not have it around you then a quart of regular oil. I would use a heavier weight oil to lube up the rings and valve stems because the diesel fuel will have washed any lubrication away and just pour a small amount in each cylinder. I would then change the oil before turning the motor over anymore because the bearings will be sitting in the diesel fuel and turning the motor over will cause wear. Then I would lay some rags over the spark plug holes and crank it over with the starter until it builds oil pressure and sprays out anything left in the cylinders. I am afraid the carb will be fuel of bad fuel also unless it was never started after the new engine was put in. I would also check a plug wire for spark when it is spinning over. If the carb is not full of bad fuel and if I had spark I would put the plugs back in and try to start it. If I got it running I would then change the oil again making sure that I put in oil for older cars the newer oils do not have the needed additives in it. Those suggesting watching some Vice Grip Garage on KZbin are right on the money Derek does alot of frozen engines and is extremely knowledgeable. I wish you the best getting it running. Great video as always Jolene!
@DavidCampbell-bg7id14 күн бұрын
I was thinking how Derek does it.
@John-c4b6y12 күн бұрын
Thanks for the Tip
@chrisrichards133915 күн бұрын
There's no way anybody should ever need to use an impact on sparkplugs.
@LarryBaldwin-y2d15 күн бұрын
There's a right way & there is a Bad Chad way!!! His saying is you do it the way you want to do it & I do it the way I want to!!!
@geddonmeansome983415 күн бұрын
You shouldn't be using a jigsaw on a gas tank, think about it one spark from that saw and Jolene and you are toast.
@BigDaddykik197314 күн бұрын
Oh well he makes it work
@arejetko14 күн бұрын
Unless someone like Chad spot-welded them in
@witchdoktor6914 күн бұрын
Unless they were seized. Maybe he tried a socket wrench. How else was he to get them out?
@skippeery533315 күн бұрын
Chad does it the hard way
@gerrycomfort702714 күн бұрын
CAD DO THING RITE HE VERY GOOOD
@josephjohnson307314 күн бұрын
I would suggest removing the oil pan and cleaning it and making sure the oil pump screen is clean before attempting to start it.
@omarnavarro57215 күн бұрын
Chad you are not mechanic get someone else 😂
@tander185215 күн бұрын
He can’t he burned all his bridges now he doesn’t have any body to help him.
@tazwell100015 күн бұрын
he will take a grinder to it SOON
@tazwell100015 күн бұрын
@@tander1852 Oh but he can do push ups
@stevebennett324815 күн бұрын
Putting heat in does nothing
@AshlynnCairns14 күн бұрын
Can’t stop laughing at that part. Absolutely hilarious!
@EugeneThorne15 күн бұрын
don't be so cheap! get a new one
@mrsmith69714 күн бұрын
Say the rich man..😊
@darwinfoster742015 күн бұрын
It gets harder and harder to watch this channel.
@barrystoy822215 күн бұрын
This channel bucks anymore
@stevewight140914 күн бұрын
Then don't I would suggest....that's wut I do wen I get tired of a channel
@BigDaddykik197314 күн бұрын
Please please please please please please don't we're sick of hearing you complain.
@BillMac6914 күн бұрын
Don't bye
@jiminycricket223013 күн бұрын
@@darwinfoster7420 LOL well thats easily solved then right? Go watch some one else and whine over there...
@garrydewar938214 күн бұрын
Chad, at the end of the day you will save a lot of money if you hire a mechanic to work on the 34 Ford.
@MrBmxbrawler14 күн бұрын
I don't think you comprehend the purpose of this channel.
@edswain535213 күн бұрын
He had one but he quit
@cpstone10014 күн бұрын
I must admit it’s funny watching him keep looking for the diesel he poured in. Llike a dog running from gopher hole to gopher hole.
@jtuck606514 күн бұрын
@@cpstone100 😂😂😂😂
@RapidFlowConcretePumping13 күн бұрын
lol he wondering where it went, shows how much he knows about an engine.
@JHam-bd7wu14 күн бұрын
Boy this is getting hard to watch.
@robertthomas559015 күн бұрын
A bull in a China shop.....watching Chad doing mechanic work.
@jerrygriffith623215 күн бұрын
Chad doesn't have a clue about the mechanical aspects of working on a engine, all of the diesel fuel in the oil pan
@lukeandjilljelsma65415 күн бұрын
That's just what I was going to say. It's not coming out because it isn't there anymore. That's how the pistons got unseized.
@kbschulze15 күн бұрын
Pretty sure he knows that. Although he will be the first to tell you he is not a mechanic.
@kevinleonard6214 күн бұрын
How many engine builders can paint a car or do body work
@joeblow538114 күн бұрын
@@kevinleonard62way more than you can imagine
@richardsmith390514 күн бұрын
Chad may not be a full flegged Mechanic but it would be nice to protect the paint by putting a cover on the fender.
@RobertImhoff-qb5ol15 күн бұрын
Ya , not a good idea with a grinder , your crazy ,your gona blow up
@littlered188015 күн бұрын
Hey Chad you don’t use an impact gun on spark plugs
@roadwarrior481315 күн бұрын
They were already loose.He was taking them out very slowly...
@LarryBaldwin-y2d15 күн бұрын
@@roadwarrior4813 Yea, right!!!
@roadwarrior481315 күн бұрын
@LarryBaldwin-y2d open your eyes...LOL..
@MarkBindley-uc6zh15 күн бұрын
@@roadwarrior4813 if loose still don't mean using impact gun to get out . that just silly on old plugs
@howquick14 күн бұрын
@@LarryBaldwin-y2dhe already had them out previously…he’s taking the bottom ‘threaded’ adapter out with the impact gun.
@Perry-i4u15 күн бұрын
He really don’t know shit about the mechanics of a car.. Good thing he knows how to use a zip cut..
@jamiepalmer-oc7ey14 күн бұрын
Glad he didn't get the zip cut out 😮
@Gas_n_Gears14 күн бұрын
I heard him say the dirty handprint on the top wouldn't matter because he's cutting the top off.
@cliveburton899214 күн бұрын
That was a joke, didn'tyou see his face ?@Gas_n_Gears
@Gas_n_Gears14 күн бұрын
@cliveburton8992 Yep!
@jacobkamakian175215 күн бұрын
Miss your buds now Aye?
@bmw1987714 күн бұрын
Did both of them leave?
@tazwell100015 күн бұрын
Damm , stop the push up🤨
@brianvandemortel671015 күн бұрын
You should really hire a mechanic to help you out just when you need them can’t be that expensive sometimes you just need to bite the bullet
@AlanKrushel14 күн бұрын
It’s really too bad that a car of that calibre gets wrecked by a guy that doesn’t have a clue of what he’s doing and even if he did he’s too cheap to do it right ! Cars like this shouldn’t be sold to guys like this !
@witchdoktor6914 күн бұрын
How is it getting wrecked? He is making it driveable. He said from the start he didn't want to restore it. A ground up restoration would cost $100,000 if it was at a shop.
@yeahright30213 күн бұрын
so true!!!
@markobiko564613 күн бұрын
Explain what is wrecked on it? The engine is freed up. Have seen many old school mechanics do it this way.
@davidcrawford571113 күн бұрын
You got the money , you can do what you want , Pilgrim !!
@raystine105515 күн бұрын
Drain and put in fresh oil before you turn it over with a battery. And put a little oil in each cylinder.
@robertshemory354115 күн бұрын
I cannot watch this any more. 😮
@jerryhudnall184415 күн бұрын
if after soaking the inside engine to break rust or carbon loose and it is still locked up, simply put it in high gear and push it backwards this has been done hundreds of times though out 40's-50's -60's-70's in area i'm from, be wroth try, simple enough, would not be?
@JimSmith-x1c14 күн бұрын
Should NEVER need an impact on spark plugs never !!!
@mattcasoni14 күн бұрын
I almost 💩 myself seeing that
@gangiolini620114 күн бұрын
You are correct: You should never “need” an impact unless the darn things are seized-up…in that case, there is nothing wrong with using short bursts to try to loosen them up…all is in the “control” of the tool…I’m pretty sure he will not use an impact to install the new ones in 😏
@mattcasoni14 күн бұрын
@@gangiolini6201 I have to re-watch… I swear he was tightening them
@karenruybal275914 күн бұрын
You obvious are not to smart impact is the right tool for flat head engines my dad did it all the time back in day 31 years as a mechanic for gsa
@robertlemoi791914 күн бұрын
The blind leading the blind.
@rcctech135614 күн бұрын
This guy is becoming comedic by the day.
@Davey-Drums15 күн бұрын
A stuck valve stays OPEN. If it is closed, it is working. Remember, valve opens once for every TWO revolutions...
@StevenCopeland-l4v14 күн бұрын
First of those do not look like aluminum heads they look like cast-iron, original second of all I really don’t understand the heat gun what the purpose of that is if you’re trying to get that unstuck need to drop some marble mystery and cylinders let it sit for a couple daysbut you do you I’ve really seen this guy do nothing but fuck up some really valuable cars and then just toss him out to the side after he’s done screwing them up
@barrystoy822215 күн бұрын
Buy a new gas tank wakeup and smell the coffee this content SUCKS CHAD DOESN'T NO WHAT HES DOING
@vleldaddio2109 күн бұрын
It is Chad's channel ! Like Chad doing what he feels comfortable doing and like he stated on a previous video in the end he doesn't have to give a shit about what people think or care as long as he is satisfied 🙌👍 Enjoy all the different cars problems , triumphs and setbacks it is called LIFE THANK'S CHAD
@BroknlukCyr-t3e15 күн бұрын
Once the engine is running pour Marvel Mystery Oil in the gas tank and this isn’t snake oil - this really works to help lubricate the cylinder walls and also keep the carburetor clean.
@kenmanda574315 күн бұрын
.chad what happened to natt
@edwardsjohnpaul14 күн бұрын
Chad is a middle-aged white guy, on camera. He's gonna have some confidence, it's inevitable. Doesn't mean it's productive. I love this guy, he really is fantastic and inspirational, and is a lot more than what so many are... but damn. I think (and hope) even he sees there's something missing here.
@joeslash7714 күн бұрын
Rinse it with mineral spirits or various first. You could always go the cheap way and use hot soapy water first to neutralize the gas first.
@daveparnell404414 күн бұрын
What the hell did i just watch?
@MrBmxbrawler14 күн бұрын
you both just watched a millionaire get a few more bucks in his pocket. He thanks you for participating ❤️ 💕 😘
@daveparnell404414 күн бұрын
@@MrBmxbrawler He is welcome. Thanks for the entertainment. More cringes per hour than Fawlty Towers
@budmangt214 күн бұрын
@@MrBmxbrawler That's a good one, LOL!
@spanner50214 күн бұрын
Why not do your push-ups in private?
@andsonpoa14 күн бұрын
Snälla Jolene, gör armhävningar istället för den där mannen. Det skulle vara mycket trevligare att titta på!
@yeahright30214 күн бұрын
@@andsonpoa get lost dmb arss and stop saying the same thing!!!
@yeahright30214 күн бұрын
i think he thinks its funny,but yet its soo sad!!
@williamerentfro954313 күн бұрын
I can honestly say that I will not watch Hiltz anymore.
@decadesofmusictimemachineh195415 күн бұрын
Thank you Chad and Jolene for the videos on fabricated, very knowledgeable, Ronnie Hornback from Louisville Kentucky
@trevorrhoode60014 күн бұрын
This guy is a danger not only to himself but Jolene is in danger too! 😮 We know Chad is not that bright but I thought that Jo was clued up with the internet and technology! 😢 Enough all ready guys, do some homework before you tackle a job like this on air! Safety first! 😮
@charleswitherbee554915 күн бұрын
The diesel fuel probably went into the oil pan Pabst the rings.
@johncameron286814 күн бұрын
I get it now. It's a comedy show.
@Bobsteven88114 күн бұрын
It's definitely no safety show
@briancoetzee33913 күн бұрын
🤣😂🤣😂
@howquick14 күн бұрын
Right near the end there after you had your hands in the tank…when you walked near Fina…she looked at you like “don’t you even think about patting me” 🤣🤣
@stevebennett324814 күн бұрын
Chaddy put a battery in it and spin it over without the spark plugs in it for a bit, put a little marvel mystery oil in each cylinder first then crank it
@Davey-Drums14 күн бұрын
Get the starter working, spin the engine, and do a compression check. That will tell you a lot. Stuck valve will be zero compression. Rebuild the carburetor along with the new fuel system. Just take it apart, clean it, and reassemble with new parts in kit. EZ Fun stuff!
@EricClark-io7rf15 күн бұрын
Most of my projects I go with what I’ve learned from others,,if it not going well for me I just call in the experts or pick the brains of those who are experienced with what is holding me back. Never say never. It’s the reason I tune in everyday to learn,enjoy,and throw the rest away,and move forward.
@JHam-bd7wu14 күн бұрын
Are you kidding me. Cutting a gas tank?
@mrsmith69714 күн бұрын
If its hole inte the tank it dont explode..it possible burns.. but its possible more water an petrol because it has corrosion so much
@gregpanek52314 күн бұрын
You were worried about making sparks with the zip wheels but you used electric tools that the brushes spark on the armature. Air tools are the only ones that don't spark (except for the blades if you're not careful).
@MarkBindley-uc6zh15 күн бұрын
Can't you find someone that knows more about mechanical things, or doesn't any of your so called friends want to help you. Must of made a lot of people not want to help you for little bit . might be helpful to watch some KZbin videos on mechanical things to learn better ways
@stevebennett324815 күн бұрын
Oyh ,heat is doing absolutely nothing, last night vicegrip garage got a motor unstuck in no time, you really could learn from his videos
@varioushardcore14 күн бұрын
Pshaw! You can't put Derek in the same sentence with the Great Bad Chad. I don't see Derek pretending to do 50 push-ups at the end of his videos...Or abandoning every project ever started once money needs to be spent and mechanical knowledge is required.
@ThomasSmith-hh8fp14 күн бұрын
LMAO !!!@@varioushardcore
@barriecollins683814 күн бұрын
Chad and Jolene just my belly button as you say but if I was. You I would put a little engine oil in the cylinders now to lube them back up also replace the engine oil cause the diesel will have passed the rings and be mixed in with your oil. It’s great that you have managed to free up the engine keep up the great work the both of you
@billysharp338814 күн бұрын
I believe he will get it done!
@tannerlawson172114 күн бұрын
All man I'm sorry about your gas tank I hope things work out the best for u 2 . But I only pray good positive thoughts to your way u 2 make a awesome job u 2 well figure it out 😊
@Cheva-Pate14 күн бұрын
I’ve been scrolling through like 8 years with Bad… he has destroyed a lot of cars….
@arejetko14 күн бұрын
Turn a 59 Volvo into a led sled with front and rear bumpers that don't mach. Chad be Bad.
@1304GARY14 күн бұрын
I saw you put the diesel in all the spark plug holes, if the valves are open on that cylinder a quantity of the diesel would have gone down the exhaust valve or inlet valve it’ll just need a bit of turning over to clear it away, drain out oil and change the oil filter after
@brentvonaschen706415 күн бұрын
Likely the diesel fuel is in the bottom of the engine Oil change needed.
@ronsnyder743514 күн бұрын
Take your time, you’re doing all right, it’ll come!!!
@jacobkamakian175215 күн бұрын
Driver rear cylinder was stuck only.. that’s why it shot out had nowhere to go man..
@Bobsteven88115 күн бұрын
I can't believe you didn't have a spark plug socket or maybe or maybe I do know why
@siouxperirish14 күн бұрын
I agree that you should go with a new tank or have this one relined. There could be any list of bad things put in that tank from an enemy of the previous owner. Everything that comes through those lines could damage the engine or at least make it very difficult diagnosing any future issues if there is trouble. Easy for me in the armchair to make suggestions but if you do put a new tank on there, all the lines should be made also.
@davidlajeunesse207215 күн бұрын
Make sure you change the oil before you even try to start it.
@donatvezina418615 күн бұрын
Keep up the good work my friend
@hahahaha566314 күн бұрын
If all of these mechanics had a KZbin channel I’d have more to watch
@JohnFlaimsr14 күн бұрын
Then you mite learn something.
@ry49114 күн бұрын
Well done Chad . Longing to hear it run . Best wishes to you both.
@DavidMunson-g3r14 күн бұрын
If Chads doing more than fab work should get another mechanic
@ianbarnes626614 күн бұрын
I shouldn't think there is anyone in Nova Scosia that would want to work with him.
@StephenCann-to4mr15 күн бұрын
Nice see the motor is un stuck keep up the good work Chad and Jolene good camera work 😊
@dalecherry404415 күн бұрын
Make sure you drain and change the oil before you start it. Most of that diesel us in the oil pan.
@TNridgerunner4215 күн бұрын
Great job Chad on getting the engine unstuck I think it's funny how so many people told you that you were wasting your time that your not a mechanic you should get someone else to work on it I stopped questioning you a longtime ago keep up the great work God bless everyone
@richardedwards335415 күн бұрын
Just a bit of advice from a flat head Kiwi,with 50 yrs experience,get a new 6 volt battery,and a compression guage,leave the plugs out,jam the throttle open,get Jolene to press the starter and check your compression, simple as,,you can have a couple of low readings,once you get around to starting it,they may come right
@mattcasoni14 күн бұрын
This seems like the very best idea. This is the answer.
@arejetko14 күн бұрын
Said someone who knows what to do :)
@RadHameth3314 күн бұрын
Love that car! Looking good y'all-
@josephjohnson307314 күн бұрын
The hand crank could be stowed under the front seat.
@dawitkassa313113 күн бұрын
CHAD, My 50 years old car gas fuel tank was worse than yours. when i first opened the fuel screen tap. I added two galons solvent and drained the old fuel. After that, I fell it ten gallons of venigar and sat it for a week. I flip over every two days. After a week of wait, I drained the venigar and renise it by using a power wash. The results were great. The interior of the gas tank shines like silver. I installed it back, and it holds clean gas and engine burs great.
@KyleWorkman-c6u15 күн бұрын
I think you should leave the bumpers alone on the Volvo for a while anyway. I'm loving the loving the look of the Ford.
@mattcasoni14 күн бұрын
Chad has built more cars than I’ve owned. It’s very impressive. I really wouldn’t heat that. It wouldn’t do anything.
@Silentvalkery13 күн бұрын
Chad keep doing what you think is right don't forget we watching you cause your the best ppl will always have an opinion but go with your gut and push ups your trend call keep up good job
@terryscanlon5614 күн бұрын
Holly crap Chad! Your going to have the E P A cops knocking down your door😂😵💫
@StevenMonticelli-ex1tg13 күн бұрын
You should invest in a bore camera because the logical thing to do after unsticking a motor is to check the cylinder walls for scoring or pitting. The Rings could still be good and if the cylinder walls are just slightly scored than you would be able to hone the cylinders and use the rings that are still in the motor. Cuz at the end of the day you could end up ruining the rings and then you'll be at square one again. Just my experience and advice.
@sschliebe46114 күн бұрын
Should have let someone else buy this car…
@GuyPearson-g7d14 күн бұрын
Sometimes it makes sense to spend the money then to try and tackle a old part in this case the gas tank soak the sending unit in carb cleaner for a few days it may be reusable. If I may the next time you need to work on a gas tank fill it full of water then use methalhyrate you can buy it buy the gallon, it will.dry up the water it's what's in gas line antifreeze.
@911hillclimber15 күн бұрын
This is hard work? Heads off, clean it all up, do the valves and back together with fresh gaskets etc. Re-fresh ignition, fresh oil and get the fuel to it and start it with a fresh battery. Decent garage man will do this easy in the area?? Will run a treat and not cost too much?
@cherrycrawford486513 күн бұрын
At least he is trying, give advice to help rather than critize!
@danielcronk996313 күн бұрын
Exactly, why do people watch if all they can do is hate on Chad. I tend to not watch things I don’t like. Just saying
@wesleypulkka744715 күн бұрын
Chad, put in third gear!
@troygrant91514 күн бұрын
Condolences to Jolene & family
@lukeandjilljelsma65415 күн бұрын
Hook it up to the suburban and tow it around the barn.
@defaultname208914 күн бұрын
I am pretty sure most diesel is in the oil pan so Change oil before attempting starting