Yuneec Q500 open / view inside / Innenansicht / assemble new chassis / Gehäuse wechseln

[@HDMann292]

Great Video ! You made it look so easy..

[@mulder2400]

I'll bet your great grandfather worked on the Messerschmitt Bf 109, huh. lol You Rock dude ...

[@Frank-rh7vh]

Toll gemacht! Ich hoffe, dies nie tun zu müssen ;o) Super!

[@georgebeorn159]

You make it look so simple, how did you become so proficient? thank you for the video.

[@JohanSpjuth]

Thanks for this. Will attempt the exact same procedure on my Q500 4K tomorrow. Wish me luck. I'm gonna need it. :)

[@rickmooijman6195]

+Johan Spjuth Did you manage it? I'm ordering some parts to try this aswell. Can you share any tips and tricks? When you're placing the mainboard back, how do you know which wire to connect to the engines and ESC's?

[@JohanSpjuth]

I did manage it. :) However, I cut the power cables along half way along each beam so they never came off the main board. Make sure you label the power and ESC cables with a piece of tape so you know which ones go to which corner of the new body. The ESC cables disconnects from each engine bay so no need to disconnect those from the MB either. The soldering I did was on the ESCs (plus and minus engine cables from MB) + connecting the cut power cables back together. For the latter, I used a piece of shrink tubing for each lead to isolate the solder spots. I hope that makes sense.  Make absolutely sure you aren't in a rush and be thorough. It will take quite a few hours to complete. Good luck.

[@rickmooijman6195]

+Johan Spjuth Thanks! Those are great pointers. I will make sure to follow it!

[@TheTabugman]

+Rick Mooijman No worries. Oh, and make sure to take a lot of pictures as you go along, for reference when you reverse the process. That helped me a lot.

[@rickmooijman6195]

Thank you both for the tips and tricks. My parts will be delivered today, so after the weekend me and my buddy will put everything together. I'll post my findings here!

[@ericsantiago5077]

Very impressive great job

[@marianowak6489]

Danke - Thanks

[@thinkjon]

Thanks for the video, nice to have a complete understanding BEFORE diving into the body replacement myself. My question, why "cut the power wires" than unsoder them? Less chance of short circuit something if the new soder was not completely clean? Your advice is appreciated.

[@josephquattrone9571]

tres bien merci pour la démonstration

[@Antrax360]

Please let me know how u fixed those arms like that and if it was working fine like that

[@paul.Haerkens]

Nice job

[@elwoodtwo1675]

Great video, Danke.

[@TREBLOYOLBERT]

you know esc qx1 repair v04 card that is connected to motors ?

[@codestar7]

I'd like to know where those Propellers came from.

[@ghosttjr2]

Liked very much:-P

[@kimvaartbroek8831]

hahaha...mij niet gezien.......op 4.21 hoe zat het ook alweer met die draden hahahaha knap hoor dat ie dat doet....

[@terry2xb]

Hab das Video grad entdeckt! Ist doch ne gewaltige Friemelei um alles zu Demontieren und anschließend wieder zusammen zu bauen?Ich hoffe auch niemals in diese Situation zu geraten denn bei meinem Phantom 4 hat es mir schon gereicht und der ist im Gegensatz zum Q500 relativ einfach zusammen gebaut!Ist doch super wenns dannach wieder funzt?

[@oliverlorler231]

ohje das muss ich auch machen trau mich aber nicht so recht ran köntest du mir das umbauen wenn ich dir alles schicke

[@DroneMinds]

interesting, liked. can you tell me if there is a normal rc receiver inside where you can see channels, like the channel for the turtle/rabbit mode, or is it impossible to see because circuit board? hope this make sense?

[@helmutelsner166]

+Drone Minds No, the receiver has a serial IIC connection to the flight controller (FC). The signals from remote (and telemetry to remote) are digital on Rx / Tx cables between receiver and FC: white - Tx, blue - Rx, red - +3,3V, black - 0V (Rx, Tx from FC p.o.v.). You cannot see the channels by cabling. br HE

[@theonlykris2003]

+Helmut Elsner Could this be hooked to a naza flight controller somehow?

[@RemoteChief]

I was fixing my drone changes out the chassis like you when i went o test ti the got a short on front right mototr B? any idea what could have caused it??

[@du-vonoben2863]

Remote Chief sorry - I have not a solution.

[@MrGuardalaluna]

Grazie!

[@peterrod5239]

those 3 motor wires are a bitch to solder make sure you have a good di-soldering gun once those wires are solder the board don't want to sit back in place have to be push and maneuvered back in place. this has to be the hardest part of the job those 3 motor wires X 4 spend almost 5 hours messing with those wires finally i gave up and i did my own abortion job. this guy makes it look so easy.

[@TheSubienatic]

lol.... good video some other made like 20 plus videos while you did just one... kudos.....

[@brettkramer]

Great tutorial video !!

[@Dithmarscher-Drahtesel]

Was wird als Werkzeug alles benötigt? Torx 10? Inbuss 2mm? Schlitz oder/und Kreuzschraubendreher? Sonst echt klasse gemacht!

[@guglielmodicarlo4139]

get a set of allen screw drivers,,your killing me with those little allens but great vid thanks

[@JonasRoenick]

Von innen sieht die Drohne aber nicht so hochwertig aus.

[@artministratorle]

You´ve got a ziptide fix on one arm? :D awesome :D

[@peterrod5239]

nothing like learning and listening to porn music. ..love it. thank you.