How to Make Active Tone Controls Circuit - Bass / Mid / Treble / Control Circuit

How to Make Active Tone Controls Circuit - Bass / Mid / Treble / Control Circuit
👉Get a free trial of Altium Designer with 365 and 25% off your purchase :
👉 www.altium.com/yt/ZAFERYILDIZ 👈
👉Learn about Altium 365, the electronics product design platform that unites PCB design, MCAD, data management, and teamwork: 👉 www.altium.com/altium-365
👉Free search engine for the best quality components from Octopart:
👉www.octopart.com
👉Subscribe to JLCPCB with the link below and get your discount discounts
👉jlcpcb.com/DTT
👉Circuit Diagram
👉 drive.google.com/file/d/18xzc...
Hello In this video, you will learn how to make a great active tone control circuit. I wanted to show, rearrange the sounds according to your own musical ear using this circuitthanks for watching Don't forget to like and comment, even if it's small. see you in the next video
For sponsoring my video Thank You Altium Designer
#altium
#zaferyildiz
#Controls
#electricity
#tone
#circuit

[@ZAFERYILDIZ52]

drive.google.com/file/d/18xzcxmMzFq4pQOxySA9jqhrRRqtzMmUM/view

[@ford1546]

Is there any reason for 100k? very unusual value! 20k 50k is more common. I have never seen 100k on an audio product

[@ford1546]

If you can avoid them then you should never use ceramic capacitors. They are not linear. use polyester!

[@ford1546]

If you can avoid them then you should never use ceramic capacitors. They are not linear. use polyester!

[@user-gn5ik2kr7l]

Здравствуйте и сколько мощность на выходе ватт

[@Nejdat]

Zafer Eline sağlık Kullanışlı sade bir devre oldu👌👌🙌🙌

[@ZAFERYILDIZ52]

Teşekkürler Nejdat abi

[@angelovintelservis]

I Love Your Channel - YILDIZ! With respect to you - Andrey from Kazakhstan!

[@ZAFERYILDIZ52]

Love and greetings to Kazakhstan, my brother

[@sergeyshtefan4477]

Super! Cool 👍👍👍! Amazing😍😍!!!

[@Ademilhan3460]

*Eline sağlık Zafer Usta Çok Güzel bir Devre Olmuş*

[@ZAFERYILDIZ52]

yorum ve destek için çok teşekkür ederim

[@ashraf9472]

كل سنه وحضرتك طيب الله ينور يا هندسه دايما مبدع

[@ZAFERYILDIZ52]

شكرًا

[@asistenciatecnica8986]

Los componentes van instalados al reverso de la placa.Por el lado del cobre solo debe verse la soldadura de cada elemento.

[@SRelectric]

Awesome circuit

[@ZAFERYILDIZ52]

Thanks my friend

[@analitegnost]

Dou sodara yg berbeda antara tanpa pcb dan dengan pcb ini keren bertemu disaat yang sama jarang terjadi

[@Hassen78]

عمل رائع متابع من الجزائر

[@kinctechnaf983]

Ilike this tone control.i always waching.thanks

[@ZAFERYILDIZ52]

Thank you for the comments and support.

[@romeosecretaria6968]

Nice circuit..

[@SDXTITAN]

تشکر . Thank you. saghol

[@fratiee]

Video için teşekkürler!

[@ZAFERYILDIZ52]

Ben yorum ve destek için teşekkür ederim kardeşim

[@inventorkr1]

Good job ✅

[@ZAFERYILDIZ52]

Thanks my friend

Güzel olmuş eline sağlık.

[@garygranato9164]

i'm more impressed with the "through-hole sureface mount" pcb than i am with the tone control :) :) brilliant

[@ZAFERYILDIZ52]

😊

[@garygranato9164]

@@ZAFERYILDIZ52 please do a video of making diy PCB

[@valtersouzaribeiro761]

Bom dia parabens muito bom

[@geovanepaulino7165]

Parabéns Excelente vídeo Brasil

[@ZAFERYILDIZ52]

Parabéns Excelente vídeo

[@radiotriode-sergelafon]

Félicitations Excellente vidéo France

[@GODPLAYER-py7ir]

Tebrik ederim

[@Seniman-45]

Good projects 👍👍👍👍👍👍👍

[@ZAFERYILDIZ52]

teşekkürler kardeşim

[@juancarlosponceestay]

Interesante el vídeo, en Home Depot venden brocas de 1mm para hacer las perforaciones en las placas de baquelita . Pero igual esta bien , saludos cordiales desde Santiago de Chile 🇨🇱

[@muratvural5747]

Teşekkürler Hocam. Elinizde Elektrogitara uygun bas tiz medium, presence, reverb vs. katları bulunan bir preamp devresi var mı. Elimde yaylı reverb tankı var ayrıca 2n3055 ile yapılmış çalışan anfi devrem de var fakat preamp'tan hiç memnun değilim. Preamp ve anfi katı ayrı olduğu için uzun zamandır iyi bir preamp devresi arayışındayım. Tertemiz sesi olan tonları güzel çalışan bir preamp. İzmit'ten selamlar.

[@mariosergiogroetares9343]

Grato! Show de bola e ótima didática! Ate´!

[@ZAFERYILDIZ52]

Agradeço sinceramente por seus comentários e apoio.

[@mariosergiogroetares9343]

@@ZAFERYILDIZ52 Eu que lhe agradeço com minha cordial e fraternal saudações!

[@SamoyedComputers]

Awesome

[@hengkyambar8161]

Hi sir, if I use the JRC4558 IC, is the layout the same as the diagram you gave as in your video?

[@Muhendisbeyy]

Elinize sağlık @Zafer Yıldız ustam

[@streetfighter4apkbestfight606]

Nice work man Very best I like that 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍🙏🙏🙏🙏🙏

[@ZAFERYILDIZ52]

Thank you for your support and comment.

[@MuhammadYaseen-vx5hw]

very unique video.. thanks...

[@ZAFERYILDIZ52]

Thank you for the support and comments.

[@MuhammadYaseen-vx5hw]

@@ZAFERYILDIZ52 i am watching your videos but sometime i have missed comment field becoz i am going speechless about your unique ideas. thanks you so much...

[@VietNam.2024]

Mạch tress bass... ở VN dùng từ thập niên 90 của thế kỷ trước rất thông dụng đó...

[@cars275]

İyi günler elinize sağlık , kullandığınız dirençlerin watt değeri nedir acaba?

[@gajendraprajapat4051]

Great Brother 😘💓

[@ZAFERYILDIZ52]

obrigado mano

[@Hassen78]

Fantastique

[@misssdamla]

Zafer hocam elinize sağlık. Sizden inverter devresi istiyoruz. Yüksek frekans üretip daha sonra onu 50 hz tam sinüse set eden mosfetler ile yaparmisiniz hocam.?

[@janinapalmer8368]

A schematic diagram would certainly help 😮!

[@analitegnost]

Ini yg terjadi pada asmr Bro itu terlalu rapih dan bagus

[@richardsuchy24]

WoooooooooooW 😮

[@ZAFERYILDIZ52]

👈❤👉

[@abdullahbakr430]

Araba anfisi projesi bekliyoruz elinize sağlık

[@ZAFERYILDIZ52]

👉👍

[@ulukentf]

Elinize sağlık çok güzel olmuş. Şemada entegre farklı . Kullandığınız entegre eşdegermi oluyor

[@ZAFERYILDIZ52]

Yerleştirme planında olabilecek entegreler yazıyor 3 adet alternatif

[@hasantamer9199]

harika

[@ZAFERYILDIZ52]

teşekkürler Hasan Tamer

[@muratguney8171]

Hayırlı akşamlar hocam sizlere bir sorum olacak oto ses sistemi için teyp ile amfi arasına nasıl bağlayacağımızıda gösterebilir misiniz

[@legiabao7a674]

bạn có thể chi mình sơ đồ câu tay được không???

[@MiguelDeMarchena]

Great!, decent for a demonstration but please make a version of the same circuit for stereo 2.1 and not SMD ( for more sturdiness, reliability and durability ) proper PCB with holes drilled 🙂

[@ZAFERYILDIZ52]

The pcb I shared is already designed with holes, but I didn't drill a hole, you can use it.

[@rizelimami5397]

Normal teybin cikisindan anfi cikisi almak icin bir devre yaparmisin

[@dingski_diy]

when drilling is a thing of the past..

[@LuisaAlexandre-ni4zz]

Obrigado pelos vídeos, são muito bons.

[@ZAFERYILDIZ52]

thanks bro

[@lucianomanuelmanuel104]

ei vc tem o esquema e leialt..

[@emre24aktas]

eline sağlık birde bunun stereo olanı olsa güzel olur

[@ZAFERYILDIZ52]

İki kanal için aynı devreden cift yapıp stereo pot ile kumanda edilmelidir

[@interrleak5829]

stereo mode?

[@ShunilAcharya]

👍👍👍

[@Soebektifamily]

Apa karakter ic lm358 pak

[@uniqueworld554]

Please provide circuit diagram. No diagram in your link.

[@legiabao7a674]

có thể thay 358===4558 được không vậy???

[@Dubai84]

❤

[@Producciones_Y_Sonido_Rojas]

En vez del LM358 PUEDO PONER UN 555? Pregunta seria

[@abdelhakimhassnaoui2297]

The lm358p cannot be replaced by the ne555 The replacements are lm393, or tl072, or ne5532p or ic 4558d I advise you to use the ic 4558d, as it is widely used in cassette players or radios, and if you want to set the right-to-left system, use the lm324n

[@jawad1826]

Hello, I am asking for a circuit that takes from 10 to 30 volts DC and outputs 12 volts

[@md.atiqhasan9290]

Yes

[@ZAFERYILDIZ52]

👍

[@johnhopkins6260]

3-way "active" (i.e. pre-amp level) crossover; for three (Bass, Mid, High) amplifiers, three speakers (Bass, Mid, High)

[@ZAFERYILDIZ52]

👍

[@borkatxploit3031]

Bisakah saya meminta skema

[@hajounizouhaier9048]

😊

[@edifierbass7821]

why not flash share the diagram straight on your page without going through drive link for easy access by anyone

[@tomasvacek5879]

Schematic?

[@sigitprasetyo3182]

please with subwoofer sirr...

[@SAHINYATAS]

Ultrasonik Temizleyici Yapımı Çekebilirmisiniz :D

[@omarslameh431]

ياريت مخطط/لو عمل على ذالك ولك جزيل الشكر 💙💙💙💙👍

[@ZAFERYILDIZ52]

الدائرة تعمل بشكل جيد ، ما عليك سوى التمسك بالتخطيطي

[@user-zh7kj8ph7v]

Всё классно. Лайк одназначно заслуженный за проделанную работу. Схема где ?

[@ZAFERYILDIZ52]

вы можете увидеть прикрепленный в описании видео drive.google.com/file/d/18xzcxmMzFq4pQOxySA9jqhrRRqtzMmUM/view

[@user-zh7kj8ph7v]

@@ZAFERYILDIZ52 Огромное спасибо . Успехов вам и вашему Каналу!

[@wintew6063]

this is mono？

[@mehmetkirac6690]

Deniz elektroniğin yaptığı devre bu jrc4558 yerine 358 kullanılmış

[@serdarsarac2245]

pcb kartı keşke delikli tasarlasaydınız bu haliyle çok karmaşık mercimekler dirençler bir biri içine geçmiş vaziyette..

[@ZAFERYILDIZ52]

İstersen delik açabilirsin tasarım delikli zaten

[@justjayr23]

powered by SMD technology

[@SuperUserSuper]

treble500K 😮👍❤

[@GODPLAYER-py7ir]

Dere şeması açılmıyor

[@keremseven4030]

133 lf 002 nedir abi bakır saygılar var 4 ayağı var

[@ZAFERYILDIZ52]

Honestly, I don't understand the circuit element, respect

[@sahebsakshit4052]

Pdf file please sir

[@mfayyaz9327]

Aoa, Circuit diagram file is not supported in Android type please send supported type file... Thanks I am fayyaz from Pakistan.....

[@mfayyaz9327]

Or send circuit diagram jpg or printed circuit diagram thanks...

[@user-zl2zh5nf7b]

Дайте нормальную ссылку, у меня ни первая, ни вторая не открывается)))

[@FLAYERR01]

Abi senin solar sistem ne durumda

[@ZAFERYILDIZ52]

çalışıyor yakında yeni eve taşıyacağım

[@FLAYERR01]

@@ZAFERYILDIZ52 video gelecek mi

[@pali516]

This is not seems to be a active tone controls system . In an active tone controls there should be negative feed back circuit. That system tone control gives excellent low and high frequency response. Which was introduce by mullard company in their Amplifiers.

[@leopoldofernandezjr.508]

Is it Mono sir?

[@ZAFERYILDIZ52]

yep mono

[@ZAFERYILDIZ52]

1 more needed for dual channel

[@antoniorojas2571]

Pásame el diagrama xfavor

[@ZAFERYILDIZ52]

drive.google.com/file/d/18xzcxmMzFq4pQOxySA9jqhrRRqtzMmUM/view?usp=sharing

[@floranape913]

Español

[@user-do9zq8xk8e]

Abi malzemeleri bende yok ne yapacam😢😢

[@ZAFERYILDIZ52]

internetten temin edeceksin

[@pali516]

Active tone control කිව්වට එහි නිෂ්පාදනය වසර හතලිහක් පරනයි. මලාඩ් සමාගම ද නිපදවුවා. මේක බැලු බැල්මට active tone control නෙවේ. හේතුව එහි negative feed back ක්‍රමයක් තිබිය යුතුය . ඒක්‍රමයට කියන තව වචනයක් තමයි NF tone control.

[@ford1546]

Is there any reason for 100k? very unusual value! 20k 50k is more common. I have never seen 100k on an audio product

[@flaxlsm]

Minimizing op-amp loading could be the reason, though I doubt he really did the calculatios himself. I saw a circuit similar to this on TDA2320 datasheet. You might want to check it out.

[@paolocampagnoli3478]

Mettere schema pleas

[@ZAFERYILDIZ52]

puoi scaricare dalla descrizione del video disponibile anche nel commento appuntato

[@paolocampagnoli3478]

@@ZAFERYILDIZ52 thank you

[@ronhoffman2405]

Why don't you publish the circuit diagram in your video or as a .jpg or pdf. ZIP files are notorious for containig malware.

[@ZAFERYILDIZ52]

there are multiple files

[@ronhoffman2405]

​@@ZAFERYILDIZ52 Don't care. Publish a Bill-Of-Materials, schematic and board layout separately in a safe format.

[@carlosgramajo6928]

100 K DE UN PORTECIOMETRO NO TIENE NADA DE GRAVES

[@flightheglider9191]

1 Layer-> Without JLCPCB 😢

[@ZAFERYILDIZ52]

🤭

[@rusab5130]

Монтаж у автора внушает. Я так то в классе 5-м на картонке монтировал. И на басах пердит, значит коррекция нужна.

[@CHMguiden]

Kenapa tidak TREBLE MIDLE BAS VOLUME?😂😂😂😂😂😂😂😂

[@CHMguiden]

@binyahya8135 mana tu.. tumbnail masih gitu

[@savage-zh1wb6ii7x]

Нет схемы, нет оценки,лень замучила?

[@kenkappler7304]

This is not very useful if one wants to build the project. Including a conventional schematic drawing would be far more informative than watching soldering connection.

[@ali.kh57]

خانوم اگه میشه یکم آه وناله کنید

[@sarockpashotan]

Mr Zafer why do,t you show us the schematic diagram circute us!!!what are you afraid of?!! While the other channels do that clearly and honestly!!!

[@ZAFERYILDIZ52]

If you bother to look at the video description you will see everything.

[@simontsegaygebre4196]

Useless project

[@Lmika297]

không cần ic -có chế được mới đáng nể phục .

[@lidiaarias5107]

La placa esta quemada al revés, así queda muy improlijo.

[@donaldoalfonsoecheverriapi3321]

ese tipo de construccion deja mucho que desear como profesional, inestable un alumno me viene con un circuiti asi armadoo y lo mandop a que lo haga de nuevo, estamos formando profesionakles, no chambones flojonazos, que perfore la placa y ponga los elementos como deben ser, que horror deberia darle pena subir un proyecto asi, no me pasa la inspeccion., trabajo en electronica desde el año 1976 y llevo muchos años enseñando... yo procuro la exelencia...