Zenith Super Duty Update

[@64hocus]

hello from Belgium

[@RailfanRene]

I like your eye for detail, it’s the little things that other builders won’t even think about. Also, the ELT signal unit you say to tie to some cables… I would tie it to a piece of metal instead to prevent the tie cutting the insulation of the cables over time. Just food for thought. Nice airplane though, keep on the good work.

[@johnfitzpatrick2469]

Hello Mark from Sydney Australia. The 3D printing process is a perfect solution for engineering maintenance. There are expensive accessories "completely" replaced because of a small $3.00 component that could be printed. The cost is setting up the first copy: 'that hurts the back pocket'. 🌏🇭🇲

[@travisw9071]

Finavly! Thanks for the update!

[@bradalgra8088]

Super clean build! Can't wait to see this one in the air.

[@bigmuz_pilot]

Your wiring is just stunning, good stuff mate!

[@foesfly3047]

Your plane is made of Metal. But I’m pretty sure, when you receive an award for an exceptional accomplishment, it’s a Medal 🤪 Luvya Mark 😎🎩♠️💙

[@KitplaneEnthusiast]

Thank you but any judge who would look at my paint job would walk away laughing! LOL

[@Know-Way]

Looking great Mark. Do you know what kind of filament that brake line bracket is printed from? It sure looks good.

[@taildragger7355]

Fantastic! Sweating the paint job seems contrary to the mission for this plane. She isn't a hangar queen, right? She is built to get you there with your gear and bring you back.

[@mhilderbrand7693]

Love the 3D printed brake line holder! We may have the same type of ELT? Kind of funny, I went to install the D batteries in the main unit, just to realize it already has a Lithium battery in it! Now I am thinking… how much will this cost to replace😅?

[@tomgillotti]

5:27 *Medal 😉

[@user-tl5fi9lz9z]

I defiantly want those break line clamps.

[@Tommy-B.]

I too, will defy anyone who says I can’t want them.

[@user-tl5fi9lz9z]

@@Tommy-B. ok, so I can’t spell worth crap😒

[@russellsmith3825]

Where the rear control surface stop hits the rudder could you use a couple inches of trimlock as an edge protector?

[@jerrylittle7797]

It's getting close! Is it too early to start talking about the next build? 😉

[@KitplaneEnthusiast]

Oh I’ve thought about it!

[@StubProductions]

Curious what plastic is being used for 3D printed part. Some plastics will not be suitable for this application.

[@salimnasir5231]

Does it possible to provide the windshield fairings and the roof lexan that u are using ?

[@nickjones6065]

I think you need to add D Day invasion stripes to that scheme.

[@JoesRCCorner]

Looking great. You have exceeding where am. Want to come help me? LOL

[@willluggar505]

The brake line brackets for sale yet?

[@KitplaneEnthusiast]

Five sets will be available the first week of December.

[@Orzorn]

How does the anti-walk on the steering rod nuts work? I see little slots, but those don't seem wide enough for any sort of safety wire.

[@KitplaneEnthusiast]

No safety wire is used with these nuts. The top of the nut is sort of squashed a little bit making it a locking nut. These type of nuts are used instead of locking nuts with nylon.

[@anthonyrstrawbridge]

Units swapping between imperial and metric units on plans - blueprints ?👈🤡👉

[@salimnasir5231]

Does it possible to provide the windshield fairings and the roof lexan that u are using ?