Introduction on how to open and modify 8HP TCM for standalone gearbox control unit. Follow us on: / ryutechautomotive
Пікірлер: 36
@xr500t Жыл бұрын
That was a Masterclass in Soldering!
@rayjones3473 Жыл бұрын
Nice work man iv just plugged in my turbolamik and i have a short to ground fault on speed sensor 2 do you think i possibly messed up with the soldering or mashed the sensor putting it back together
@ryutech_automotive11 ай бұрын
Check continuity between speed sensor 2 and TCM body. See if the solder connects them
@rayjones347311 ай бұрын
@ryutech_automotive I have now sorted it it turns out it was a faulty pin on the tcu itself changed the pi and I'm cooking 🍳
@Amaxauto6 ай бұрын
Hi! Great job! Is it works with standard bmw software? Can I use this instead of programming the transmission immo?
@ryutech_automotive6 ай бұрын
Hi Max, this PCB is not to replace the stock TCM. This is to bypass the valves inside for the use of aftermarket controller, hence can't be used with standard installations.
@Amaxauto6 ай бұрын
@@ryutech_automotive Thank you! I understand now.
@luv_xxx27702 жыл бұрын
hi sir this modification for what
@digitalme44042 жыл бұрын
Question: Did you replace the 4 plastic rivets when finished?
@ryutech_automotive2 жыл бұрын
We put a dash of epoxy covering the used to be rivets, but it is not necessary because the plastic cover has a lot of latching locks.
@adalbertbusch70 Жыл бұрын
Qweston ZF6HP26 09E
@RS-lt2ue10 ай бұрын
@ryutech_automotive is there a difference in PCB between an HTG and a Turbo Lamik? The reasoning behind the question... Let's say, I'm using an HTG TCU, then decided to switch to Lamik. Will there be a difference between the circuit boards?
@turbowankel12649 ай бұрын
All the boards seem cross compatible
@RS-lt2ue9 ай бұрын
@turbowankel1264 thanks!
@michaellecompte18892 жыл бұрын
Do you like turbo lamik or HTG controller better? And why?
@BEYTEK2 жыл бұрын
Lamik imo
@piovo52222 жыл бұрын
@@BEYTEK why bro?
@maderpl1 Жыл бұрын
only HTG. Closed loop works perfectly. You can launch, do transbrake. Also HTG does frequent updates.
@adalbertbusch70 Жыл бұрын
Maybe you don't know ZF6HP26 Audi pinout wiring?
@Technical_Guruji5255 күн бұрын
Hii
@octocruz22462 жыл бұрын
Do you get any codes from doing this?
@ryutech_automotive2 жыл бұрын
It is for a standalone controller so it will not be compatible with oem functions
@user-gk9dp2ez3u2 жыл бұрын
피시비 판매 하시나요
@ryutech_automotive2 жыл бұрын
당신은에서 구입할 수 있습니다 : www.ryutech.co.th/product-page/8hp-pcb-for-htg
@fayobam_mech_tronics2 жыл бұрын
Can this be done for Benz 722.9 the control strategy seems simple enough
@ryutech_automotive2 жыл бұрын
Contact HTG Tuning for the control, they might have plans to add it in the future
@jdmtechllc65892 жыл бұрын
Can you do this for a 6hp?
@ryutech_automotive2 жыл бұрын
Possibly yes if there are demands for it
@jdmtechllc658910 ай бұрын
Demand
@stevekelly51662 жыл бұрын
Ooh this was painful to watch for many reasons. I've got one of these gearboxes. No idea what this modification is for, but I can solder, I'm an engineer, Painful. Use a toothbrush to leave any metal filings on top of the old circuit board? Mental.
@ryutech_automotive2 жыл бұрын
The fact that you have no idea what this is for; an 'engineer' would think about searching google for 'why' and try to understand complexity of modification rather than thinking 'painful' :)
@jdmtechllc65892 жыл бұрын
@@ryutech_automotive Brutal bro, he could be a bridge engineer right? Also his comment seems spur of the moment, and he just didn’t care enough to research. But I do see your point as well.
@ryutech_automotive2 жыл бұрын
@@jdmtechllc6589 The solder methods in the video might not be the best, nor using the best of equipment, the purpose of this is that installers (garage) can follow through with off the shelf tools. He does have a point for using toothbrush, but if you ever do the modification you'll know that it is quite frustrating to clean thoroughly.
@jdmtechllc65892 жыл бұрын
@@ryutech_automotive totally understand, and I know there’s a lot of white knights on the internet who never turned a wrench.
@ManpreetSingh-mn2lp Жыл бұрын
Can you please send me 8hp70 pcb
@ryutech_automotive Жыл бұрын
you can order them here: www.ryutech.co.th/product-page/8hp-pcb-for-htg