I'm so grateful to be part of this platform. Sir please i would like to request you that may you please upload the A.P.S schematic. I request
@RwihyaBenet-bh3hb8 күн бұрын
Very excited dear engineer. What of servicing the radiator, how to deal with it?
@RwihyaBenet-bh3hb8 күн бұрын
Great work sir.
@RwihyaBenet-bh3hb8 күн бұрын
Sir I'm confused with how the emergency stop cut off both of the two power sources. Is the neutral for both supplies combined before the ATS or some logic else.
@pikolomtn97248 күн бұрын
The signal cable is it from the battery to 8/7
@jkyalo79789 күн бұрын
Hi please,I appreciate your work.Can you please repeat the ATS or the Automatic changeover? A detailed explanation like you did with the star delta.Thanks
@electreca19 күн бұрын
I will do.
@kaundabwalya77769 күн бұрын
Well explained Sir 👍 God bless you 🙏
@jonathanmukilya87649 күн бұрын
Good work how can I see you, pin location
@samuelsackey7509 күн бұрын
Thanks
@seanakiiki767010 күн бұрын
I get ur explanation but the wiring makes no difference, more guidance please
@seanakiiki767010 күн бұрын
Engineer am not , therefore understanding the purpose of breaking btn the line supplying the main via the star auxiliary since u have connected it via the NC making no difference
@yasitharanga766410 күн бұрын
great great video sir. Thank you so much😍
@morrismaneae363411 күн бұрын
Can u make video of where i can connect my generator control cable to which terminal
@DavidRatemo-w7f12 күн бұрын
Provide us with the wiring diagram so that we may better understand
@seimela13 күн бұрын
Very Many testing b😂❤❤❤
@JJ-hw8ob13 күн бұрын
Well explained but use a thick marker pen
@JosephTono-j9s13 күн бұрын
Thanks engineer, I realy love electrica. Kindly share your What's up contact.....just if you don't mind
@danielteyehuago163313 күн бұрын
I'm here again. thanks for sharing this with us.
@danielteyehuago163313 күн бұрын
Do you have a video on how to settings the tripping current
@electreca113 күн бұрын
On overload relay?
@danielteyehuago163313 күн бұрын
I'm here again. Thanks for sharing this with us
@electreca113 күн бұрын
Thanks for watching
@zokonjazokonja14 күн бұрын
This method is only aplicable if both phases coils are same power (main and auxilary coil). If they are different power you could have a problem. And if auxiliry coil has centifugal switch like some motors have, than it will not work. I have such situation and I didn't found easy solution except to use Cam 1-2-0, four pole switch
@alemayehueshete648214 күн бұрын
please put the wire stap by stap
@electreca113 күн бұрын
Noted, thanks for watching though.
@abassembatya15 күн бұрын
Quick question, what is a comparator
@electreca113 күн бұрын
In electrical it device used for monitering voltages or currrent, by comparing the inpute values to the set one if the value are high or low to set one the circuit trips. Thanks for watching.
@CharlesSsenteza15 күн бұрын
Good morning mr david i need your email address
@CharlesSsenteza15 күн бұрын
Good morning sir, I would like your email address
@noelfaithfulkari285716 күн бұрын
No schematics?
@electreca115 күн бұрын
i will upload schematic on the blog, thanks for watching
@noelfaithfulkari285716 күн бұрын
Always likes your videos
@electreca113 күн бұрын
Thank you
@noelfaithfulkari285713 күн бұрын
You didn't explain the schematics of the ATS. Could you include it??
@danielteyehuago163316 күн бұрын
Please do you have a video on mechanical timer
@electreca115 күн бұрын
Not yet but will plan on it. thanks for watching
@danielteyehuago163315 күн бұрын
@@electreca1 Noted. Thanks
@danielteyehuago163316 күн бұрын
Always first to watch
@linossinkala784016 күн бұрын
Thankyou
@danielteyehuago163316 күн бұрын
I'm here again
@maxwellmanyinyire-by3gx16 күн бұрын
You didn't explain how to wire the control circuit
@maxwellmanyinyire-by3gx16 күн бұрын
You didn't show how to wire this. Can you show the wiring diagram
@gilbertjatauaugustine518317 күн бұрын
Thank you very much for this knowledge, but pls my question is exactly terminal in the Generator can I used for the auto starting and stopping of the generator when connecting my ATS
@electreca115 күн бұрын
Find a free NC contacct in the mains auto circuit, that will be your auto start. thanks for watching
@josephmaina205617 күн бұрын
How do you connect battery charge with the ats
@tshaunscales808617 күн бұрын
Thanks for the video. Great information
@mauriceomondi908018 күн бұрын
Hello, I am watching from 🇰🇪 Kindly help me with a wiring diagram of a bar bending machine. The machine has 3 limit switches, 3 contactors, and one start button switch, which is being switched by foot by stepping on it.
@breezerelectricautomations19 күн бұрын
The only problem is that you will be loading the transformer with only one phase being used at each particular time.secondly you will need a bigger size cable to supply the system with because you are not balancing the phases