Zeromode

Пікірлер

@SerhiyPopov Ай бұрын

Fck yeah! I did it! Thanks man!

@francescot.7320 Жыл бұрын

Is possible unbrick with Raspberry? Thanks

@zeromodefpv Жыл бұрын

I'm only aware of doing this using an Arduino. (4:08)

@stevanardilaacero4785 Жыл бұрын

en el ESC 1

@stevanardilaacero4785 Жыл бұрын

hola que tal como puedo hacer ese proceso en esta placa Whoop AIO F4 V1.1 Tablero AIO

@akkvik Жыл бұрын

Thanks! Just saved a bricked GEPRC STABLE F411 ESC with this procedure! It took a while to figure out which pads were Data and Clock but I enlarged the board with a magnifying glass and figured out where the pads was leading to :)

@zeromodefpv Жыл бұрын

Glad to hear that you have been able to fix it!

@bengordon7635 Жыл бұрын

I just received the Mobula7 . I binded went to fly and just flips esc no. 1 says yyyyyyyyyy-yyyyyyyy for the firmware the flash button doesn't work .. is it bricked

@Votec90CH Жыл бұрын

Han e Copter baut und syt em erste mol ahschliesse am Laptop zeigts mir keini ESC ah im BLHeliConf. Conecte chani aber gseh keini oder nur ei ESC D 4in1 ESC macht niene e Kurzschluss han en durre Piepst also glaubi nit das die Kaput isch ha s gfühl das isch e Flash Problem. Kei Komunikation umme zwüsche ESC und FC

@Votec90CH Жыл бұрын

Salüü, du bisch us de schwyz hani gseh chönsch du mir ächtsch bi was hälfe?

@alloutofdonuts3998 Жыл бұрын

Is there a way to do this without the Arduino? Pain in the buttocks it is!😅

@scissorzz 2 жыл бұрын

Hi, I a Mamba 50 amp esc and two motors aren’t showing after I reverted two motors and forgot to turn motor one and two back on. Now only 3 and 4 are showing how can I get them back ?

@jeromebyrd9813 2 жыл бұрын

how did you determine which of the pads go to which esc. ? I have been looking for schematic and I have yet to find one.

@KrotowX 10 ай бұрын

Find datasheet for MCU chips used in particular ESC and determine which pins are C2CK and C2D. MCUs here are marked with BB21 which mean EFM8BB2 in QFN20 package. By manufacturer (Silicon Labs) datasheet C2CK is pin5 and C2D is pin 6. With multimeter find continuity between chip pin and pad in a pad row on ESC board. Matching pads are ones which you must use.

@user-qk7fe9bh3g 2 жыл бұрын

Оценка 5!!+++) Я искал вариант когда не определяется ESC, но для запаса на будущее ОЧЕНЬ ЦЕННО!)) И вопрос? почему не захотели прошивать мавериком или JAZ??? Rating 5!! ) I was looking for an option when ESC is not defined, but for a reserve for the future VERY VALUABLE!)) And a question? why didn't they want to flash with a maverick or JAZ ???👌👍

@r.r.creation9491 3 жыл бұрын

Hi can anyone help I just brick one esc it would not show in blheli s any more it is babyhawk 2 hd board and I can not find thous pins to solder arduino I do not know if this board have them it is all in one can any one help please thanks

@erikvf7 2 жыл бұрын

Hey, just saw your comment here. I also have a BH2 and also bricked 2 of my ESCs while flashing the Bluejay FW. Strange thing is that the escs are working normal on Betaflight and motors are running all normal, however, on ESC configurator I can flash or get information from these 2 escs anymore. How is yours?

@matteogiaretta5818 3 жыл бұрын

Thanks a lot, my esc is revive 🎉

@zeromodefpv 3 жыл бұрын

Good to hear!

@alraed45 3 жыл бұрын

@ibex_fpv640 3 жыл бұрын

Wow thanks, it fixed my esc. I have flashed the wrong firmware to it and all esc's were gone. Can i ask wich Gyro Update Frequenz, PID Loop Frequenz and ESC/Motor Protokol do you use? I have the Tyro 129 with the same esc and Flight controller.

@zeromodefpv 3 жыл бұрын

Good to hear that the video was a help. I have updated to BF 4.2.3 and I use Gyro update frequency and PID loop frequency of 8 kHz, my ESC/Motor protocol is DHOST600 with Bidirectional DShot enabled. Take the settings with care as the quad is not flyable atm because of a power issue.

Ең жақсы KZbin

Пікірлер