Argh, I bricked a 4-in-1 ESC! How to fix this using BLHeliSuite and C2 interface | Eachine Tyro119

This video shows how to flash BH an individual ESC on a 4-in-1 ESC board by connecting the solder pads and flash it using C2 interface with BLHeliSuite.
While build the Eachine Tyro119 I flashed all the for ESC at once. Yet ESC number 3 had a problem while flashing.
BLHeliSuite: github.com/bitdump/BLHeli
JazzMavericks BLHeli_S 16.73: github.com/JazzMaverick/BLHel...
Bangood Eachine Tyro119: www.banggood.com/custlink/3DK...
Bangood Eachine Tyro119 replacement ESC: www.banggood.com/custlink/KKD...
Disclaimer: This is an affiliate link. I will get a small commission, when you use the above link - the price is the same for you.
Thanks to Joshua Bardwell for pointing me to the right direction:
• How To Flash BLHeli vi... at live stream • Q&A Livestream - Octob...

[@akkvik]

Thanks! Just saved a bricked GEPRC STABLE F411 ESC with this procedure! It took a while to figure out which pads were Data and Clock but I enlarged the board with a magnifying glass and figured out where the pads was leading to :)

[@zeromodefpv]

Glad to hear that you have been able to fix it!

[@SerhiyPopov]

Fck yeah! I did it! Thanks man!

[@matteogiaretta5818]

Thanks a lot, my esc is revive 🎉

[@zeromodefpv]

Good to hear!

[@ibex_fpv640]

Wow thanks, it fixed my esc. I have flashed the wrong firmware to it and all esc's were gone. Can i ask wich Gyro Update Frequenz, PID Loop Frequenz and ESC/Motor Protokol do you use? I have the Tyro 129 with the same esc and Flight controller.

[@zeromodefpv]

Good to hear that the video was a help. I have updated to BF 4.2.3 and I use Gyro update frequency and PID loop frequency of 8 kHz, my ESC/Motor protocol is DHOST600 with Bidirectional DShot enabled. Take the settings with care as the quad is not flyable atm because of a power issue.

[@scissorzz]

Hi, I a Mamba 50 amp esc and two motors aren’t showing after I reverted two motors and forgot to turn motor one and two back on. Now only 3 and 4 are showing how can I get them back ?

[@user-qk7fe9bh3g]

Оценка 5!!+++) Я искал вариант когда не определяется ESC, но для запаса на будущее ОЧЕНЬ ЦЕННО!)) И вопрос? почему не захотели прошивать мавериком или JAZ??? Rating 5!! ) I was looking for an option when ESC is not defined, but for a reserve for the future VERY VALUABLE!)) And a question? why didn't they want to flash with a maverick or JAZ ???👌👍

[@bengordon7635]

I just received the Mobula7 . I binded went to fly and just flips esc no. 1 says yyyyyyyyyy-yyyyyyyy for the firmware the flash button doesn't work .. is it bricked

[@stevanardilaacero4785]

hola que tal como puedo hacer ese proceso en esta placa Whoop AIO F4 V1.1 Tablero AIO

[@jeromebyrd9813]

how did you determine which of the pads go to which esc. ? I have been looking for schematic and I have yet to find one.

[@KrotowX]

Find datasheet for MCU chips used in particular ESC and determine which pins are C2CK and C2D. MCUs here are marked with BB21 which mean EFM8BB2 in QFN20 package. By manufacturer (Silicon Labs) datasheet C2CK is pin5 and C2D is pin 6. With multimeter find continuity between chip pin and pad in a pad row on ESC board. Matching pads are ones which you must use.

[@francescot.7320]

Is possible unbrick with Raspberry? Thanks

[@zeromodefpv]

I'm only aware of doing this using an Arduino. (4:08)

[@r.r.creation9491]

Hi can anyone help I just brick one esc it would not show in blheli s any more it is babyhawk 2 hd board and I can not find thous pins to solder arduino I do not know if this board have them it is all in one can any one help please thanks

[@erikvf7]

Hey, just saw your comment here. I also have a BH2 and also bricked 2 of my ESCs while flashing the Bluejay FW. Strange thing is that the escs are working normal on Betaflight and motors are running all normal, however, on ESC configurator I can flash or get information from these 2 escs anymore. How is yours?

[@Votec90CH]

Salüü, du bisch us de schwyz hani gseh chönsch du mir ächtsch bi was hälfe?

[@alraed45]

Hi

[@alloutofdonuts3998]

Is there a way to do this without the Arduino? Pain in the buttocks it is!😅

[@stevanardilaacero4785]

en el ESC 1