Use this to design Animations circle calendar clock

Great project 😊

Sir kya ye project stair light me bana sakte h

Very beautiful project

Please next project esp32-C3 4 channel relay module or fan speed dimmer add episode IR Remote rainmaker add Manuel switch

Very useful project 👍🤠💯😃😸

Sympa ce tuto 👍👍👍👍👍👍👍👍

how can i add this shematic 13009 mosfet for more power?

I want to ask about my line follower analog that is can not work, input+ is 3v and input - is 0v and the output is 0v how to can high mode

V.nice video driver card ups 24 volt ka card ki video banade apne pass

Next projector use microcontroller esp32-C3 4 channel relay or fan speed dimmer add IR Remote rainmaker app

Very good job sir thank you 💯👍👏☺️😊😌

Very useful project 💯 thank you Zen sir

Nice ❤❤❤

Good work, but video is bad man. Why did you show every step of connection?! Took like forever... ((

What’s the code in the void set up for the switch case part please?

Very nice 👍

Very nice. Can you make it so each light stays on until they are all lit up?

Bhai ye j1 kya hai aap k simple circuit digram m

Sir input voltage is given 230 V right

Nice project

Hello, please tell me what the AC frequency should be. I uploaded an Arduino code to the atmega8, but it doesn't run, and I set the internal frequency to 8mhz, but it doesn't run.

Please explain what you are doing with alligator clips. Also, I have always wanted to make a car trickle charger with 13.8 volt cutoff incorporated with the protection circuit. Such detail when it comes to putting the circuit together and it is so much appreciated. That is why I have subscribed. Thank you

I want without button and auto chaser😢

would be nice to see a PCB with Gerber files for these projects, they would then be useful, maybe a depository where you could buy and download them?

what changes it requires if i want to connect to pin3 of my 555 based pulse generator which is analog pulse i guess? kindly elaborate, Thx in advance

I agree with people comments about the Incorrect connections for load current sense. See LM723 datasheet fir details re how it all should be connected. Because of this fundamental design flaw the whole thing is useless , it is NOT a regulated power supply !!! Shall be removed from KZbin or fixed and then republished.

Title is english . Audio should too . English motherfcker you speak ........

Can we measure the value of ceramic disc cap 104 with this tester

parabems e obrigado

Hola amigo, gracias por mostrar tu círcuito cargador de batería, necesito hacer uno para una lámpara de mano 👍🏻👍🏻 bendiciones

Excellent Zain bahi❤

If I change mosfet so, input voltage increase?

Assalam o alekum bhai kia hal hai part 2 kb bnao gy

THIS CODE MUST BE USED WITH BOOTLOADER SET TO 16 MHZ. BUT THE PROGRAM BEHAVES ERATICALLY WHEN UPLOADED TO ATTINY85. WHAT DO YOU THINK?

the light still runing with or without pir sensor ?? i have try et 5 times??

YOU HAVE TO BURN BOOTLOADER FIRST SO THAT FUSES OF ATTINY 85 CORRESPONDS TO THE DESIRED FREQUENCY WITH WHICH THE CODE WORKS. I TRIED 1, 8 AND 16 MHZ BUT WITHOUT RESULT. DO NOT UPLOAD THIS TYPE OF FAKE VIDEO OR YOU WILL BE IN TROUBLE. THIS WARNING IS FOR ALL KZbinRS WHO UPLOAD THIS TYPE OF FAKE VIDEOS.

TODAY I AGAIN UPLOAD THE CODE TO ATTINY 85. IT ABSOLUTELY DID NOT WORK. I HAVE TRIED WITH 1 AND 8 MHZ.

Can you share project detail w me ?

I just realised that there is no 5V pin. How to I connect my VCC pin of PIR sensor to the Arduino PLC?

❤

Can you have the input be 12 volts and the RPG be 12 volts?In order to run it on the car

Circuit diagram