This is insane!👀🔥

🔥🔥🔥

I have an M3500. Mine had a problem work light loads and FTL, FTE. Here's what I did, and now it works exactly like it is supposed to even with the cheap 100 boxes from wal mart. 1. Cleaned 2. Replaced extractor and extractor spring (Benelli) 3. Trident trigger spring 4. Replaced firing pin sprin 5. Resembled using gun grease and ALOT of rem oil. 6. Rem ool in the magazine tube 7. Soaked the outer recoil spring tube to the point of oil dripping 8. Manually moved the action back and forth hard, about 450 times. At the very least, as hard as the 3 1/2 shells recommended to break it in. 9. Went to the range and it shot the light loads, ejected the affluent shell, about 5 feet, chambered the next shell 3 boxes of light load ammo to shoot 5 stand, and not 1 single problem!

Oh I see u replied I see how to take mine apart now it easy do it quick

1911's are for men. Welcome to the club 😂

If you bought a stoeger, congrats...you overpaid for a Walmart hatfield turkish shotgun.

🔨

This goes crazyyyy

Fire!🔥

Are you still using the Stoeger

Cool video. I'm looking to start filming goose hunts. What camera and lens do you use other than the head mounted gopro?

Sweet video!

Keep after it boss 👊👊 enjoy the rest of the season.

It was a blast

7:29

Who the hell wants to hunt with 20 guns in a spread?

Song? Lol

Fire

Banger

🔨

No, your intro sucked

ดาวโหลดไม่ได้ดูครับ

Is this a drop em video or a dive bomb video??? Nice hunt man bummed I couldn’t make it

Was a fire hunt

Need to invest in a SX4 bud lol

Dude please answer me on why my bolt is sticking after I removed the grease and oiled it up, its staying when I pull it all the way back and isn't pulling the shells out, nor cycling the next and just keeping it

Iron your flags.

The lucky lipper does it again 🐻 ⬇️

Getting after it bud! Congrats!

Great Experience Keep it up

Still need to figure how to take off the barrel I unscrew the mounting cap an that other nut what ever an it don't get loose

I got the stoeger p3000 it jam a few times

One of your problems is your shell tube should have a end cap in it.The spring shouldn't be riding against your screw on end cap

Where is this near

My m3500 won’t run migra 31/2 in. Stack loads. Crimp gets hung up every time on first shot. Tried a ported and non ported choke with same results. My friends m3500 cycles them no problem…. Frustrating after spending 300$ on a case

I had a kimber 45 acp once that would only fire CCI 230 grain ball ammo. Everything else would feed jam. Worst gun I ever owned.

I’ve shot exclusively Benelli semiautomatic shotguns the last 30 years. Biggest issue I’d have was slow action especially in the cold. It took me ten years but the First thing I learned is the Benelli oil that comes with the gun is no good for a lubricant. Take your Benelli and thoroughly scrub the action inside and out getting all. your old oil residue off the gun. Use warm water, Dawn dishwashing soap and a toothbrush and scrub thoroughly. Once everything is cleaned and completely dried reassemble and lube with only FP10 lubricant. I read that the military uses this when in arctic conditions on their AR’s. It’s cured all my cycling issues and I think I’ve owned nearly a dozen Benelli’s now. I’ve even taken quite a few of my friends Benelli’s after they where getting frustrated with their guns. They assured me they were clean. I’d say I doubt it and take the gun and clean and lube it like above. They can’t believe how much oil residue and dirt I get off the gun and how it resurrected their guns and made them cycle so much better and far more reliable.

I got a franchise affinity 3.5 elite in 2019 and it’s been my duck gun ever since only problem was when I threw it at a wounded snow goose and the hammer got offset and wouldn’t hit the firing pin, only hitting the right side of the bolt. Had to clean it to get it to fire again but no cycling issues yet

Jusy buy wilson combat mags

Remove the rotary head mechanism shackle pin of your rifle. It will not fit into place with the same precision and will shake in its bed. This is a design that should not be done in a firearm. It will never be a bad day rifle.

Jonny will shoot better

I think a lot of people assume the rust preservative is "oil" which is wrong. The preservative gels, gets sticky and impedes operation. I tell all my customers to completely clean their new weapons and use a REAL gun oil for lubrication during break in. Also, the Benelli M2 extractor & spring are a great fix for the M3000 with marginal ammo - I compete in 3-gun with the M3K.

From 30yards that grouping is very good dude! Thanks for the video looking to purchase one myself.

Pics

Does this apply to p3000? I got a p3000 and have jamming issues

If your jamming alot even after cleaning well, then replace the extractor and ejector and their springs. If you shoot alot they do wear out.

I have the M3020 i won it so... now its my my fav a lady from DU said to be sure and clean the shipping grease from the spring and tube and said it is on the turkish made models due to them being in shipping containers for weeks , and prevents rust etc . Its a protectant instead of a lubricant Mine works really well Mainly shoot Kent Bismuth

This spring is the weakest recoil spring you can make. I have seen carburetor return springs made better. It’s not just the spring, don’t buy these guns they are trash.

This problem is still on going. Maybe this gun is not worth buying. Just got a 20 gauge and jams even after a good cleaning. These guns are junk don’t buy them.

It’s not your gun it’s all Stoeger semi autos