hello can i message you directly? and can i ask some help
@AlfredoRodriguez-kk1il4 күн бұрын
Maravilloso video. Tengo una pregunta para usted, como se calibra el sensor de imagen? Un saludo y gracias
@9010Media6 күн бұрын
Thank you for making this video! Can you identify the part number of the part you replaced?
@igor_laprado13 күн бұрын
Hello, do you have suppliers for the flat cables for the Samyang 24 70 lens?
@RONIGLAHN13 күн бұрын
The best vídeo ever even that stupid music playing aloud in the background. Thanks from Brazil
@CameraRestore2 күн бұрын
Thank you, greetings from UK!
@THEREALWDJ22 күн бұрын
Excellent!
@CameraRestore2 күн бұрын
Many thanks!
@ianmclyde22 күн бұрын
Hi, what are the 2 flex cables at the bottom of the main board called? The large one and little one below the image sensor flex cable. Mine are broken so need to find replacements. Thanks 😊
@CameraRestore2 күн бұрын
Hi, one is PCB to bottom board FPC cable and the other one is the lens contact FPC coming from lens connector. I do have them both in stock, if interested drop me a mail at contact[at]camerarestore.co.uk
@jofifpv22 күн бұрын
Hi! After switching on my 100D (~15-20 minutes after being switched off), it only takes a completely white picture. It doesn't matter if you save as raw or jpeg. I tried several lenses and sd cards. I adjusted all the parameters and updated the software. It does this in all modes until I switch to live view. Then suddenly it will be good and then it works perfectly while I use it, but after ~15-20 minutes of inactivity it is bad again. Then I have to switch off-on, than to live view again and then back. I can't imagine what the problem could be, where should I go, what should I check first?
@muttBunch27 күн бұрын
This is awesome, it's close enough to my T3i model. I have a bad habit of leaving the SD card in the slot, even when not in use. I'm assuming, over time, that is now a "no no" as I fired mine up after about 2 years of the SD card being in it and when I tried to remove it to throw in my laptop, it gave me trouble getting it out. It took a little force after the eject mechanism but it still gave me an issue getting it out. A piece of the corner from the SD card was cracked and created an obstruction. When I finally got it out, I learned that it bent the contact pin for the write protect lock and no matter what I tried, even though 6 different SD cards, didn't have the write protect lock enabled, it still would not read the card. Just ordered my SD card board and when it arrives, time to go to work :D
@CameraRestore2 күн бұрын
Hi, thanks! Interesting, this model had some issues with the SD card, same issue as you mentioned. You are lucky with this model, Canon decided to place the SD card separately on this entry level camera! This is my first video on this channel, it got over 22k views by now, glad to see people still can make use of it!
@zetacrucis681Ай бұрын
Fantastic but completely skipped the part I was interested in: the AF sensor and adjustment mechanism behind the mirror.
@CameraRestore2 күн бұрын
That is something that cannot be done by guess, only the manufacturer has the tool for that assembly. I rather prefer not to talk about adjustments on the channel that I don't have tools to adjust.
@zetacrucis681Күн бұрын
@@CameraRestore Thanks. There is confusing info online about that: some claim they could tweak one of the screws with an Allen key and get AF spot on, some say it's way more complicated and you shouldn't touch it. Luckily after disappointments with the same viewfinder-AF issue on D3300 and D5200 (that full frame cameras have AF Fine Tune for), I found a D3300 that's spot on. Very handy low-light two-camera setup: a lightweight DX camera + 85mm prime alongside a standard zoom or prime on a full-frame (D3300 + D600 in my case). Or wide on FX and 50mm on DX. Btw. I took it to reputable repairer and the AF adjustment would have cost more than buying another camera.
@WestcoastpedalboardАй бұрын
Do you have a screen link?
@CameraRestore2 күн бұрын
Did you solve your problem? I have the part if interested.
Thank you very very much!!!! It worked for me with the exact same products. Done on a Nikon D3 and became like brand new with vivid black color and no stickiness!
@Meth0zАй бұрын
Another question.. what brand are your tools? i keep buying terrible screwdrivers that just damage my screws
@Meth0zАй бұрын
quick question... i bought a used 5d mark ii.. with fungus in the pentaprism.. is there a way to get to the pentaprism to clean it?
@loven-photographyandproduc7335Ай бұрын
Hey, Where can I get part of the black ring? For me it is already completely broken
@igor24gАй бұрын
Дякую за відео! В мене D3s теж відмовився вмикатися. В сервісі відмовили, бо немає запчастин. Після перегляду цього відео я купив плату живлення на алі, і самотужки замінив. Усе працює!
@CameraRestoreАй бұрын
Hey, that is great, I’m glad you managed to sort it out!
@marcinziolkowski413Ай бұрын
Mój d2h też nie chce się włączyć,czy są do niego dostępne płytki?
@igor24gАй бұрын
@@marcinziolkowski413 пошукай на алі експрес плату з назвою наприклад "плата живлення"
@johncarlosalangsang6511Ай бұрын
Hi. I hope you reply to this comment. May I know what capacitor does the XE2 have?
@HiagoOvictorАй бұрын
Part2???
@alwynsmit35462 ай бұрын
How does this build quality compare to a Canon mid range for instance?
@CameraRestoreАй бұрын
Quite similar I would say
@alwynsmit3546Ай бұрын
@@CameraRestore thanks for the response.
@TheSktch2 ай бұрын
yesssssss!!! I fixed my 35mm. 100% restored!!!
@CameraRestoreАй бұрын
Nice work!
@wcleong55842 ай бұрын
Very detailed. Tq
@user-vl6gg9kh9u2 ай бұрын
Very good vidéo. Thank you.
@royshroud95362 ай бұрын
Thermal image can help identify shorts even at low power.
@CameraRestore2 ай бұрын
Yes, very aware of, next tool to add into my work bench 😊
@TOPEC2 ай бұрын
Hello there, I noticed you mentioned the dc/dc board may need repair/replacement, are you able to provide the picture again where I can measure the board with a multimeter so I can test? Reason being that I have a 5Dii that will not respond to any buttons. Power switch will no response, cannot turn on/off. If I change the switch to on/set then insert the battery, it will power up the rear screen but not the top screen. The rear screen also has a faint overlap of 2 different menus which makes me think there may be a short somewhere. If i use something to hold down the battery door switch along with setting the power switch to on/set and then insert the battery, I will get the initial date setting screen, but again, no buttons would respond. I have changed the internal button cell and also opened up the rear cover and checked the ribbon cables, all attached and no damages, so I suspect it may be the dc/dc board? Thank you in advance!
@SkumleRafte2 ай бұрын
Did you ever dissemble this lens down to the optics?
@CameraRestoreАй бұрын
Nope, sorry…
@yogimis2 ай бұрын
Hello ! Can you give me advice on Nikon D4 ? Displays low battery on the top screen. Is it a damaged DC power board or rather mainboard?
@CameraRestoreАй бұрын
Could be multiple points, still, doubt is any motherboard fault.
@DabblerBabbler3 ай бұрын
at 57:50 the second switch that you refer and the metal part it's also the device that keeps the communication between body and battery, right ? After replacing some batteries, I still have no communication with the battery with this canon 5D MKII.
@HugoMartins-kf5wv3 ай бұрын
at 57:50 the second switch that you refer and the metal part it's also the device that keeps the communication between body and battery, right ? After replacing some batteries, I still have no communication with the battery with this canon 5D MKII.
@zoranbosnjakovic91553 ай бұрын
can the old model of the base board be replaced with a new model of the base board, with the replacement of dc/dc, please answer, thank you
@esquilo7773 ай бұрын
Hi @CameraRestore, just one question, please, if you see it, that is. If not, no worries! One of my D700 (SN 24), anytime we put it OFF, will loose some settings, will come alive always with "P", as Program, and the shutter count returns always to zero (0). It holds the time / date. One don't even has to take out the battery, simple putting it from ON to OFF and if again, ON, will happen. Any idea, please? Main condenser, PCB...??? And Many Thanks for all the work that you put on your videos. Cheers!!!
@zoranbosnjakovic91553 ай бұрын
Canon 6d m ll replacement of the old base plate with a new model,with the installation of a new version of dc/dc power board, is it possible
@raymondchan35873 ай бұрын
My problem is the internal flash CLS not working in CMD to trigger remote ( off-camera) flash.
@AAhmed_Alii3 ай бұрын
Incredible!!
@mdam22543 ай бұрын
After I shoot a few images or a few seconds of video I get a error 70 or error 80 any idea what the defect is?
@wiseredragon4 ай бұрын
Very cool video. My 100D keeps freezing when ever I switch from viewfinder to view the subject on the touch screen. Or even if I just view an image that I have taken on the screen. I have to remove the battery to reset the camera then it works again. But if I just switch it on, I can use and make changes to the settings pages using the touch screen. Could this be an internal memory issue? The EOS D100 is EOL now and Canon South Africa say they do not support it and cannot repair it as they have no parts available. PLEASE HELP.
@douglas_hifi4 ай бұрын
Hello! Thanks!! Is it easy to reach the microphone of a D7200? one of mine just makes noise...
@AnthonyCelata4 ай бұрын
Hey, love your video I'm using them to try and fix my camera its a 70D that has no power. Checked the obvious things like the door switches and stuff. Nothing lights up, power switch seems fine, no physical damage anywhere, and I have voltage throughout the whole camera. But nothing turns on. While searching the internet for answers I keep coming across a chip with "M04" written on it. Do you know anything about this chip? What it does or how to test it?
@shacklemanwarts13054 ай бұрын
Hi, this is a really good video, I watched other video but they are not as good as this one, you narrative the way through the process, having clear age with good perspective on the work. Well done mister
@sarahobsidianphoto23054 ай бұрын
I would LOVE to see a video on replacing the viewfinder assembly on a Canon 5D Mark IV or similar. My viewfinder glass broke and I don't want to pay $600 at Canon to repair it.
@benbunch41594 ай бұрын
Does anyone know if the rear element can be removed for cleaning with just those three rear screws after the PCB is out, or do all those screws he removes with aperture etc have to be removed first? EDIT: yup you can just take it out.
@zoranbosnjakovic91554 ай бұрын
Canon 6d m ll replacement of the old base plate with a new model, is it possible
@barathneymar35344 ай бұрын
Sir one week before i shoot with nikon D 700 in continuous shoot...Camera had stuck to buffer picture to load... suddenly switched off...then didn't switched On again.. Battery gone..now replace new battery still didn't turn on sir... kindly guide me
@mcqueengraphics49734 ай бұрын
Hi, where did you buy the replacement screen? All I’ve found for mine is in Ebay and they’re $700 which I find to be extremely heinous.
@WalterWuSG3 ай бұрын
I found mine on Taobao for USD$36.Excl shipping
@doksdavaudoo90754 ай бұрын
`thank you. great video, i used it to change the lcd....would have been a hassle without you
@MadFaker4 ай бұрын
HI iwas not able to get the screw in the dial the dial will rotate when i turn the screw its like the dial and screw are stuck together
@jeltevissertje5 ай бұрын
perfect guide to replace a broken led screen!
@billo55 ай бұрын
Amazing video thank you! Unfortunately my Xe-2 internal battery is dying so i have 4 seconds to change the main battery before all my settings default to factory. Do you know what internal battery does the Xe-2? Can't find any information. Thanks in advance!
@sn0rbaard3 ай бұрын
Did you ever find out?
@billo53 ай бұрын
@@sn0rbaard no, in the end i just returned it. it was already soo expensive for a 10 year camera, so it didnt make sense to keep it and open it up.
@ThePoplord20105 ай бұрын
Hello, I have the same lens, but I have a different problem, which is that the zoom starts at 28 and not 24. What is this problem and how is the solution? Thank you.
@kchappelle5 ай бұрын
Did you ever find the right top circuit board?
@CameraRestore5 ай бұрын
Yes
@kchappelle5 ай бұрын
@@CameraRestore Where can you get parts. Like circuit boards? I may need one for a D4S I’m repairing. Thanks.