Fuck KZbin ads and devs.

Fuck KZbin ads and devs.

Thanks alot 🎉

Fuck KZbin ads. 3 ad breaks in 7 minutes. Pathetic. Greedy.

What gauge is the fire alarm wire (red wire)?

Are you available for FSD switch wiring questions?

Nice video

Could you explain further the "top 15% ceiling height requirement"?

Thanks for posting these videos. Going back around studying the NFPA 72 section right now, and these videos make it easier then just trying to read that dry book.

How do you connect the HVAC shutdown wire to this setup

Great vid really well explained 💪

Is the code similar to California ? Cause you explain this great and it’s helping me out understanding it. I take my FLS soon and this is good stuff

What do i need to do to program this panels?

I’m going for my lvl lll,, I’m struggling with the math on how to space smokes ie,, what is the math for a room 30’X30’ or 250’X100’ ,,, I haven’t grasped it yet,, idk why the light isn’t clicking

Why does the pull station need to actuate the maglock (in your theoretical situation) directly? If the fire alarm goes into alarm, shouldn’t that automatically disengage all access control locks for the very reason of not trapping people?

I was searching for such information...not available anywhere else

They were not specific on distance for air handlers for larger than usual returns and supplies because it would depend on the rate of air flow, the direction and the manner in which the air is manipulated

I am new in this field

Good morning.please,which part of the building is the green cable wired to?

How do you connect three tamper switches and water flow to bell

Just moved to Texas and looking to get licensed in the state.. do i need to be employed by a fire protection company to even apply for the testing?

Excellent video

I have an ERV unit that needs 4 smoke duct detector 2 of them are for supply and return. I am clear about the airstream with those. Then I have one for exhaust air and the other for outside air. I am not clear where to face the sampling tubes holes on those. Can you explain how and why please.

Pls can you do a video or connection diagram of how to interface DRN to shutdown AHU?

Occupancy "I" is Institutional not "Industrial". Type "F" is factory which is the closest thing to industrial.

How do I interconnect two of these

How do I interconnect two of these

if I have a ceiling 90 by 90 with 28 feet high?

How many duct detectors can be installed in a loop.?

I wanna Congratulate You guys for such superp videos . You guys are the real Deal !! The Best videos on Fire Alarm Systems on KZbin PERIOD !! No one comes even close . I learned and enjoyed watching every single video you posted so far...

Why do fire alarm transformers get so hot to the touch and hum so loud. Is it normal? Have a Fahrenheit IFP-75

Thank's for your advice!

Thanks for advise!

Thank you very much for n my case is a fire suppression system in a commercial kitchen. When the system is activated the pressure switch should send a signal to the solenoid valve to close. In this particular kitchen the solenoid is connected to the gas detector. Shall i connect my pressure switch directly to the gas detector?

Great video. Great job explaining it to the audience.

Great explanation 👍

what do I look at for smoke detector requirements for commercial spaces?

This is great. Anyone should watch this to know these basics yet new to so many. Great job well done

Great video. Just out of curiosity, what is the code on requirement for holes in the sample tube for a 22 inch duct?

Thank you for this video !!! Anyway we can get that PDF you’re referring to ? I have my test coming up soon and am hardcore studying

Have you ever ran across an audio chain fault?

Do you know who how to monitor battery power loss ? . I know the ac trouble if for the 120 power idk how to monitor the batteries

Best explanation I’ve seen. You just made it simple, thanks!

Thanks for posting. What's the difference between contacts 1 & 2 on the addressable relay?

Can you mount a duct detector inside the air unit at the beginning of the supply?

Do we need to order EOL resistors separately or they are coming with power supply? And if yes, then of what value and how many? Can you please help with this? Thanks in advance.

que voltaje puedes utilizar con el modulo relay en nc o no

thank you , great video

Thank you , great explanation