It seems like the oil heaters are a deception. They probably only put out about 600 W. And they all have basic on and off switches like you’re too on and off switches. If you just turn one on it probably is just a light switch or an on and off switch. They simply just have power going out to the thermal coupler and then to the thermostat, that’s it.

Thank you so much! This tip worked perfectly!

Who reads the directions?!?! 😐 My heater wouldn't light, turned the regulator down as you showed, and now we have heat! Thank you.

Worked perfectly for my 7740 Office Jet. Thank you so much!

seems like I might have found this a tad too late. I downloaded the downgraded firmware for my Officejet pro 7740 and it won't find the printer to apply it to.. so so sad.

Don't do what this guy said, and if you did, put it back to the way it was! If the pilot light goes out, gas will keep flowing into your house!!! The way to fix this is to look at the probe(not the sparker) the pilot light flame is blowing over. If while holding the pilot light button down(with the flame going), the flame should be hitting that probe. If the flame is not reaching that probe, then turn everything off and and use an air duster can to blow into the gas line(debris most likely is the line from not using). If the flame is hitting that probe and the pilot light is just not staying on, get some sand paper and lightly go over the probe to clean the build up off of it. Then everything should work like it should! (no offense to the video creator! But please do an update showing how to just simply and safely clean the probe!)

After 2 years, still helping! Thank you man.

Thank you! If you are on a Mac, switching to Bootcamp and installing via the WIndows driver works fine.

How would I do this on Mac OS sonoma?

My bf bought one used and we can’t set the temperature. When I push the left button with the thermometer on it nothing happens. Can u show me how to set the temperature?

Your lucky that you have a nice instructor because mine was a pain in a ass

I thought this sort of thing was Illegal?

Have the same boat in a 13' SS, but getting way more than 34 MPH with a 40 HP JohnRude trimmed up. Doing more like 42-45 WFO.

🤣🤣🤣🤣🤣🤣

Just buy the ink and drip it into cartridges. You have to wait a day until ink drips into printer but it’ll work better even than with new cartridges.

Thanks - I was able to get the downgrade installed and my old cartridges work great. Disable updates and saved money. Much appreciated

Super helpful video, thank you!

HP sucks

Thank you for posting! I know this is an old video, but it saved my butt today. I will never buy another HP product, EVER!

A bit old, but you can block Internet access to the printer within your router to prevent auto updates if you can’t do it at the printer, or the printers web interface. It doesn’t need Internet to function on your home network.

I was having the same problem. Ran a jumper wire, left, it hooked up. Ran a jump wire between the 2 wires and it works fine and if you tip it over it still shuts off. In case I don't help any buddy still has safety features

I was having the same problem. Ran a jumper wire, left, it hooked up. Ran a jump wire between the 2 wires and it works fine and if you tip it over it still shuts off. In case I don't help any buddy still has safety features

I really appreciate the time you have put into this. But how much effort does it take to link a photo or pdf to a wiring diagram? If you want to help, why make it a game.

Does this work for snowplows? If so which one do I buy winter is coming up I’d like to throw on on that same tractor I have but can’t find any that fits

Thank You sooooo much!

What happens if you dont have an OS laptop or phone!

I thought I had found the downgrade firmware but it's all for Windows and I have a Mac!

Thanks so much dude my 1977 cb750k gave me problems on my way to school and if my ignition keeps being stupid this will save me the embarrassment of calling someone to pick it up

After trying lots of other suggestions, you saved the day! This worked perfectly--thank you!

This worked beautifully, except that then the printer told me I had cartridge problems with my black cartridge (only). I was able to pop out the chip from another 3rd party cartridge that worked previously, and switch it into the new full cartridge. That worked!

Thanks for the video. I didn't see how the back of the undercarriage supports the blade frame in the back of the tractor, does it just hook on?

Can I do this in hp t830 plotter

Israeli company boycott it

Super fantastic. Thank you! Had the same issue but was intermittent and might stay lit if I held the pilot on 4-5 minutes. Essential worthless. Bought a new pilot/thermocouple to fix thinking it was the thermocouple, but discovered it was going to be a major project to replace and found your video. Could not see any corrosion but a little emery paper application and working like new.

You need to do a proper top balance at 4.2v then try again. Those small shits ain't doing anything except scream. Get a proper BMS or those 5 - 15A active balancers that you can turn off below 3.9v or so

Arent those Gen 3 cells ? Got Gen2 in 14S20P from 3 Leafs, Batrium WM5 BMS, no need for a balancer on every cell. The WM5 or others balance with 5A or so, thats too low for 14S20P, but cell drift after nearly 4 years is fine, 10mV at idle. It matters where to locate the cable on the bus bar when having multiple in parallel. Voltage will then vary under load due to bus bar thickness

Thank you so much. Over the past number of years I’ve had five of these heaters fail. I couldn’t bring myself to throw them away. I just used your tip over bypass alteration on the latest one. It worked perfectly. Now I never have to buy anymore 👍👍👍👍👍👍👍

good thing the suspension works without the controller just always open.

PERFETTO -------CAPOTE NON FUNZIONANTE ADESSO TUTTO OK......GRAZIE DEL SUGGERIMENTO-------TUTTO PERFETTO

This worked for me and my 6978 printer. Thank you so much! This will save me hundreds of dollars a year!

What is the better choice for a new printer. I have the same issues and just want to throw this one off the roof and never buy HP again. I need a printer scanner for 10-15 pages per month. The 100 spent in cartridges dry out after a few months

Omg just cut to the chase brother , we don't care about all that xtra shit

Does anyone know where is this place?

I didn't know they take walk in, it's so hard making an appointment online.

Lobe the video but would love to know what size the bolts are

So it can actually be downgraded by doing an update. Thats interesting. Usually rollbacks don't work... at least on android systems as far as i heard.

It's so crazy. The world is so busy to forbid plastic straws. But in example when its about printers especially HP the waste of material is insane. There is so many complaints about customers that they even don't want to buy an hp pronter anymore. For me the same. I will never buy an hp printer again even if the old one is good but the amount of ink it blows through the pipe like afzer every clean that tales ages anyway the ink even it its a XL ink is pretty half up to full empty afterwards. Does anyone know a nice reliable printer which doesn't burn the ink through öike hp? Where third party cartridges are not a problem?

Nice! The bearings in that draft inducer sound horrible though. Eventually that thing won’t be able to turn fast enough to close the pressure switch anyway.

Same issue, and this worked perfectly for me, 9 years later, your the man, thank you!

Thanks for the solution.