Didn't even let it fill out, went to fast

Make it do or do witout

Run what you've broung

Trust your eyes

Best photography yet

Do I use 6013 for metal like that I'm building a gate tomorrow?

Every1 welds so differents its truly an artform but the outcome is usually the same which is baffling to me

Thank you

I really struggle to do this weld

Электрод 6013?

Just get yourself a MIG for doing stuff like this.. easier and cleaner.

❤

Толстый металл каждый лох заварит. Вы заварите 1,1 мм.

Oooooouuuufff 😍😍😍😍

Hilaw ang welding 😂😂😂

i use 60amps on 3mm metal with 6013/2mm works wonderful with correct drag speed u just need to practice 5-10 passes to get used to it, but anything under thick is pain to weld cuz electrode won't start under 50 amps & over 50 amps it make holes. i think tig or mig welding is better suited for thin metals

How many welders does it take to change a lightbulb? 10! One to change the lightbulb… and nine to tell you how they would’ve done it better

Sehr schönes Video!! Spitze!!👍

My beads youse to look like that recently got back into welding loving the content

Parabéns ao vídeo.

Yo what is that travel angle 😂

Nice video ❤

Bang kmera bisa jelas pake apaan? Hp biasa?

Pas de balayage haut/ bas !!!😡😡😡2.5 est passe partout !...

Why you didn’t show the heat line on the opposite side of the metal? How can I understand that you welded up the details. Now, I see the thick rod (that means lower temperature) and I see to many movements. So you just stick the welding metal to the surface? To understand it - we should watch at the other side and see the grey line on the joint where details need to be welded together. If there is no light-grey joint - it means that our construction just sticked together like with a glue

Bonsoir merci

Hi, what amperaqe was the machine set to, was it DCEP ?

Супер

May I know your using welding rod what size & brand of welding rod?

You need to take up knitting.

Всё зависит от сварки и от электродов, хорошими электродами заварит и новичок, плохими не заварит и спец

Clean the metal up???

От себя надо варить, а не так. Сварщик блин

Мог бы озвучить😢

Ya los quisiera ver soldando en estructuras en techos con el viento en contra

Попадается хорошее видео, после того как ты приварил 😂

Not good you are new walder I am also walder

Ну что варить 3-м способом? Первые два отличные для всего.

Норм.

Srick welder? Nobody uses those anymore.

Walding good but this is normal join stred walding

Try doing that in the boom of an excavator. I'm doing that in the boom of a Komatsu PC12O LC Excavator that the bottom of the boom near the pin cracked all the way around and only half of the boom on the cab side is attached and half of the back of the boom on the cab side attached. It's a major repair. I'm welding the cracks then grinding it flat and welding 1/2" steel plate over it for the bottom boom and the side opposite of the cab but first I cut out a window with the plasma cutter so I can reinforce the inside of the boom then weld back the window and put a steel plate over it also. The inside of the boom there's a blind spot where I cut out the window. I need to weld that part. I'm going to put a mirror on the opposite side and look at the mirror while I stick weld the blind spot. That's the only way I can see what I'm welding. Space is tight in there and I have a hard time maneuvering the rod. I'm burning the rods halfway and saving the rest for other areas. Been working on this for over a week already making templates for the steel plate to cut and whatnot. Everything is in the way so it's a pain in the ass welding and trying to see what I'm doing. I'm making videos as I progress and will put together all the clips into one and upload it. I forgot to video how the crack boom looked before I welded it because I was too busy trying to pull the boom in place with another excavator to get the crack close enough to weld and the boom straightened out. And my boss was watching so I couldn't pull out my phone to record.

Автор не все професионалы. Выложили видио,естественно будут вопросы. Мне надо 2 машины подварить .сварка естественно не подайдёт. Мне легче купить оборудование и научится,еще и деньги останутся. Вот такие как я и будут задовать вопросы.

Azul Bravo pour la dimanstration

Parabéns por nos ensinar.

Os teus pássaros têm lindos cânticos.

Tu és muito didático, parabéns.

On the wood !!🥱., why not?

As someone who taught people to weld, I can say only this. Anybody can weld, but not everyone will be a good welder. Practice, as the saying goes, makes perfect.

Как и в любом деле, в сварке главное набить руку. А иначе могут набить морду 😅