I'm looking for a larger piece of wood and I love the one you used. Mine are 12" x 12". Can you tell me where you bought the sheet of wood used in this project? And what are its measurements?

Wow...Thats a beast. 130 watts is some serious cutting power

Hello, awesome work and great video! You could try using an airbrush machine to paint it-it might make the process a lot easier. All the best with your project! 🙏🏼🇵🇹🇧🇷

ahh the infamous Hrbr Frt FR clamp gray rubberized gray limited yet cheap/ I say use 2x8 Wood I beams that has formica faces and or overhead dropped platform

Unplumb walls are SUPER annoying. A house should never even get final sign-off until walls are plumb... unless they were designed to not be, of course.

How do you hang them up ?

Awesome Thank you

Thanks for the video. Very helpful walk through. How tall are the female brackets? I'm curious how wide the mortise needs to be. Looks close to 2 inches but the site doesn't say for some reason. I know the make a slim version now. Not sure how big those are either.

Love it!

Very nice!

Ciao, che tipo di carta hai usato per coprire i pannelli? PS. Bellissimo risultato!

Do you still have the v-3000 and did you receive potential safety issue notice from Oneida regarding the bolts that secure the fan to the motor on the V-3000?

Go Navy. Am a RNLN vet myself, 36 yeard, now retired since 2013, and just bought my sculpfun s9

Beautiful piece of work!.

your audio cuts off at 4:22

EXCELENTE SU TRABAJO. FELICIDADES!!

Is the maple end grain or long strips?

Absolutely beautiful work! I was so inspired by this piece that I made one. The small strips of wood were made from black walnut and I used ash for the contrasting color(s). When it was done, my wife insisted that I enter the cutting board in the Ventura County Fair competition. I did and the cutting board took 1st place...thanks

Beautiful! Where can I find that file, I would love to try it.

They look really nice!

Just stumbled on to your channel, nice work. Looks like a lot of time making these. How much are you asking for these?

AWhy don't you cut each piece without paint and without masking.....and paint them later with spray paint?....and glue them later....to me this way is easier and faster

Good job 👍

Thanks for the helpful video. I'm needing to do my first set of floating shelves, and yours is the best non-marketing video that gives the pros/cons of this system.

A cinematic masterpiece! I was utterly captivated from start to finish.

Hi there. Great vid. I've looked on Amazon, but can't find tinted stains like you have...

I bet several of these or like these joined together would make a gorgeous club table or dining table. Or even kitchen counter top. But the amount of time and craftsmanship put into it... Man, you have my greatest respect!

another question: Is that a sliding attachment to the table saw? Can you share more info to it?

this is really a piece of art! quick question: how essential would be it have a drum sander? I wanted to build this pattern but just hesitant due to drum sander. Dont own one since dont have the space for it.

I'm sure it's in the comments somewhere, but electrical super strut is more rigid, and it's got holes for 1/2 inch carriage bolts. About $40 for a 10 foot section. I got two, and made three pairs of 40 inch cauls. I put a 6 inch bolt with a washer and wingnut on one end and clamp on the other. Thanks for sharing!

Muy hermosa amigo, lástima que lleve tanto tiempo en desarrollarla.

thanks for your videos! and congratulations a consulate where you get the designs I am from San Juan Argentinian, it is very difficult for me to get them THANK YOU If you can share what I get I will share it with you BLESSINGS

Can't seem to have hypersonic missiles without belief systems, you noticed that too?

So nice work how to download file

What masking do you use?

These are not ideal for shelves inbetween walls that need scribed

I just received my laser a couple weeks ago and I dido @scottmurphys I could not have asked the same thing any better. Thank you for great content and sharing.

I prefer Tung Oil over Mineral Oil simply because Mineral Oil and anything using Mineral Oil, never fully dries. There is always a slight dampness and liquidity and each time you put food, especially meat, on the cutting board, some of that mineral oil gets into your food. Yes the FDA says it's safe but would you trust a government with a vested interest in you dying before retirement age?

What laser do you have? I have a xtool d1 pro 20w. And how do you design your art? I’m interested in creating and not just grab files from Etsy.

Fanstastic job and project! Thank you very much!😉

So after a year with the 130W what do you think? Worth the investment?

Love it! <3

inch/imperial system so stupid 3, 4, 5, 6, 7, 8mm - more easyer.

Since KZbin got rid of PMs, I will try this and hope you are still keeping an eye on things. First, great video, I really enjoyed watching. Second, it seems that the link for the design is no longer valid. I am getting my first laser this week and would really like to try this design once I have kicked the tires a bit. If you see this can you reply with a new link? Thanks for the content! ~Scott

Hi, everything is brilliant. I just failed to understand how you got the cross separated to different layers. Would be thankful for some insides.

Wouldn’t it be better to spray these multiple layer projects?

Those are a great idea for caul clamps. I'll have to make myself a set. In the past, I left my caul clamps in place until the glue sets. Wet glue is like a lubricant and can allow the wood to shift until it dries.

Beautiful

Gorgeous!!

is there generator software to create the layers out there that is free?