Hi, Great Video! Apparently my G29’s Motor is stuck on the transaxle. Do you think I can do this service while the motor is still on the transaxle? I am sure the springs on the brushes would be the biggest headache if I try to do it without removing it. Also any tips on removing the stuck motor from the transaxle?
@backshed52953 күн бұрын
no mate you cannot do it any other way, i have done 100s and never had 1 i couldnt remove, why are you thinking its stuck? check you haven't missed a bolt
@daverhaci63692 күн бұрын
Thanks for your prompt response! All the bolts are out. The casing spins freely. I used all kinds angles to pull it out but it doesn’t budge. I am guessing it might have got moisture inside and rusted inside the transaxle where the motor connects. I am thinking of removing the casing and see if it is rusted at the connection point and go from there. I would appreciate if you could let me know if you think of any other method to get it off the transaxle.
@backshed52952 күн бұрын
@@daverhaci6369 ive never came across that. You may as well keep trying though , spray some penetrating lube or something in the direction of the shaft . You wont have room to slide the case off the armature sideways unless you remove the complete axle from the cart
@daverhaci6369Күн бұрын
@ I was able to get it off after 2 hours of constant prying in between the casing and the transaxle housing last night. It finally came apart. It was rusted bad inside. I put the bolts back on and left them loose . I used a small pry bar and bunch of metal plates to close the gap in between the lip of the housing and the casing. I kept prying by pushing on the bolts with the support of metal plates until I had enough space to insert my pry bar in between. Who ever does this job needs to put on safety glasses for sure. That carbon dust came out from the casing after the motor popped off the transaxle was all in my eye. You were absolutely right. That little motor was very heavy. It felt like benching 300 pounds while trying to put the motor on the ground. I will try to upload a video soon. Thank you for your encouraging comments!
@backshed5295Күн бұрын
@ all good mate👍🍺
@daverhaci63693 күн бұрын
Great Video! Is there a trick to get the motor off the G29 after you get the 3 bolts out. I can seem to get it off. It keeps spinning.
@fixityourself111Күн бұрын
@@daverhaci6369 its heavy as heck you need to lift as you pull👍🍺
@josephkryzak33314 күн бұрын
Clucking noise while backing up on club car
@Ben-ki5bf13 күн бұрын
Dude love watching your vids and cars I’ve just got myself a Yamaha cart same as and need to go over the motor I’ve pulled it all down and had it sand blasted and painted now to put it back together with a few twist I’m going to pimp it a little 😂
@michaelsaville748514 күн бұрын
Best thing I ever did was change to Lithium, no more lead acid battery issues, not cheap but well worth it.
@michaeldill1567Ай бұрын
Excellent video, exactly what i needed to see 👍
@keithturpin898Ай бұрын
Please help! 2001 g19e Yamaha 48v kart stopped running. Charged the batteries and it ran for about 15 minutes, cart stopped now it does not charge or turn on. I've tested just about everything without success. 😖Any suggestions?
@fixityourself11119 күн бұрын
If the batteries wont charge id be checking their voltage first .
@yhelbeltran7552Ай бұрын
good day sir, what is the problem if the solenoid continously clicking when switch on or off?
@fixityourself111Ай бұрын
Arcing / continuity of the brushes inside the electric motor . Remove motor , clean / sand armature , replace brushes if needed 👍🍺
@yhelbeltran7552Ай бұрын
@@fixityourself111 thank you for info sir, god bless
@roflman2 ай бұрын
I know from experience VB to VH commodores are more or less exactly the same, not sure about later models
@BrianDugan-b1c2 ай бұрын
Is it possible for oil to get into the motor brushes on an electric golf cart? A mechanic is refurbishing my cart and told me the brushings were covered with oil. I don't know how that is possible.
@fixityourself1112 ай бұрын
No there is no oil that can get in there .
@karltogger-qs8xh3 ай бұрын
You knocked it out of the park. My president will abruptly stop after about 20 minutes. Do you think my brushes are bad or dirty?
@fixityourself1112 ай бұрын
Yes , very common problem
@helenburling60453 ай бұрын
great vidio , but i mistakenly turned the key past the acc and now the steering lock won/t release
@fixityourself1112 ай бұрын
Sorry slow reply , how did you go getting it to turn back to acc?
@helenburling60452 ай бұрын
Still looking. Am trying wb honeypot. Other than that I’ll put a hq barrel in
@helenburling60452 ай бұрын
@@fixityourself111 still waiting on parts from WA, the honey pot i have is HQ the new one hopefully is the right one to take the HZ key barrel i already have
@midwestcold4 ай бұрын
Like your videos. But this one is a duplicate of a previous video. I'm trying to do the diagnostic checks on electrical components on 2011 YDRE and was looking for a walk-thru. The title of this video sounded like it could help but apparently the video is elsewhere? Thanks.
@fixityourself1114 ай бұрын
So what is the actual problem your chasing?
@midwestcold4 ай бұрын
@@fixityourself111 Car will not operate in either direction - solenoid does click. Cart was purchased used 4 years ago for 4k. Put in new lithium batteries two years ago.
@midwestcold4 ай бұрын
removed the motor. Had fluid leak out as it came apart. And the smell, acrid maybe?, but rather unpleasant.
@michaelsaville74855 ай бұрын
Thanks Mick, useful test, now I need to find an immovable object, club house wall maybe………😂
@fixityourself1115 ай бұрын
@@michaelsaville7485 👍🍺
@WrenlyMari5 ай бұрын
Sir is it safe to wash the batteries with water, doesn't it cause a short circuit? Thank you for your tutorials...
@fixityourself1115 ай бұрын
@@WrenlyMari absolutely safe .
@farhozz6 ай бұрын
I have a zapi controller from pallet mover, can it be used on a brushed permanent magnet motor,sir ?
@fixityourself1116 ай бұрын
Im sorry mate but im not sure on that
@TaylorTaylor-yi4qd6 ай бұрын
Just rebuilt one on my daughter’s G29. Got to take it back out. I think the armature is bad. The cart isn’t moving at all. The A1 wire is getting hot when pedal is pressed down.
@fixityourself1116 ай бұрын
Pull that motor and check / sand the armature🍺🍺👍
@TaylorTaylor-yi4qd6 ай бұрын
@@fixityourself111 I sanded it when I had it apart but it is in really bad shape.
@fixityourself1116 ай бұрын
Ah ok If the ribs are almost gone then it may need replacing mate.
@TaylorTaylor-yi4qd6 ай бұрын
@@fixityourself111 I’m going to look into an upgraded motor for it. Thank you for the videos and help. Cheers from middle Georgia in USA. 🍻
@rtryon246 ай бұрын
Do you have a link to the input shaft bumper so I can make sure I get the correct part?
@fixityourself1116 ай бұрын
I dont have a click link mate but this is the part number for yamaha Jh7-H1829-00 Youll find that most carts us the same bumper .