fixfinito

Пікірлер

@stefanoterreni5863 7 күн бұрын

Buongiorno,ma l acqua esce perche c e una pompa che se la tira?oppure esce per caduta?

@fixfinito 2 күн бұрын

l'acqua esce attraverso lo spruzzatore, che è costituito da un ugello e da un tubo di gomma che tende ad intasarsi, poi la parte in spugna con lo straccio ruota e distribuisce il liquido detergente sul pavimento e sui pannelli

@stefanoterreni5863 2 күн бұрын

@@fixfinito ma cosa impedisce al flusso di acqua nel tubicino di uscire anche a macchina ferma?

@pietras321 2 күн бұрын

@@stefanoterreni5863ugello guarda 0,23 secondi del video

@ramonaneamtu6620 3 ай бұрын

thanks a lot! 😀

@fixfinito Ай бұрын

Np :)

@michalguziak5059 6 ай бұрын

Panowie, po pierwsze odłączanie baterie, to podstawa!!!!

@toronto7550 2 ай бұрын

A znasz się na tym modelu? Mam do wymiany płytę główną i zastanawiam się w jakiej kolejności podłączyć wszystko, a jest tu problem bo bateri nie da się na końcu bo jest zakryte wejście

@Taurmin 6 ай бұрын

What was the point of removing the 2 screws and removing the cover above the dirty water tank? It doesnt seem like you ever need it for access and the "top 2 screws" you replace later in the video are not the same as the ones you removed earlier. It actually seems like removing any screws at all is unnecessary as the only things in the way of you getting to the hose are the two plastic covers that you pry loose...

@fixfinito 4 ай бұрын

Ye ouu yee

@MyloFlappie 6 ай бұрын

Ik heb ook de FC5 witte Karcher, maar geeft geen water meer door. Alles na gekeken, terug geplaatst, lekt hij water. Weer uit elkaar gehaald, terug gezet. Gebeurd niks, geen druppel water komt eruit. Slangetje misschien de oorzaak?

@fixfinito 4 ай бұрын

@5kopiyok 8 ай бұрын

No battery?

@jozsefmihaly9381 8 ай бұрын

Még egy ilyen mocsok termék, ilyen drágán....nincs is tán!!!

@fixfinito 4 ай бұрын

@ivaylokosev8230 9 ай бұрын

Great explanation! Thank you mate!

@fixfinito 8 ай бұрын

Np ;)

@lahoof 10 ай бұрын

I can't find what's shown at 10 second in anywhere on my FC5. Can anyone help me out.?

@fixfinito 8 ай бұрын

You need take out cover there

@lahoof 7 ай бұрын

@@fixfinito Which cover.?

@Taurmin 6 ай бұрын

@@lahoof Whats shown at 0:10 is the top of the cleaning head. The quick release cover has been removed, and so has the grey button that you depress to remove it. If you are only trying to clean out the water hose, forget about any instructions to remove screws it is completely unescesarry. What you need to do is: remove the top cover of the cleaning head, remove the part that sits around the release button and has the connection for the vacuum hoses on the cleaning head side ( should just pull loose with a bit of force), pry off the release button, remove the cowling just above the cleaning head as shown at 0:18. This should give you unubstructed access to the full length of the water hose and all the parts simply click back into place afterwards. No tools needed except perhaps a flathead screwdriver as a pry bar.

@lahoof 6 ай бұрын

@@Taurmin Thank you so much for taking the time to reply with so much detail. I will try again based on your suggestions and will report back.

@fridolinoberboersch9425 10 ай бұрын

The construction is a fail

@fixfinito 9 ай бұрын

Do you know somethink better in the same money?

@fridolinoberboersch9425 9 ай бұрын

@@fixfinito Yes

@MegaChickenPunch 7 ай бұрын

Then give us the model you genius....... @@fridolinoberboersch9425

@minetuncer6830 10 ай бұрын

This is not for an ordinary housewife. The machine is very heavy to use already and things like fixing hoses, failures, uh no not for me.

@fixfinito 9 ай бұрын

Thats true

@MrNehygienix 10 ай бұрын

Thank you. In my case, it was clogged nozzle on that water hose. A needle helped.

@fixfinito 10 ай бұрын

Nice too hear it :)

@pietras321 9 ай бұрын

No problem

@kennethdoyle469 11 ай бұрын

Promo`SM

@maxflight777 11 ай бұрын

Shit video .. fucking hard to follow

@gaspardsaintolive325 11 ай бұрын

What type of screwdriver did you use? I dont seem to have the right size.

@fixfinito 10 ай бұрын

Just normal cross, im not shure what size was it

@magnus6785 11 ай бұрын

It works, but for how long. Might want to add soldering where it is needed

@fixfinito 11 ай бұрын

You are right, a more professional solution would be to find cold solder joints and solder them again, but not everyone knows how to reball BGA or diagnose damaged graphics cards, this is a GTX Titan 6GB graphics card, it is currently worth USD 50, repair at the service center would cost more than the card it is worth it and it would not be worth it, and by throwing it in the oven for 10 minutes at 180 degrees, we may extend its life by a few days, weeks or maybe even months or years, it is important to remove all possible plastic and metal parts from the card, set it straight so that the electronic parts do not move during baking - some will succeed, others will not, there is no guarantee that it will work, my Gtx Titan works until now :D

@petermeadfoot 11 ай бұрын

Thank you very much, I can now clean my floors again without having to pay for expensive repairs.

@fixfinito 11 ай бұрын

No Problem :)

@kakashi1150 Жыл бұрын

very helpful, thanks for helping out!

@fixfinito 11 ай бұрын

np :)

@jamesg8246 Жыл бұрын

356F in Freedom units

@patrycjastecyk7329 Жыл бұрын

Good idea

@Clevergirl-00 Жыл бұрын

I feel like there are missing diassembly steps.

@Laci017 Жыл бұрын

You just helped to fix my machinery :)

@fixfinito Жыл бұрын

Nice to hear it :P

@bitcoinik9171 Жыл бұрын

great :)

@MrKrusas Жыл бұрын

So useless disassemble video. Without big picture ant to fast

@mareksadkowski4739 2 жыл бұрын

Incredibly helpful guide 👍

@m4ni3x 2 жыл бұрын

Thx 4 help. nice job :)

@monikaaszewicz7855 2 жыл бұрын

Great video! 💪

@patrycjastecyk7329 2 жыл бұрын

Thank you! Now problem solved! 🎉

@pietras321 2 жыл бұрын

Me too

@mareksadkowski4739 2 жыл бұрын

Really helpful guide, thanks!

@WieszJakJest321 2 жыл бұрын

Nice

@pietras321 2 жыл бұрын

Great Job, Thanks

@M3TICO 2 жыл бұрын

jak nie zmieniać baterii 👍

@xxxxxxx359 3 жыл бұрын

👍👍👍👍👍

@emperormarcusaureliusanton5995 4 жыл бұрын

Thanks for the video, very informative! Does this laptop motherboard have an LED slot for backlit keyboard?

@fixfinito 3 жыл бұрын

i dont think soo :)

@mymitik 4 жыл бұрын

A co z norma ip67? Zostaje zachowana?

@mixer6971 4 жыл бұрын

Nie XDDD

@fixfinito 3 жыл бұрын

Jest lipa :(

@m4ni3x 4 жыл бұрын

Very useful video, thanks bro :)

@fixfinito 4 жыл бұрын

Thanks mate

@paplakovpaplakovski8727 4 жыл бұрын

Very Nice. Thank you its safe my life.

@fixfinito 4 жыл бұрын

Yo Bro

@kr00l90 4 жыл бұрын

Ile fps będzie w csie?

@fixfinito 4 жыл бұрын

około 5-6

@ResolvedAim 4 жыл бұрын

4k 4:3

@ktosjakis007 4 жыл бұрын

Nawet fajny secik ale karta graficzna do wymiany ;/ w tej cenie są lepsze ale nie pisze że to najgorsza możliwość ale na twoim miejscu trochę bym się bardziej zagłębił z ekonomią podzespołów

@ADV_PO 4 жыл бұрын

Tłustymi paluchami dotykasz podstawy coolera i nakładasz pastę. Odtłuszczaj IPA40. Procesor wrzuciłeś w socket - miałeś szansę pogiąć piny. Rób to wsadzając najpierw jeden róg w socket potem drugi i potem delikatnie kładź CPU. Procesor na który nakładałeś pastę nie wyglądał na odtłuszczony. j.w. A przede wszystkim nie nakładaj też tyle pasty. Za 2 lata możesz mieć problem - wyjmując CPU wykruszy się z brzegów w socket. I sprawdzaj proszę jak zainstalować poprawnie pamięci w sloty. Miało być A2 i B2, a wsadziłeś A1 i B1. Przy grach na średnim poziomie - może nie będzie BSOD. Ale przy wideo lub renderowaniu - pełna szansa na błędy.

@fixfinito 4 жыл бұрын

Dziekuję za porady ;)

@ADV_PO 4 жыл бұрын

@@fixfinito Proszę Cię bardzo ;)

@mareksadkowski4739 4 жыл бұрын

Niezłe cacko. Ciekawy filmik. Propsik 👍🏻

@fixfinito 4 жыл бұрын

Dziękuje

Ең жақсы KZbin

Пікірлер