Yes, Diablo makes a 12 inch aluminum blade for a chop saw, I cut aluminum all day long, even 1/2 inch thick plates

I've had my heat pump water heater for 5 years now. And I didn't know that I shouldn't have it on the energy saver for maximum savings.

Like u are not sure

Thanks for this. I have that pulley but the issue I am having is when the line is slack it keeps getting jammed between the pulley and the bracket beside it.

My GX 345 is making a clunking noise, I bet that is what it is.

great great job

For over a year, driving at highway speed for any length of time, my 2018 Acadia has been tripping the P0128 code, with all the symptoms you mentioned. I've been clearing the code with a scan tool, and it has continued to happen. The last time, however, I continued to drive and the problem resolved on its own....fan stopped, temp gauge returned, A/C worked. Now I don't know if I want to pull the intake off and try to replace the sensor and thermostat. Possible computer error? I don't trust my local shop doing this job.

Going to try it tomorrow............

good video. wish you were in Florida

I have a question. Did you have any problem with the starter generator charging your battery the way you wired it ? Did everything seem to work good over time ? Thanks...

THANK YOU THANK YOU THANK YOU, YOU'RE FAR TOO KIND

@18:48 I planned to adjust the drum brake 1st (via access window) and then remove the drum and apply Copper Anti seize on the Hub. It seemed normal drug (very similar to shown @19:20, hard almost impossible to rotate), but when I tried to remove the drum, it was impossible! Through the adjusting window (on Nissan Sentra it is on the front), I succeeded to contract that Adjuster a bit (and it was very hard), so I removed the drum w/ a lot of difficulties, prying w/flat. So my question is, when you adjust the drum via that access window (hole), should it be still option to remove it? Or you can leave like that a bit too tight hoping that it will self adjust on braking? This car is 2009 Nissan Sentra (w/access window (hole) on the front). We have another car 2001 Saturn SL2 without any access to the Star Adjuster, so on that car you obviously need to have an option to remove the drum. But I think it might be different on different cars. I would appreciate any opinion on this confusing question. Thank you for your educational film.

I need to do my daughters Sentra and found this. I appreciate you sir 🫡

What about giving a try with antifreeze as an extra balancing method.

Ahhhh! All the damn bird chirping in the background. You must get up early.

Suggestion: prior to the actual removal of the intake manifold, use an air gun & blow all the debris away from the area so it can’t fall into the engine.

Thanks for the information

Too much babble

Love your old school ways, especially your torque method. Thank you

This was my problem, Thanks. I found the key under my tractor.

Nice video! I'm going to go ahead and tell you what happened to mine but it is probably a gonner. I was having trouble with the blades not engaging. So I pulled the deck and replaced the clutch cable. Mowed a little but it started smoking, burning a belt. I repeated the same process with removing the deck. Everything checked out fine. Mowed a little again, same issue. Same procedure with the deck. I discovered a pully seizing up. I fixed fixed that. Mowed a little. Blades engaged but engine would stall. Then the engine started to run really rough and at a very high idle. You'd think it was souped up for mower racing! This whole time I needed a battery and would have to jump start it everytime. I parked it for a few days until I could afford a battery. In the meantime I replaced the fuel and air filter. When I got the battery, the engine fired up immediately. But the idle was still very high. As I let it warm up to lower the throttle lever there was a sudden BOOM with a cloud of smoke. The engine was still running but I quickly turned it off. Upon inspection I could see a huge gash in the engine case right in front of the battery between the #1 and # 2 bolts you referred to in this video when you were dismantling the motor. Whatcha think? Is the case even worth trying to replace, let alone whatever the Hell let loose to cause the calamity? I live in Texas, north of Houston and will kindly give this mower to you or anyone you know of that can come get it for trade for a decent push mower. The rest of the mower is in decent shape, just not as clean as the one you worked on. I just want to mow my yard, Man! It's been 2 years since I was able to.

I had problem with john deere 2006 X300 42 inch mulcher. I bought mine X324 2008 48 deck 16 years old just change a belt last year at 745 hours also do snow blowing. Solid like a rock.lol. but my son X300 mulcher deck you can`t find after market belt for them please go buy A original belt @John Deere part# M153160 size 5/8 X 156.6 inches ,you`ll save yourself a lot of trouble with 7 pulleys & 8 belt guide with very litle space between them After market belt will all shread apart fast or slow but wont last a year. lol.Change all pulleys 2 spindals, & stop at 3 belts bought OEM problem solve . But my X324 48 inch deck you can use after market belt no problem. look for M154958 5/8 X 111inches. I Like your video good job man . I like finding modification like that .

with that being an exhaust pipe that gets hot.. there’s no way you can protect it from further rust.. how do you stop that pipe from getting pin hole leaks in the future.. i’m not talking about flanges but the actual pipe 😮

That's what i figured is wrong with mine a valve adjustment but does that mean it's too tight or loose or could it be either or an have to check it with a feeler gauge

Super helpful thanks

I’d put 2 quarts of trans oil in my 4.0 and ran it for 10 min to clean out gunk worked pretty well

Did you ever get it fixed ? I think the reason most trucks come with wimpy looking street tires is to keep from shaking and riding like crap.

I have the same fridge and I have a problem with the defrost heater. I would like to know where I can find the technical specifications sheet or if you can provide me with a copy. Thank you.

Que torque yeba los balancines

Thank you for the attention to detail at 11:47. How you demonstrated the importance of maintaining the stairstep at around 5 1/2 to 6 inches (to the left of every shingle )I’ve seen many Roofing videos and you’re the first one to demonstrate this concern to great detail thank you very much.!

13:50 Maytag side by side refrigerators. The ice maker does not make ice and stopped dispensing water

Pull air from the attic during the summer and vent the cold inside. During the winter switch to intake from the inside and vent to the outside. During the summer it is running as a hybrid solar system. If you vent the exhaust into the house during the winter, your furnace then has to make up the difference working it harder as the heat is coming from the air the furnace previously heated and then has to be reheated.

Why do you have the cable attached to the top of the plow? Thats the worse thing you can do for the life of your cable.

Everything Ive read says to face the buttons towards the rear of the car. Is this true? It looked like yours was facing the front.

New impeller is $300 new blower assembly is $1600

Well John you just convinced me to buy the Orbit. Actually the XL Model. What part of Ma are you in?

You Da Man... Been cursin this treadmill for cupla years was ready to ditch it......BUT you saved it...Worked on my Reebok crossover Thank You ...Thank You

Hub centric rings the wheel isn’t centered with out them if you still have them try rings and drive that truck more not good for the engine to sit

First of all, stop moving the camera around and focus more on what you are doing with your hands, and fck off the music that we can't hear you over. Sht video.

I was able to use a Stanley 5/8" (Cr-V 88-980) with wobble extension. Everything else exactly like in the video. Issue persisted for roughly 50 miles after replacement then corrected. Has ran fine for 4 months now.

Hi, I'm trying to program my 2019 Acadia Denali. Once it says to put the key fob in the tray, I did, and then nothing comes up to say insert key 2. Now, the whole vehicle is shut down. Help, please.

Nice fix. My UTV's winch came with steel cable. That cable (and the fairlead) were the first things I replaced. If you haven't done so already, think about replacing that steel cable for synthetic rope. It's safer and easier to handle. Looks like a KFI plow. If so, they make a bracket that mounts on the push tube near the blade which raises the cable mounting point. Still lifts the plow more than 2 feet off the ground (if you need it to go that high) but takes most (if not all) the weight off that roller fairlead. If it's another brand, then it should be easy enough to make a bracket to raise the cable attach point. My setup currently has rope with a Hawse style fairlead and the bracket mentioned earlier. I just got a winch strap that I'm going to swap in to save my winch rope from getting all bound up on the winch roller due to all the winding & unwinding. The strap is much shorter in overall length so binding isn't an issue.

Thank you fix my problem sweet

I had the same problem and it was the fuel lines. After changing the fuel filter it compressed the inside plastic liner in the fuel line causing reduced fuel flow. Would starve for fuel after a couple minutes.

Can anybody make a video without cursing?

That’s weird

This helps so much! Thank you! Any chance you can link the parts from Amazon you bought? I have to replace this on my car! 🙏

Thank you this helped a lot. The black stuff on my pads was very minor but enough to cause me to have to press harder than normal

Dumbest way to do this. Jack up the bed. Eight bolts on the bed-- three screws on the filler neck- two jacks. Takes about an hour and you haven't destroyed the bed of your truck. Idiot!

Good job I have a same problem with my 2011 Colorado and I will do same like you did thank you show and explain 👍 👍