Zul_Fix

Пікірлер

@matheus.k7552 3 күн бұрын

mine was acting weird like that, changed the power board and the flex cables, solved

@kingofenglandthethir 10 күн бұрын

Some moto g31s are a little different than this one in the video. Mine doesn’t have a fingerprint sensor on the back. My fingerprint sensor is on the right side and acts as the power button. I have learnt a lot here. This the best replacement screen on the moto g31 I have seen. Thank you.

@zul_fix 7 күн бұрын

It was the only one i came across. And thanks for your comment it is these kinds of comments that make me continue doing videos. Thank you

@Stand-as-One_Virox 15 күн бұрын

Hi, I appreciate your video and the valuable information, but I have a question. My battery says 2.84V. Does this mean it's bad? The phone was not charged for a long time with a broken screen and now I replaced it with a new one (new screen), but it's stuck in this boot loop. Could that be the problem or is that 2.84V normal? I ask this to buy a new battery. Thanks for answering and I subscribe.

@zul_fix 10 күн бұрын

Hey there, fully charged should be around 4,4v. If it was left a long time without use probably needs a jump start but in order to do that you will need specific hardware to connect it. So it most likely is no longer receiving a charge so might as well to just buy a new battery.

@edmardivinodesouza9967 16 күн бұрын

Bom dia, quais as dimensões do Thermal que você usou? Obrigado!

@zul_fix 16 күн бұрын

Boa noite, este era o 32x32x0,2mm

@Bekahcavalcante 29 күн бұрын

Obrigado

@zul_fix 26 күн бұрын

De nada, obrigado eu!

@landonhamilton2016 Ай бұрын

Call the same way and get out the house because you can download any new Albany or team info from I don't want it was actually the only time

@zul_fix Ай бұрын

Hi im not sure that if that comment has something to do with the video?

@mark.893 Ай бұрын

How did you remove the zip tie?

@zul_fix Ай бұрын

Used a sharp tip knife and bent the inside of the zip tie so it could free it, but you can just cut it and put a new one in place.

@LiamWhit Ай бұрын

My ps3 slim only turns off after gameplay like gta iv. The 3 beep red flashing. Syscon code has to the 1002 error

@zul_fix Ай бұрын

It refers to the NEC Tokins so might as well replace them or just add the caps like i did on this video.

@LiamWhit Ай бұрын

I'll do that, when I add them should I add it to the exact place where u put yours? What exact resistors did you use. I have thermal pads and paste sitting around so I'll do this

@zul_fix Ай бұрын

@@LiamWhit You can place them anywhere around the Original NEC Tokins as long as you have the negative side of the caps on the negative side of the board and the positive side of the cap on the positive side of the board. Where the Negative is the inside where the tokins are and the positive the otherside of the line. 470uf tatalum capacitors are what i use.

@LiamWhit Ай бұрын

@@zul_fix thanks seems straight forward! Where u put yours just the 2 with thermal pads ontop do u reckon that will do the trick? Is it just giving the capacitors extra strength in simple terms. Had to add in. Instead of using grinding tool would a small flathead screwdriver be okay to use, have seen others do that

@zul_fix Ай бұрын

@@LiamWhit Hi again, yes tthe thermal pads adds extra strenght cools them down and also avoids continuity in case the solder toches the plate which shouldnt do. If you dont have a grinding tool you can scrape it with something sharp, make sure you dont go too deep though.

@SlarkandFriends Ай бұрын

Low battery?

@zul_fix Ай бұрын

Broken wires inside mate.

@thumper5555 Ай бұрын

I don't know what it is about this video, but I watched all of it for pure entertainment. I do need to clean my Sixaxis controller, but I just sat back and watched this video. I'll watch it again when I actually get around to cleaning my Sixaxis. Great stuff, my friend.

@zul_fix Ай бұрын

That is really nice to read, cant thank you enough for the feedback as that is the purpose of why im doing the videos in first place. Many thanks!!

@AndreFerreira-nc3sn 2 ай бұрын

Where did you buy the replacement wheel?

@zul_fix 2 ай бұрын

Hello bought on aliexpress just search for the vacuum model it will come up with loads of spares.

@dimepia123 2 ай бұрын

hahaha a fkin piece of glitter

@zul_fix 2 ай бұрын

ehehe who would've known, don let your kids next to your devices!!

@xpaydaymoney8552 2 ай бұрын

Can someone please I'm struggling with no red light issue as well but my console isn't turning on anymore wat should I do

@zul_fix 2 ай бұрын

Hello maybe this is a power suply issue? Have you tried a good working one?

@Adam_editcr7 2 ай бұрын

How can i fix connect the dualshock 4 using the usb cable ps4 but my usb cable is broken like yours in the video

@zul_fix 2 ай бұрын

Not sure that i understood your question, but if it has the same problem as this you need to replace the chip on the console, if that does not fix it you have a problem on the south bridge.

@ccccklmrun8868 2 ай бұрын

on the ps3 controller did you try to change the foam piece behind the flat cable? Mine was pressing random buttons too because the foam piece got squished making the contact with the motheboard fail (i just added some tape to help it get better contact)

@zul_fix 2 ай бұрын

I have not, to be honest i just thought it was a failing flex. Will give that a try maybe using a bit of IPA since these foams usually expand with it. Thanks for the tip!

@fi7959 2 ай бұрын

They released a revision to the Pro that changed the fan profile, the entire time I had my Pro it was never that loud.

@zul_fix 2 ай бұрын

Yes i believe they reprogrammed it to let it go hotter before the fan kicks in.

@TyroKith 2 ай бұрын

The last model, CUH-7215 I believe.

@雷蔡-o7t 2 ай бұрын

沙雕

@zul_fix 2 ай бұрын

@florin1980 2 ай бұрын

Thermal pads are on coils and not on mosfets. Try again.

@zul_fix 2 ай бұрын

Nice spot man i have placed them on the wrong place, thanks for pointing that out, we all make mistakes. It not noisy anymore at least!!

@serghv4766 2 ай бұрын

Try using Honeywell ptm7950

@zul_fix 2 ай бұрын

Will try to find where to buy that. Tks for the tip.

@jazero-u7p 2 ай бұрын

At least you were brave enough to give it go albeit a fail. We learned by our mistakes. NSC YT has made a good tool for it. My home made one works very well and made like NSC concept with art painting knife but I bent the tip of the blade and the process of bending the tip is by gas burner and then bend and cool. Then hand sharpen with a traditional knife sharpener. Cheap and effective. Cut Rsx like butter I heat lid of cell for about 400c to 500c 40 to 60 seconds and then cut.

@zul_fix 2 ай бұрын

I already thought of buying the NSC one, has i dont have a gas burner at home otherwise would give your tip a go.

@jazero-u7p 2 ай бұрын

@@zul_fix The NSC one is effective but I do not know the cost. You can try to make it, use gas stove or small plumbers torch gas blower to heat the metal let it cooled a little bit and then bend 10cm size with pliers in L shape as its is easy that way and dip in water to cool and repeat until right angle is achieved in L shape . Then file or sharpen.

@takuminightcore1886 2 ай бұрын

Yeah, this is 100% on Sony‘s end. I’ve just not given it a good quality of thermal paste that needs to run high demanding games efficiently especially this was made for 4K TV audiences. I did that with my PS4 Pro and I’ve noticed a complete difference after just re-pasting it. I didn’t even have to replace the thermal pads. It ran completely stable without any issues.

@zul_fix 2 ай бұрын

Ya thats a major defect on the apu ive read that its not properly straight on top thats why it spreads the paste out to the sides.

@Vreze 2 ай бұрын

What size is that screwdriver? My mom has the same boot loop problem.

@zul_fix 2 ай бұрын

Hi it is a philips 00

@Vreze 2 ай бұрын

@@zul_fix thank you.

@grantcleveland1 2 ай бұрын

What is that glue you used to seal the back cover?

@zul_fix 2 ай бұрын

Used double sided 3M and B-7000 liquid glue.

@elprofessor99 2 ай бұрын

hard work but a good result keep posting thank you for sharing

@zul_fix 2 ай бұрын

Will do thanks for watching!!

@rrouter2 2 ай бұрын

First program MCU pic 😂 😂

@zul_fix 2 ай бұрын

Ah it needs programing? Didn't know that xD

@RmFrZQ 2 ай бұрын

It's really difficult to repair these days. Not only you need to have steady arms, good eyes and at least semi-professional grade equipment. You also have to get a good parts, because the ones you order from AliExpress often comes from a faulty batch, or even completely fake relabeled chips altogether. And everything is programmable these days, from PWM controllers and multi-controllers to microcontrollers and you have to somehow get the firmware from original burned ICs and program the new chip.

@zul_fix 2 ай бұрын

I wondered if it was another chip that was broken, could be just a reprogramming instead then. I ended up just buying a faulty vaccum same model and switched the boards so that my friend got his vacuum back working :D

@salalkhairaat8156 2 ай бұрын

do you programing that pic32 mcu?

@zul_fix 2 ай бұрын

I have not, was not aware that it needed to be programmed, need to search on how to do that though.

@Moxzot 2 ай бұрын

A screwdriver and you had the soldering iron the whole time, jesus what is wrong with you. Oh and you had hot air too, why didn't you use that rather than pry at it like a neanderthal.

@Moxzot 2 ай бұрын

You dont have to spread thermal paste out please stop doing that its not a cake.

@zul_fix 2 ай бұрын

I have seen multiple opinions and videos on that, and spreading with a little blob on the middle was what worked best on their case. Feel free to let me know how you usually do it please!

@Tetra418 2 ай бұрын

Did removing the mother board erase the data from the phone?

@zul_fix 2 ай бұрын

Not at all, just resets the date and time, everything else stays there.

@theoneandonlykctcb6366 3 ай бұрын

Cheers buddy, great breakdown.

@zul_fix 2 ай бұрын

Thanks for watching cheers!!

@edgarescobar5935 3 ай бұрын

Yo logre repara 1 con las laminas anti drift que venden en Aliexpress aun que no quedan tan perfecto al soldar, el control logro funcionar a la perfección sin drift

@zul_fix 3 ай бұрын

Puedes linkearlo?

@Aman--Wangnao77 3 ай бұрын

My ps3 slim shuts during god of war 3 and givss blinking lights. Gta 5 runs fine for hours. My syscon error log has a lot of A0801002. Can i fix it by following the process you did ? Also, its been over a year, is your console working fine ?

@zul_fix 3 ай бұрын

Yes 1002 refers to the nec tokins closer to the rsx so try this procedure it should start right up, if you want something for longer term replace the 2 nec tokins at least. And yes this ps3 still up and running.

@Aman--Wangnao77 3 ай бұрын

@@zul_fix Thank you so much for the response. Just one more question, I found some 470uf 16v caps on Amazon. Would that work ? I could find the 6.3v caps

@zul_fix 3 ай бұрын

@Aman--Wangnao77 should be good the voltage limit does not really matter as long as it is not under 6.3v.

@Aman--Wangnao77 3 ай бұрын

@@zul_fix the ones I found has a high ESR rating. Can I still use them ?

@wilfredynunez5263 4 ай бұрын

Thank you so much. I was having trouble finding a video that shows how to fix a Sixxaxis and not a Dualshock 3.

@zul_fix 4 ай бұрын

Thank you for watching and glad it helped you!!

@Super_Bros. 4 ай бұрын

Not a bad repair; I have also fixed one on these.

@zul_fix 4 ай бұрын

Very nostalgic, I remember the xmas when i first opened it.

@MrRabbitXP 4 ай бұрын

ele parou de ligar e desligar sozinho?

@zul_fix 4 ай бұрын

Sim depois de tirar a purpurina ficou boa.

@MrRabbitXP 4 ай бұрын

@@zul_fix opa,obrigado pelo video,o meu estava assim também,abrir ele e limpei a chave de liga e desliga,é agora esta 100% 😀

@zul_fix 4 ай бұрын

@@MrRabbitXPahaha que bom que deu para ajudar! Obrigado

@Abewas-channel 5 ай бұрын

Nice video new subscriber

@zul_fix 5 ай бұрын

Many thanks for watching and subscribing!!

@Chezgatt2000 5 ай бұрын

Obrigado por esse vídeo, saudações do Brasil!

@zul_fix 5 ай бұрын

Obrigado eu por ver, também fiz versão PT do mesmo video! Saudações

@gottosahani7571 5 ай бұрын

Thanks ❤

@zul_fix 5 ай бұрын

You are Welcome!!

@xpaydaymoney8552 7 күн бұрын

Does apply towards cech 2001a I'm experiencing the same issue as well

@helby255 5 ай бұрын

Hey, guys. I have the same problem after replacing the lcd. The solve is just a plug other charger. My charger just broken when I repair my phone...

@zul_fix 5 ай бұрын

Thanks for the tip!

@xS7EzRAGEx 5 ай бұрын

Lead free solder 🤦‍♂

@HAMOUDASCRAFTS 5 ай бұрын

I need to know the name of those capacitors their numbers and their full name so i know exactly what to buy

@zul_fix 5 ай бұрын

Hey You have a link on the description that takes you to the store, search for 470uf tantalum capacitor.

@HAMOUDASCRAFTS 5 ай бұрын

@@zul_fix okay thanks But are these capacitors works with all ps3 models if not can you tell me their name too Thanks

@zul_fix 5 ай бұрын

@@HAMOUDASCRAFTS no it only works on the fat models and this slim version that has the nec tokins, the 2000 series if i am not wrong.

@HAMOUDASCRAFTS 5 ай бұрын

@@zul_fix thanks

@Thatonedude547 5 ай бұрын

My ps3 works and i can play games but in intensive games such as red dead i have ylod does this mean i only have to add 2 capacitors like you did?

@zul_fix 5 ай бұрын

Hey It either needs a good clean or it has a dieing rsx. In your case adding caps will not help.

@Thatonedude547 5 ай бұрын

@zul_fix I've cleaned it and change thermal paste and still have this problem

@Thatonedude547 5 ай бұрын

@zul_fix I have a ps3 slim too not fat

@zul_fix 5 ай бұрын

@@Thatonedude547 What model is it because there are some early revision that still have the same problem as the fat. Did you replace the thermal pads on the ram as well?

@Thatonedude547 5 ай бұрын

@zul_fix it's model 2004A something like that, no I didn't change ram pads

@michaelolayinka441 5 ай бұрын

I knew there should be a way to just increase capacitance by adding to the originals 👍🏽

@zul_fix 5 ай бұрын

Easier than scrapping everything 😄

@knightwar3 5 ай бұрын

At 4:20 the inductor marked L6 is burnt out which means very high current went through it probably the transformer is also shorted and now the emi filter inductor is gone too, LearnElectronicsRepair has some good videos about power supplies if you wanna check it out

@badrinathgunaseelan317 6 ай бұрын

Bro I'm having acer predator helios Neo 16 4050 variant , Its overhaeting i.e cpu hits 99 degrees while gaming how to fix this

@badrinathgunaseelan317 6 ай бұрын

I even replaced the fans

@zul_fix 6 ай бұрын

Did you replace the thermal pads and the paste?

@badrinathgunaseelan317 6 ай бұрын

@@zul_fix no bro I only bought before 9 months ago , customer guy said yours is liquid metal thermal paste and you don't need to apply it for atleast 2 years . My problem in short is cpu cores #5 #7 are producing more heat

@zul_fix 6 ай бұрын

@@badrinathgunaseelan317 maybe he has not applied it well and it has dry spots. If you are ok doing that purchase liquid metal and check if the cpu is fully covered by liquid metal. If its not then use the bud that comes with the liquid metal to clean and the seringe to reaply it.

@crescentsheath1190 6 ай бұрын

Hello. I noticed when you was trying to find some shorts, it didn't beep when you tested the 2 color capacitors. I was wondering if you know what component it is, and if you are measuring with resistens which number are you giving. :) 1:05

@zul_fix 6 ай бұрын

Hello. If you mean the white ones with the little dot on them they are resistors. Unfortunately this video was a while ago so i do not remember the values, im sorry.

@MichaelDaponte-fy9ji 6 ай бұрын

Were did you get the parts to fix it

@zul_fix 6 ай бұрын

Hey, I have linked everything on the description, hope it helps. Thanks

@lautarocorreabarrios9053 6 ай бұрын

Is possible to put a 3pin analog on 4pin controller? (I nephew screw my left thumb, and in my country is impossible to get the 4pin analogs, and shipping from other counrties will cost maybe 2 times a second hand controller)

@zul_fix 6 ай бұрын

Not that i know of, have you tried the link i have on the description? It comes from china though.

@LeetPanda 4 ай бұрын

You can replace only analog mechanism, while keeping stock 4pin hall sensor housing. Ofc if problem in hall sensors or magnets - it's over. This mod may require some efford, cuz mounting pole on potentiometer-based analog module not the same as hall-based ds3 pole, it's a bit smaller and doesn't have locking clip, so you need glue it or something. Idk why no one ever tried to mod 3-pin stick and ppl still buying 10-15-years old used analogs, which feel awful

@zul_fix 4 ай бұрын

These i bought are old but feel normal to use.

@LeetPanda 4 ай бұрын

@@zul_fix they r good, may be more durable than newer models in term of stick construction, having 2 centring springs inside, but after 15 years of use ofc they can't be that smooth as new, even after lubbing. i use few drops of krytox 105g0, move stick a bit to lube spring and bottom part, than 205g1 for upper moving parts

@zul_fix 4 ай бұрын

@@LeetPandatruly are at least they will not drift over use. Will see if we have that lub were i live and give it a shot. thanks!

@LevitiqueWase 7 ай бұрын

I had the same problem after trying to root my Samsung s10 tell me what to do 😢

@zul_fix 7 ай бұрын

try to do a reinstall on the samsung system, you have tutorials on you tube that show you where you can find all the tools

@forestjuice88 2 ай бұрын

Maybe wear a rubber next time

Ең жақсы KZbin

Пікірлер