2 жыл бұрын
2 жыл бұрын
Пікірлер
@haydenrichardp3712 4 ай бұрын
Those look like used pistons.
@roycekelly4774 5 ай бұрын
When you installed the rear taillight, were you able to send rivets through the outside holes without intercepting the cooler? Usually the outside holes fit over the bolts that come on the rear bumper bracket, but noticed you didn’t install that. Thanks!
@themediocregarage 5 ай бұрын
Yes you can put all 4 rivets into the tail light. The holes line up with the edges of the cooler underneath so once you line it up you’re good to drill all 4 holes.
@roycekelly4774 5 ай бұрын
How much did you chop off? Thanks! The CR tunnel adds about an additional inch or so
@icyrc 5 ай бұрын
What temperature did you see on the trails with it on vs it off
@nxlvbel7099 6 ай бұрын
Where do I find that bumper
@themediocregarage 6 ай бұрын
That was a skinz chopped tunnel bumper.
@Shorts360dog 6 ай бұрын
Great breakdown! Unfortunately I’m needing to do this exact project. Very informative video. Thanks
@dawsonpayne1630 7 ай бұрын
Did ya weld it yourself?
@ithinkicangarage8026 7 ай бұрын
How did you like the khaos conversion?? I am thinking of doing this on a pro163
@dirtyfacegeorge9938 8 ай бұрын
That loos like aluminum from the piston in the cylinder , that can be cleaned off with acid.
@mikyg8564 8 ай бұрын
Great video bud. I have an 18 SBA 800HO and was doing a top end rebuilt. I’m familiar with engines but never done a new gen snowmobile so it was nice to watch your videos to familiarize myself with the entire engine, its component and the how-to about it. Thanks.
@nombr 9 ай бұрын
Solid video man! I came here because I want to check out my reeds, seems like they’ll be a pain to get out on the sled lol
@joelaichner3025 9 ай бұрын
That bearing sounds like my old child support payments ?
@joelaichner3025 9 ай бұрын
Most chicks don’t know it , but when you marry a snowmobiler ? We know how to build & Fix Shit ! Master of all Trades ? Snowmobiler
@joelaichner3025 9 ай бұрын
All that extra time , should have saved some time now ? Send it to SLP , get Performance Edition Stage 4 job , run with the 850’s ,
@jeffreyhagelin3672 11 ай бұрын
Wahl Brothers has a solution in the way of a bolt on adjustable mounting plate which allows the front shaft to be adjusted up or down.
@dalenylund2078 11 ай бұрын
How did it end up riding after all the work?
@WyattRauk 11 ай бұрын
Could you by chance let me know what the torque specs were. Iv been looking but couldn’t really find a good source since they were all a little different
@ryanbenbow-zx2sd Жыл бұрын
Don't look like it got any oil at all eh
@ovvazquez1 Жыл бұрын
Hi great video. Not sure if You put the engine together by now but by any chance have you check the balance on your primary clutch? I know water would be bad but there has been many sleds submerged in lakes and they run perfectly fine afterwards. I am curious if your failure is related to clutch imbalance overtime loading the bearing and starting to spall, slight lost of centerline driving pistons wear. That is a pretty hefty bearing for just water failure as the root cause. If you check the balance and still within spec… then I buy the water been the root cause. Good luck!!!
@themediocregarage Жыл бұрын
Hey thanks for the comment! Good point. I actually did check the clutch balance and it was well within spec. I’m thinking there was just enough water in the bottom end that it washed a bearing 😐
@JMX07 Жыл бұрын
how has the fix kit treated you?
@themediocregarage Жыл бұрын
I got an awesome 1200km on it and then sold it once the 9R showed up.
@JMX07 Жыл бұрын
@@themediocregarage awesome! Do you remember what brand fix kit it was?
@themediocregarage Жыл бұрын
@@JMX07 was a wiseco durability kit.
@danielleonard640 6 ай бұрын
When you gap the new rings, do you remember what you set them at?
@magistr18Ekb Жыл бұрын
Hello from Russia, thanks for the content! I always watch your video. I have a PRO RMK 800 163, I increased the cooling of the motor by installing a cooling radiator from BRP summit. instead of a plate in the middle of the tunnel. I apologize for the errors in the text, I use Google translator.
@themediocregarage Жыл бұрын
Thanks for the comment! That sounds like a great way to help with the engine cooling.
@stephrace Жыл бұрын
Hello ! great video. Can I remove the starter completely, with the big bolt and an impact, or do I have to disassemble everything as you show when you reinstall it. Do I need to remove it to open the base? I have to open the base to change the water pump shaft. Switchback Adventure 600 2012. Thank you!
@rtsousley1 Жыл бұрын
I'm also curious just how well this worked. I ordered 2 kits today for my 800 and 850, hoping they're a big help.
@themediocregarage Жыл бұрын
I definitely noticed a good improvement with cooling. It is super rugged as well and held up well which I had been concerned about.
@logansheppard3066 Жыл бұрын
Still having good luck with this cooler? My RMK 850 gets too hot I’m checking this out
@themediocregarage Жыл бұрын
Yes this definitely helps out with running noticeably cooler on the trail rides into the mountains. Also it held up well even when tree bashing. No leaks.
@Bomberboysllc Жыл бұрын
That poor sled has been molested
@tystensland204 Жыл бұрын
Damn how much for all that 8500 bucks
@justinvaughn7068 Жыл бұрын
What tunnel stiffener/bumper did you go with
@themediocregarage Жыл бұрын
I have the Skinz tunnel chop bumper on there that runs up to in front of the back running board mount.
@Neel-xe1po Жыл бұрын
You do any riding yet this year??
@themediocregarage Жыл бұрын
Headed out this weekend!
@sledderz4066 Жыл бұрын
What does drilling that hole do. I just did the khaos conversion and I’m wondering what drilling the hole to put in the skid does.
@themediocregarage Жыл бұрын
If you just do the khaos conversion you don’t need to drill that hole to lower the front of the skid. Drilling that hood is part of the setup when you put the Ice Age Elevate spindles on. The spindles are taller to give the front end of the chassis more clearance so you need to drop the front of the track in order to keep it properly engaged with the snow. If you just did the elevate spindles but didn’t lower the front of the track apparently you would have to much extra ski pressure.
@carsonstumpf9159 Жыл бұрын
How did it react with out the ice age spindles and new shocks?
@themediocregarage Жыл бұрын
Only changing out the a-arms just narrows up the ski stance and made it a bit easier to get on edge and side hill etc.
@timsiskow6850 Жыл бұрын
Find an Allen head bolt
@michaeldoerksen7551 Жыл бұрын
Did you use the stock bogey wheels in the rear?
@themediocregarage Жыл бұрын
No the Ice Age rails are cut for an 8 inch bogey wheel so the stock 7.25 inch ones won’t work. I just purchased the 8 inch ones with the rails.
@codyr4526 2 жыл бұрын
Any vid of ridding it
@themediocregarage 2 жыл бұрын
Not much no. Hoping to get set up for more riding footage this year.
@IanTorrey 2 жыл бұрын
Great series of videos. Just about to rip in to my 2015 Switchback that has 22,000 km. Your series looks like it’ll be my go to, whether I buy a short block or decide to have the crank and cylinders done separately. I haven’t had the engine out of an Axys before so this is perfect for my needs. Thanks.
@twisted__axis9435 2 жыл бұрын
Who did you get your motor from?
@themediocregarage 2 жыл бұрын
BWC powersports in Edmonton. He was great to work with.
@clintkeele1415 2 жыл бұрын
Good video, for someone that’s never pulled a motor or someone that’s pulled many. You broke it down really well. Thanks
@themediocregarage 2 жыл бұрын
Thanks!
@shagsmcshrivels 2 жыл бұрын
Is this the new rebuild?
@themediocregarage 2 жыл бұрын
No, thankfully the rebuild is running strong. Just fiddling around with old footage.
@shagsmcshrivels 2 жыл бұрын
@@themediocregarage perfect! Love the content keep it up
@ujarneqsrensen8745 2 жыл бұрын
Did you prime the oil pump before starting it up?
@themediocregarage 2 жыл бұрын
No I didn’t. Pump stayed fully primed while removed. As I installed each line I just made sure there were no bubbles in the line.
@user-ng9en7nk4d 2 жыл бұрын
Good afternoon! Great video!!! It would be nice if you could show me how to clean the ves valve. And then how to set it up? It will be very helpful for me! Thanks for making these videos, very helpful!
@sikkrides2739 2 жыл бұрын
Nice install video. So was this mod worth it? Did you notice a change in temps?
@TurboLundin 2 жыл бұрын
Definitely doing this to my sled this summer!!
@nombr 2 жыл бұрын
Good review man, what temps were you running? I have a 163 on a 155khaos chassis, am thinking of bringing her down to kelowna in the off-season just for the cooling benefits ! Haha
@themediocregarage 2 жыл бұрын
Sounds like a sweet setup you got there. Typically my sled will run about 51 - 53 degrees when the trail isn’t icy. With the cooler on there and an icy trail I was only up to 61 at the hottest and if I just kept a decent steady speed it would fluctuate around 57 - 59 while other guys sleds were up in the 80s and higher and they were having to stop and cool them off.
@shagsmcshrivels 2 жыл бұрын
Thanks
@PunisherGamingable 2 жыл бұрын
just put a new top end in my sled and when i started it the oil light and engine light came on as soon as i started it did this happen to hou
@themediocregarage 2 жыл бұрын
Thats no good. All I can think is to double check everything is plugged in correctly but hard to say. Hopefully you get it figured out!
@grgsrvc 2 жыл бұрын
Need some break in footage. Let’s hear that new heart wail!!!
@kittybear320 2 жыл бұрын
Great video!
@themediocregarage 2 жыл бұрын
Thanks!
@hornefoundations 2 жыл бұрын
Need to invest in an impact tool!
@mikeliberatore3957 2 жыл бұрын
Good video! Bought a 2017 xcr 800 last month and unfortunately seized up on my first trip, now I know what I'm in for. Question, who should I send mine off to? Stator side is the issue, piston and head started to melt and the connecting rod seized to the crankshaft. Clutch sides power valve ears broke off too, one ended up in the exhaust, gouged up the cylinder a little. Any advice?
@themediocregarage 2 жыл бұрын
That sucks! BWC Powersports in Edmonton AB treated me really well and I highly recommend them.
@rawpoptart2046 2 жыл бұрын
Also dope video.