Thanks so much for posting this. Instructions were very clear. I had difficulty getting all the panel clips back in place, but at least the lift gate works properly now.
@gabrielcastro3630Күн бұрын
I got a honda accord 2003 2 door and I pay For the same peace and I look and look for my car and I can't find it 😕 anybody else know where it at for a honda accord 2003 2 door thank u
@jeffmcallister43594 күн бұрын
Hey has a Cummins tech at the dodge dealer for those who said how do I use the tool in the truck they make ones with small bolts you really need maybe 1/4 away from the front cover
@shuffleshuffleshuffle4 күн бұрын
Do you get any codes when it's bad?
@rtrey24365 күн бұрын
After installing the clock spring the cruise control portion does not work but, the radio control works
@rickyshaw24436 күн бұрын
Which model and year is this Honda?
@kylescott11996 күн бұрын
My Chrysler 200 2013 can shaft sensor went out I replaced the easy one on top of engine still had an issue replaced the one at the bottom and it all works now it was putting my traction control on by itself now 2 months later came shaft again think this car brand just has lots of little problems
@eddyvellvelez11337 күн бұрын
Thank you for all that information..Good information that I didn’t know 👍
@presidentmonkey1onpsn8310 күн бұрын
Just replaced one of these engines this was the problem! Thank you for this video sir 🙏🏽
@BigmoRivera10 күн бұрын
Great Job 👍🏽 Will That EGR Make The Engine Over Heat.
@americanclassix-com11 күн бұрын
Fighting a P0191 code issue ("fuel rail pressure"). Any chance pressure relief valve replacement might fix it ?
@pakkelly11 күн бұрын
Is it possible to replace standpipe and dummy plug o-rings without buying new pipes?
@truexkev273711 күн бұрын
I have rust on my oil rails. Any ideas what the problem is ??
@waveydavy111 күн бұрын
Where is this located
@pavelcuevas613912 күн бұрын
entonces al cambiar el sensor, se pierde el gas refrigerante? y se debe hacer limpieza, vacio del sistema para volver a llenar con gas?
@dominicabiyahu12 күн бұрын
Here's how you install the new DEF injector ..... next scene, the DEF injector is installed. Thanks, learned a lot from this video.
@ZacharyChristensen-u4z14 күн бұрын
Do you have to trim the injectors before starting?
@stanleymorton299215 күн бұрын
I'm not sure on the '03, but on the '01 it doesn't. However, it shows up during scan mode and may cause a B1352 dtc
@adolfoponce834617 күн бұрын
Thanks you your video help me a lot
@marcoramirez270320 күн бұрын
How can I know if my Injection Pressure Regulator it’s bad?
@jacquelinemartinez381020 күн бұрын
Where is the second one located
@yonisenoel585319 күн бұрын
That's what I would like to know
@The_Hidden_Atlas20 күн бұрын
Honestly this video was $240 worth of amazingness. I was recently quoted 255 for a 15.00 part ❤❤ subbed ty
@schluckowsky21 күн бұрын
When You install the oil rail, do YOu have to let the air out of the rail for function? Thank You. M.
@edgarlarapuga533822 күн бұрын
Después de q instalas el sensor de ay nomas la prendes h queda lista o nesecita algún otro proceso???
@juryveil641222 күн бұрын
Little late but found that starting with installing bank 1 in first is easier then bank 2 What u did to get it in the easiest and quickest was lining up the fuel injectors with the hole and lifting up the middle on either with your fingers or a screw driver and same thing for the other side. Reason why it’s so difficult is because there’s a little lip on the middle injector hole so it’s really just lift a little so it passes that little lip and then push a bit on the injector itself and then the rest should line up if not same thing give it a little push with a screwdriver Putting that middle one first makes the job so much easier but before me figuring that out it took me so long now I can get it done in under an hour or and hour 30
@lylejohnston412522 күн бұрын
This is great. Except, it doesn't show the only thing I need. How do you get the tilt lever off?
@kgosieselekgosiesele800623 күн бұрын
My Turbo has crike
@sethayers693123 күн бұрын
How the hell can I get my 6.0 to start after replacing standpipes and dummy plugs I can not get it to start it acts like it wants to its starts to turn over but it sounds really bad and want ever crank.
@s28gful24 күн бұрын
Mi RAM 3500 reguera mucho y bota el acoplen por el tanque de reserva porque ?
@windstarpro24 күн бұрын
The in person seminars are pretty good. I went to a few.
@roroperez91624 күн бұрын
La peor Marca en repuestos.
@antoineagelidis575126 күн бұрын
Exellent video thanks for your time. Tell us about pao68 for R134A, the oil made by behr today's mahle that mixes with all pags and you don't need to have all types I always flush with nitrogen.
@garybaldwin106126 күн бұрын
What year?
@ricardoleyton491326 күн бұрын
Yaa y se desconecta la bateria completa o solo el negativo y despues se resetea con el computador externo ??pon la informacion completa y no comprometer un daño mayor..
@DGZGSGEGIGKG27 күн бұрын
Thanks for the caveat at the end. I was thinking I could do this myself but it’s beyond my skill level.
@caseyschultz540428 күн бұрын
Wtf? You didn't show how to do sht
@climmetgrimes124929 күн бұрын
Thanks for the great video. Pulled injector #4 working 2 hours yesterday with this video. (I’m handy but never worked on my diesel because of doubts). Note I used a 3/4 fuel line disconnect and a breaker bar for the top hard fuel line. A real wrench didn’t work for me no matter the size due to space
@co8466Ай бұрын
Done all that but cannot turn the ignition switch key to crank position now what can I do
@co8466Ай бұрын
Done everything you say cannot turn the key to ignition crank position. ignition key will not turn so now what do I do
@JC-dd5tjАй бұрын
Does this pump is always pumping def fluid or under certain conditions are met? Because I disconnected hose before injector and no fluid is coming from the pump
@Alex-bjornАй бұрын
Para un Malibu 2006 es el mismo procedimiento para quitarla??
@seatime674Ай бұрын
Ive got the '18 Pacifica and mounted a camera to the front and these darn things stay closed even on the freeway at 210 degrees.. To HOT.. Im shaving the slats down or pulling the middle ones out so I dont get a check engine light!!!. What person would purposely block off a radiator ro run hotter deserves a swift kick in the a**
@thekiltedveteranАй бұрын
When my P-71 gets to midpoint on the temp Guage (normal range), she stalls when the car is in drive at a stop. The RPMs run at about 4 and then choke out. What would be causing that? I can keep her in neutral at a light and feather the gas pedal, but that's all that will help her from a stall. Is it a bigger issue? Also, air/heat went out not long after, not sure if that is related.
@ergoladyАй бұрын
Great video, Thank you
@michaelwilson1282Ай бұрын
If you could help . I had the Intoxalock install , now my D 4 flash’s , alarm doesn’t work , and check engine light is on with tcs. P1705 code but it’s not the transmission safety neutral switch . You seem to know your stuff . If you could please help me. Thank you