Jack Peeks Sales

Пікірлер

@allanfarr 6 күн бұрын

Your belt diagram is different than my xmark diagram.

@allanfarr 6 күн бұрын

I have and extra wheel. Wtf

@allanfarr 6 күн бұрын

I finally fixed it. Mine only has one belt through tensioner then to back then to opposite side of deck. This necessitated loosening the support for the tensioner wheel so that I could route the one belt through the tensioner support to back wheel. This was easy to loosen the two bolts so that I could get the belt through the tensioner support bracket. Your belt goes through then back the same way. Mine only goes through one time. Anyway that was the trick on my deck. Just be sure which model deck you have. Mine says Triton 46. Oh and my diagram also has the part numbers for each of the 3 size belts. My diagram was buried under years of dirt and grime but I found it.

@jbontregor6717 7 күн бұрын

Very helpful!

@tompeterson7917 15 күн бұрын

Thank you for this simple yet very informative video. This helped me a ton! 👍🏻

@bigvick2477 16 күн бұрын

Thank you!

@predator-rs5fq 17 күн бұрын

Excelente video..gracias

@jbontregor6717 20 күн бұрын

Thank you!

@rodneyyarbrough6524 Ай бұрын

I’d like your opinion on after market belts and blades

@joelovitt2900 Ай бұрын

I guess mine isn't a 50" because I can't remove my foot deck. (no stickers identifying deck size)

@michaeldozier3008 2 ай бұрын

Excellent, to the point! Great video, thanks!

@KitchenConfidencewithCK 2 ай бұрын

Fixed it! Thanks!! It was the 2nd suggested troubleshooting tip that was the trick

@briancaine9130 3 ай бұрын

Very useful. I’m going to try this on exmark Lazer S series this week. Thanks.

@schlotdoglaser 3 ай бұрын

My brand new one wasn't working. We don't use pesticides because of where we live (we have a well system). So, I use Vinegar, Salt and Dish soap. After I put in the mixture, it worked for a few seconds and then stopped. I watched your video and check and it was my doing....the salt chrystalized and was clogging the pump. I cleaned it out and it works amazing!

@MrRawraw3 3 ай бұрын

Great video

@allanfarr 6 күн бұрын

I cannot figure out how to get the belt around the tensioner wheel. The wheel is attached to the base and there is no way to get one part of the belt through the space between the base and the wheel. One part of belt runs from tensioner wheel to back wheel then to wheel on opposite side from tensioner just like in the diagram. Does the tensioner wheel have to be removed?

@user-sr9kg6cs1t 3 ай бұрын

Great Job !

@thedebumdum8268 3 ай бұрын

Ok what about the drive belt so I know how to do 3/3 of the belts plz plz

@littledabldooya 4 ай бұрын

The brass valve on mine was stuck. Bumped it with a wrench and pressure restored. Got it fixed thanks to your video. Thanks!!

@johneaton6861 5 ай бұрын

Thank You, was very informative, appreciate the instructions.

@charlieking6640 Жыл бұрын

Thanks you saved me from looking too far very helpful for me

@onthelake9554 Жыл бұрын

Show of hands : how many people buying 500i's set their saw on the ground to start it ? = none

@alanmeyers3957 Жыл бұрын

And how many use the decomp? None.

@viciousKev Жыл бұрын

Okay.

@lkjyuiop1987 Жыл бұрын

I like the ms462c better

@adrianstefan23 Жыл бұрын

🔊🔊👏🏻👏🏻

@brianbelchuk9612 Жыл бұрын

Good job

@robertodebeers2551 Жыл бұрын

Outstanding. Thank you.

@em4703 Жыл бұрын

You only need to pump the primer when the saw is cold and you want to start it. It take hours for the pressure to drop below the minimum 2 bars inside the injector lines for this to be required again, so if you stop the saw for a few minutes, you don't need to pump the primer again. Pumping the primer after every restart is a waste of time, you're just circulating fuel around and that's it. Also, you can start it between your legs like any other saw, no need to put it down in the mud, it's in the manual. Nothing is worse than giving half assed advice, just read the manual and watch the fuel injection system diagram to understand how it works, only then tell people what's what..

@robertodebeers2551 Жыл бұрын

Thank you.

Ең жақсы KZbin

Пікірлер