Just found your channel and so happy i did I just bought a new mwb crafter and am about to start conversion myself Your vids are brilliant thanks and hello from me in offaly

Very helpful mate

Do you have a part number for the factory fit covers please?

Would you have the part number for the upper parts .the ones above the seatbelt trim

Fuel sender removal tool 😢

In a promaster you don't have to do any of those things that you did in the beginning of the video. You simply take the cap off the nipple and plug

Nice

Absolute godsend - thank you for doing this video - my attempt only went smoothly thanks to your instructions and remembering your advice 'to take your time'! needed this when I tackled those damn vw clips in the visor.

Hi would you have a part number for the 180 deg hinges. and how much would they cost. Thanks Julian

Those sunvisor clips!!! 🤬

fantastic video

Great explanation I followed it and removed mine but those clips on sun visor brackets worst idea ever what was wrong with 2 screws complete overkill by volkswagen.

Brilliant stuff man! I’m right now removing my identical headliner and you’ve made the process so much more straightforward. Thanks for putting this up.😊

Legend!! Thanks so much! I couldn't of done this without your step by step video!

great vid where did you buy the replacement passenger seat from please

very helpful video!

great two vids helped me a lot and gave me the confedence to give it a go i put off doing it because everyone said it was a swine of a job but away over the new year i got the dreaded condensation dripping off the grab handles on the A post and dropping in to the cupholders. i made a toll like vw but still only manage to get one clip off had to take it to a car uphosterer i know and he manage to pick the clips out . your vids were excellent and easy to follow made doing the rest of it very easy i didnt notice till i tried to drop the lining that it is trapped behind the thing at the centre of the windscreen at the top and was a pain to work around but all in all thank you for posting it

Great explanation. Wish you'd posted it 6 months earlier though, before I did mine😄. Bugger of a job! Impressed with the clarity and lighting of the picture. What camera did you use?

Excellent video bud. Well detailed and easy to follow

And now the easy way: kzbin.info/www/bejne/haHLeYV6d9ybetksi=ycvW3FfLGw1dQUhV

Nice one

Great review!

Just had one today, and drilled a 5.5mm hole to the left of the breather, tapped it and screwed down to 'o' ring seal, in this position it's a clear run and no obstructions, easy and no mess or special tools required!

Anyone know if there's some trick to getting the breather pipe off? I've been at it for an hour and just can't get it off

Can you please let me know where you got the swivel mixer tap for the pull down basin. Finding it hard to track them down. Thanks for your help .

Great!

Thank you for sharing, wondering whats the height between bottom of the faucet to the first obstruction. Found some faucets that could fit in US, the Ambassador Model: 132-1727-CP and the Barka 2600. The first needs 5" 1/4 for the hot/cold mixer version and 5" for the cold only. The Barka needs 4" 1/4 however does not swivel up down and comes from Europe.

Excellent video, thank you, where do you get the fuel sender removal tool?

Superb video. Extremely helpful and precise. Thank you 👍

Hi Another question about your installation of the tip up sink. How did you connect your waste pipe into the rest of the waste system?

Clear as waterford clystal thank you

Any chance you would give me a hand fix mine?

Have you done a install of the sink video? About to fit 1 . ❤️ your channel

Really good video. Very informative. About to remove the tank that came with the heater and switch to main vehicle tank. Coming into summer so hopefully prices will drop soon. I haven't got sender removal tool but most people won't. Any suggestions on removing it without the tool. Thanks Jamie

I cannot work out how to remove the side panel from the base of the seat. The panel needs to be removed to get to the third screw that hold down the access hatch on the floor

Hi, I recently fitted my diesel feed into the top of the grey breather pipe ( removed from sender, drilled 5mm hole), this avoided disturbing the sender unit and chance of debris into tank. I used a smaller bore fuel pipe than that supplied with the original kit, works a treat.

I think I am missing something . I cant see the sight for the hole . for the feed pipe .

Well explained...need to re watch this when ready to go ..⭐️⭐️⭐️⭐️⭐️🙏

Where is the most appropriate place to feed through the floor to the pump?

Hi there. Am looking to install a diesel heater in a van and use the fuel in the main tank (like you) rather than a separate one. Mine is not a common van so there's not really an OEM-type solution; it's not a VW-T4/T5 sort of thing but a rare Toyota. I can see why it might be useful to install a separate pickup into the tank, especially as in your case you have a large plastic access port where you can bolt in a pickup and also limit its depth both so you can't drain the tank with the heater or pick up crud from the bottom. In my case I don’t have this ready option so I wanted to ask whether you’d thought of the option just to 'T' into the return hose back to the tank? This would be more straightforward than a separate pickup and most return hoses dip deep in the tank, too. Interested to know your thoughts, please.

Hi, can you let me know where you got the base plate with collar/tower? I am referring to the the part where the heater is mounted to the floor of the van. Thanks.

I don't suppose you have any links to the sender pick-up pipe you used? Thanks.