Diesel heater to main fuel tank sender unit peugeot boxer /Fiat Ducato /relay Campervan.

www.bowerspartsonline.co.uk/b...

[@williamwalsh347]

Excellent video bud. Well detailed and easy to follow

[@stealthkiwi1869]

Just had one today, and drilled a 5.5mm hole to the left of the breather, tapped it and screwed down to 'o' ring seal, in this position it's a clear run and no obstructions, easy and no mess or special tools required!

[@DavidEllis-ju8if]

I like this idea better. Where did you get the treaded pick up ? Did you take a photo ? Thanks

[@Yahoomediaclub]

Well explained...need to re watch this when ready to go ..⭐️⭐️⭐️⭐️⭐️🙏

[@TheWrinklyNomads]

Superb video. Extremely helpful and precise. Thank you 👍

[@montydod]

Clear as waterford clystal thank you

[@michaelstevens9394]

Hi, I recently fitted my diesel feed into the top of the grey breather pipe ( removed from sender, drilled 5mm hole), this avoided disturbing the sender unit and chance of debris into tank. I used a smaller bore fuel pipe than that supplied with the original kit, works a treat.

[@lowrider075]

Hi Michael, What fittings did you use, and how did you feel the fuel line into the tank through the breather? PM me if you would, Photos would be great. I have saved Jamie's video (thank you Jamie, great vid) but, if I don't have to disturb the sender unit, then I'd rather not.

[@michaelstevens9394]

@@lowrider075 my research was from Agora vanlife / on how to do main tank feed through breather. I fitted the diesel filter and put it on top of the sender unit so I can acess it easily for cleaning . Also view vanlife RX for alternative fuel line and pipe into tank. My fuel line is about 5m I bought an insulation too to cover the pipe before feeding it along chassis to the rear where my cdh is situated. Only one problem after a year and that was the glo plug. I wish Id mounted my cdh on its side , you tube again has lots of info on this too.

[@michaelstevens9394]

Should also mention the facebook cdh groups gave loads of tips n hints

[@daveblogs5019]

I did exactly the same..via Breather pipe..very simple..working 100% since fitting over 2 years ago.👍

[@MusicConnorThomas]

Did you do anything to seal it other than just tightening the thread? Since doing this I have had a check engine light... I'm torn whether this is because of me fitting the stand pipe in the breather hose OR the fact that the bad weather killed the battery and its since been recharged. Brand new van. In for a check on the 5th of jan.

[@Tiago850]

Great!

[@Rattlesomecages]

In a promaster you don't have to do any of those things that you did in the beginning of the video. You simply take the cap off the nipple and plug

[@stuartinns8438]

I think I am missing something . I cant see the sight for the hole . for the feed pipe .

[@stco2426]

Hi there. Am looking to install a diesel heater in a van and use the fuel in the main tank (like you) rather than a separate one. Mine is not a common van so there's not really an OEM-type solution; it's not a VW-T4/T5 sort of thing but a rare Toyota. I can see why it might be useful to install a separate pickup into the tank, especially as in your case you have a large plastic access port where you can bolt in a pickup and also limit its depth both so you can't drain the tank with the heater or pick up crud from the bottom. In my case I don’t have this ready option so I wanted to ask whether you’d thought of the option just to 'T' into the return hose back to the tank? This would be more straightforward than a separate pickup and most return hoses dip deep in the tank, too. Interested to know your thoughts, please.

[@owcampervanadventures2738]

Hi thank you for the message.. I actually think that you should probably be able to get that setup to work on your Toyota as long as no air is intrained into the t connection you create before going to your fuel filter & pump to feed your diesel heater.. You should be able to see the amount of fuel In the clear filter and because the diesel heater uses very small amount of fuel I reckon you won't overdraw the return pipe.. Best of luck with setup and be good to hear back how you get on.. 🤞👌

[@campervancreations7656]

Really good video. Very informative. About to remove the tank that came with the heater and switch to main vehicle tank. Coming into summer so hopefully prices will drop soon. I haven't got sender removal tool but most people won't. Any suggestions on removing it without the tool. Thanks Jamie

[@owcampervanadventures2738]

Hi Jamie, I would advise that you would be best to get the tool on amazon or ebay as its very easy to damage the lugs using an alternative method say hammer and wood.. Should be around 15 euros for the cost of the tool.. Be of luck with your removal and glad you found it useful 👍

[@brushlinez5884]

Hi, can you let me know where you got the base plate with collar/tower? I am referring to the the part where the heater is mounted to the floor of the van. Thanks.

[@owcampervanadventures2738]

Hi ButlerTechnik. Com.... uk company that ship worldwide around stg £ 23.00 ... Make sure to use fire resistant silicone.... Works perfectly

[@mikehall-hall2858]

I cannot work out how to remove the side panel from the base of the seat. The panel needs to be removed to get to the third screw that hold down the access hatch on the floor

[@owcampervanadventures2738]

Can you attach photos as unsure of issue you have

[@pau1phi11ips]

I don't suppose you have any links to the sender pick-up pipe you used? Thanks.

[@owcampervanadventures2738]

Hi Paul, I used Bowers to get my Eberspacher fuel pickup pipe kit.. www.bowerspartsonline.co.uk/brands/eberspacher/fuel-system-parts/eberspacher-heater-peugeotcitroenfiat-iveco-fuel-tank-sender-standpipe-kit-292199018093 Really good kit and works perfectly with no issues.. Hope this helps

[@bobbyfischer6786]

Thanks very much for video very helpful. Did u disconnect the battery b4 or just beast in?

[@danclark7191]

Where is the most appropriate place to feed through the floor to the pump?

[@owcampervanadventures2738]

Hi the best place to run the line to pump without any further drilling etc is to go through the gap at the top of the diesel tank which is beside where my fuel line runs in video.. I also used protective conduit for 100%protection.. Hope this helps you.. 👍

[@amacmedia3221]

Excellent video, thank you, where do you get the fuel sender removal tool?

[@owcampervanadventures2738]

Hi, Amazon sell the fuel sender removal tool approx 14 euros

[@amacmedia3221]

@@owcampervanadventures2738 many thanks for this

[@ShadowV]

Anyone know if there's some trick to getting the breather pipe off? I've been at it for an hour and just can't get it off

[@owcampervanadventures2738]

Hi , They can be stubborn to remove.. maybe get a hairdryer to warm up the breather pipe and it should make it a bit easier

[@michaelwoods6218]

Any chance you would give me a hand fix mine?

[@owcampervanadventures2738]

Are you in Ireland or could help over what's app

[@DuncanAtkinson]

Fuel sender removal tool 😢