Thanks for sharing.please post more videos when you do more repair or services. ALL BEST WISHES.
@HaraldHovathАй бұрын
how to get the planetary cup off after removing the 2 thumb srews?thank you
@calucoelsv28 күн бұрын
Hi there You can try with a rubber mallet, if that doesn’t work where the holes in the ring are you can use a center point in the cup and slightly hit the hole where the screw you remove will go, that should lose it allowing you eventually to remove it Hope this helps
@gorduroygordonskyАй бұрын
Jose buenos días una consulta usted vende toda esa pieza del clutch
@calucoelsv28 күн бұрын
Hola buenas tardes Depende lo que nesecite Se refiere a los discos oh a la armazón que contiene los discos? Si me da detalles de exactamente lo que Nesecite puedo ver si lo tengo
@gorduroygordonsky25 күн бұрын
@@calucoelsv a toda la armazón que contiene los discos
@gorduroygordonsky24 күн бұрын
@@calucoelsv yo le escribí al correo que aparece en su perfil ! O si tiene otro correo me lo puede proporcionar para que me ayude!!
@lglezf951062Ай бұрын
Como removió la tapa que cubre la transmision? Hablo de la pieza donde va el planetario
@calucoelsvАй бұрын
Eso si es buena pregunta Es bastante complicado Pero recomiendo se asegure de remover todos los tornillos ahí en el vídeo lo explicó Para remover una vez hallan salido todos los tornillos, con espátulas y desarmadores planos martillo, y a darle con paciencia eventualmente sale
@lglezf951062Ай бұрын
@@calucoelsv usó algún "puller"? (no se como se llaman en español)
@calucoelsvАй бұрын
@@lglezf951062no use nada especial pues no hay extractores especiales solo creatividad unas espátulas y paciencia
@lglezf951062Ай бұрын
@@calucoelsv gracias hermano. Trataré de reparar la mía
@aecommercialequipmentrepai8031Ай бұрын
Hi, what paint did you use?
@johnnybald53582 ай бұрын
Hi Jose This is a good Video 👍
@halcyoncmd2 ай бұрын
As a Hobart technician, i applaud your ingenuity with a situation where many techs would either try to cut the planetary off and replace it, or declare the equipment unrepairable.
@calucoelsv2 ай бұрын
Hi there thank you for your comment We do our best to help our customers we will not give up until nothing can be done, but for much simpler reasons some technicians will condemn a mixer Not our practice we try our best and most of the time we resolve and fix the problems with the mixers
@jantoniosegovia47572 ай бұрын
Tendrá lo engranes de echenike de 20
@farenkeogh28902 ай бұрын
I have a mixer that randomly shot off power. Will you do a video of one that will explain it. Thanks in advance.
@lazarovirgilionaranjo24122 ай бұрын
Hermano, ¿donde radican ustedes? Yo sueño con una jobart y quiero saber donde están ustedes.
@calucoelsv2 ай бұрын
Hola buenas tardes Nos encontramos en San José california Espero un día se le conceda tener una de las mejores mixteadoras americanas con mas de 100 años fabricando maquinaria de calidad
@jwbrit3 ай бұрын
You should periodically grind the mushrooming off your drift, when it gets very bad pieces can spall off at high speed and cause injury.
@calucoelsv2 ай бұрын
Thank you sir for your comment will take it into consideration highly appreciated it I already have seen a video where a guy recommends to pay attention to the mushrooming of the tools that we use with manual impact Thank you again God bless!!
@tjs_welding_and_fabrication3 ай бұрын
I deal with rotation for 3 phase hydraulic pumps as well. As you state many dont pay attention when wiring.
@tjs_welding_and_fabrication3 ай бұрын
Great vid. Why do the shafts rust there. How is moisture getting in there. I would assume anti sieze compound is used liberally on the shaft for the next guy.
@calucoelsv2 ай бұрын
Great question Is hard to know I have encountered this issue more on mixers from the 80s more often than the much older units like mixers from the 60s I don’t know why maybe the quality of the material on the main shaft is not the Same as the really old ones .
@gato61003 ай бұрын
disculpa una pregunta en las hobart hl600 legacy, como se yo si son de 1 o 3 phases, la placa de hobart dice 1 phase y 3 phase, pero hay otra placa que dice que la maquina esta puesta para trabajar en 460 v 3 phase. Mi pregunta es que si estas maquinas las puedes trabajar en 1 phase y o en 3 phase nomas cambiando las lineas de electricidad que vienen del motor?
@calucoelsv3 ай бұрын
Hola gracias por tu pregunta En la hl600 legacy en el data plate dise 1ph or 3ph es bien simple de saber ejemplo si la quieres usar en single phase no se usa la linea 3 solo 1&2 Ahora no estoy famirializado en legacy’s con el voltage 460 Que imagino Que hay pero no se las configuración Solo se en el modelo h600 que se puede usar a 230vlt 3 phase oh ah 460vlt en ese el motor trae el diagrama para aser el cambió pero repito en legacy en 460vlt no te sabría ayudar
@gato61003 ай бұрын
nice but use automotive paint is better to work with and leaves nicer finish and coats better and price is about the same.
@calucoelsv3 ай бұрын
Off course I agree auto paint will give me a better finish and protection As it matter of fact I use to paint 15 years ago But here in California solvent paint is illegal since 2010 if am not mistaken now is water base paint and if you know about painting water base paint for vehicles is a bit more complicated to use than solvent, that’s why for now I use spray paint, I know for a fact from another dealer that does takes his mixers to a body shop literally his spending a bit over $1500 a unit so here in cal is expensive to do it that way that’s why I rather do it this way and pay special attention more to mechanics in the motor And transmission in the long run that’s what matters more than a fancy expensive paint job Do appreciate your opinion thank you sir.
@LuisFernando7533 ай бұрын
QUE TIPO DE ACEITE USA ESA MAQUINA ??
@calucoelsv3 ай бұрын
El aceite que usa es el EP460 extra duty gear oil no es cualquier aceite si no este que le mencionó
@osamaibrahem633 ай бұрын
So you have any idea why when installing the worm gear shaft in place it's loose and probably doesn't sit , and keeps moving? H600 Thanks
@calucoelsv3 ай бұрын
You need to be more specific Example at the bottom the bearing is self aligned so it moves its design that way on h600 so once installed it’s going to move sideways but once everything is assembled the worm gear shaft will be pretty tight, I understand that this might be what you are talking about it if you refer to something else write me again will try to figure it out.
@osamaibrahem633 ай бұрын
@@calucoelsv yes this is what am talking about, but when everything is assembled and I put flour and start it the gear just moves away from the motor gear and don't turn the other gears.
@calucoelsv3 ай бұрын
@@osamaibrahem63i that’s strange my friend Next steps would be to count on every gear all the teeth I could help you with the parts manual but you have to find a way to contact me trough WhatsApp my phone number is in some videos
@abaidrehman48833 ай бұрын
You are a good teacher Thank you 😊
@tymz-r-achangin3 ай бұрын
Was interesting to watch. Thanks for the video :o)
@d.mmaropack14804 ай бұрын
Good job
@ParLee-ex3ym4 ай бұрын
Hi. You take cash for part and service only, we have check from company, where your location in San Jose?
@jonathanavalos52974 ай бұрын
Como se saca el aceite y se hace el cambio
@hugogaldames41564 ай бұрын
Why lay it down? Most of don't have this option. We fix these on site. Can't you hammer it standing up and have gravity help removing the planetary,?
@calucoelsv4 ай бұрын
Hi thank you for your comment In regards of laying down it works for us perfectly, you can do it with out laying down, is just a bit more challenging but it can be done. You can also try with an extractor but it’s also challenging, that’s why I don’t bother to try it with an extractor but the option is there.
@kheng-49394 ай бұрын
Hello My friend
@calucoelsv4 ай бұрын
Hi there!!
@hugogaldames41565 ай бұрын
Where do ya get the parts?
@calucoelsv5 ай бұрын
There should be available at Hobart parts.com In this same website you should be able to look for any Hobart mixer manual
@kevinstier49535 ай бұрын
LOL WTF did someone decide it was a good idea to put the mixer outside?
@calucoelsv5 ай бұрын
No they didn’t left them outside They had a cleaning service company to clean their kitchen they have like 12 140qts so I guess is much easier for the cleaning company to pressure wash their equipment including the mixers…
@wujianrang4325 ай бұрын
Hi sir l looking for a Hobart mixer d 300 agitator shaft
@wujianrang4325 ай бұрын
Because I see you have a lot there hope you see this message
@calucoelsv5 ай бұрын
Part should be available at Hobartparts.com Part #00-913102-00306 price is $788.33 taxes and shipping not included
@ladyluck30965 ай бұрын
5500 ur crazy
@ivanl86136 ай бұрын
Buen trabajo amigo !!
@reubengarcia47736 ай бұрын
That Raptor stole the show. I've never seen a fighter jet do the Maneuvers the Raptor showed us. Incredible Fighter Jet we have. 🙌👍
@adrianp30986 ай бұрын
Was there Saturday, cool to see them use flairs.
@RadOn60FPS6 ай бұрын
Hands down the best and the most lethal Fighter Jet built to date💯🔥
@bbaff86226 ай бұрын
Was there both Sat and Sunday. Great show.
@ryand45336 ай бұрын
Looks like it’s just floating around. What a machine!
@559mud-mafia6 ай бұрын
I went there
@jorgeruiz35827 ай бұрын
Estimado Jose, tengo una mezcladora hobart H600 que no esta trabajando en tercera velocidad, te agradecería si me dieras una pista de lo que puede ser el problema. Gracias.
@calucoelsv7 ай бұрын
Hola buenas noches Suena como que estuviese quebrada una cunña en el piñón de velocidades pera a la vez pudiese ser algo más pero bien posible una cuña que controla la velocidad creo 3ra y 4ta también no estaria trabajando si es la cuña que digo Hay una forma un poco peligrosa de saber pero si la 3ra no funcióna no pasa nada se trata de prender la máquina sin nada y poner 3ra y tratar de agarrar el planetario con ambas manos si lo logras detener es una cuña si no será algo más espero y esta breve explicación te ayude
@calucoelsv6 ай бұрын
hola buenas noches es muy posible que una cuña en el piñon donde esta el engrane de bronze se halla quebrado, por lo general un 99% siempre es una cuña en ese piñon pero también pueda ser algo mas pero me inclino por una cuña quebrada, eso suele suceder
@josueceron47887 ай бұрын
Hola Jose. Gracias por compartir este video. En q Estado se encuentran?
@calucoelsv6 ай бұрын
en california en San José ca
@40mmcomboplatter7 ай бұрын
Were you getting a bad smell while using the dough roller
@tdtimothy7 ай бұрын
Great video Thanks. Any video or suggestions on engage lever falling on its own. Spring is good .
@calucoelsv6 ай бұрын
suggestion is replace all 3 screw spring assy part # 00-103652 that is my suggestion could something else that would be what I would do hope this helps
@zacolean14198 ай бұрын
A lot of help thank you
@CurrentWay9 ай бұрын
Fantastic video. Parts are apparently no longer available for my C-100. It is leaking oil from the front auxiliary port. I would think gaskets and such are pretty standard in size for this simple area. Any thoughts on how to keep / revive this mixer without buying new?
@josephwinner53769 ай бұрын
You can tell by looking in the gearcase that it has very low amount of grease and the Hobart #2 grease is too thick and bunches up in the corner and causes premature bronze gear wear because it doesn't flow around the bronze gear. Use Marfax 0 or 00 grease make sure the gear box is full. The bronze gear will last a hell of alot longer without any leaks also. Use Hobart #2 green grease in youre enemies machine!!!
@calucoelsv9 ай бұрын
Thank you for the tip 👍
@clivechotalal7199 ай бұрын
why would oil come out at the top of my L800 mixer at the large lock nut
@nickserbes9 ай бұрын
pietro berto thank you...
@FranciscoMartinez-kd6ij9 ай бұрын
Jose muy buenos videos. 2 preguntas mi mixer 140 cuartos esta perdiendo fuersa que podra ser y la otra como cambio la caja del elebador. Gracias
@hansnunez500210 ай бұрын
Where did you get the parts manual? I used to have one, but my dad lost it.
@topbunnbakeryequipment58218 ай бұрын
Google it
@martingonzalez802010 ай бұрын
Hola Jose , quisiera a ver si puedes ayudarme a cuál sería la manera correcta de cambiar el gear lower worm shaft 17 tooth ( parte es 00-121382) tendría que quitar todo el engranaje de transmisión y el de clutch también ?
@martingonzalez802010 ай бұрын
Es una Hobart L800
@martingonzalez802010 ай бұрын
Es que me está fallando las velocidades 1ra y la 3ra
@MohamedSmati-eq8bd11 ай бұрын
ممكن فيديو حول HOBART PF. 601
@MohamedSmati-eq8bd11 ай бұрын
Possible video or PDF file about HOBART PF. 601
@kevinstier4953 Жыл бұрын
The M802 and the V1401 have very close spring tensions one is 3.5 turns one is 4 turns I always have to look it up before I do the adjustment..................Hobart Tech for the past 25 years.