Thank you for the video and the perfect camera angle, about to dig into my Husqvarna 55 and see what's going on. Been a very long time, it's over due for some deep cleaning and maintenance
@alfonzoidalgo909115 күн бұрын
Saludos
@jameskaiser106924 күн бұрын
Would be helpful if you actually spoke during your video also or did voice overs afterwards
@mtdtechhАй бұрын
Very helpful! Thank you!
@ricklarner9263Ай бұрын
Looks great, thanks! just picked up one this last weekend to restore!
@WinterGameplaysАй бұрын
so..my shock it's doing a weird knock sound when you compress it. It just came back from service... but before the service was already with that knock. It's very weird because you can actually feels something grabbing the travel when the knock happens.....i really don't know what can it be. I read something about the IFP that can be wrong, but I don't know how that would cause a knock on the shock....
@BoltronixSystemsАй бұрын
In 2023, I replaced a motor in a fan like yours with a Mars Azure 10858. Ended up being way more energy efficient compared to BAF's original factory Genteq/GE motor and I was able to use a low power rotary switch for each of the 5 speeds since it had just a 24v input signal. I also used the Azure App to dial in the torque or RPM per speed tap for very low whisper quiet operation on the lowest tap. BAF's choice of motor for this fan was a bad idea. Should have done their research. If they did, they would have known the number of failures we here in the HVAC tech field have came across and replaced. At one point, we had a 50 gallon drum full of failed Genteq ECMs. A third of them had separated rotor magnets, some with shorted stator windings, dead shorts from blown high side module capacitors, the list goes on and on. If you replace the motor again down the road, consider the motor and model above. I'm almost through the 8th summer on a Sears & Roebucks Homart (formerly belt driven) fan using the 10860 Azure.
@Sockets_and_SprocketsАй бұрын
Thanks for this comment. I looked at using another ECM, but wasn't confident on how to control it. Most of them seem to use a 24v input signal to the tap wires. I guess that's because home thermostats use 24v signals to the unit? I wasn't sure how to accomplish this on the fan. Wouldn't I have needed a 24v power supply input to a 5 position switch with the outputs going to the motor taps, and then 120v going to the motor directly? I figured it was possible, but didn't want to spend the money on an ECM motor and power supply and not be able to figure out how to make it work.
@BoltronixSystemsАй бұрын
@@Sockets_and_Sprockets I like the low voltage control and it looked like that box had enough room for a transformer. Wished I had seen your video earlier. I'd show you how to hook up. The Mars Azure motors have a slow ramp up time which I really like. It's not a whole bunch of air on you at once.
@clutch5sp989Ай бұрын
Your mom is gonna spank you good for using the kitchen sink to clean parts. I used my mom's 12-quart stock pot to boil the block & other aluminum parts clean.
@YoavZuriАй бұрын
Thanks for the video! Can you share the motor part number?
@philliphall5198Ай бұрын
It’s a must to have a generator now Just the saving of food will pay for it soon 😊 Try to plan for a outages because 10 days without power is hell Ask Houston Texas folks 😢😢😢
@milagrossmith48912 ай бұрын
Great video and to the point. I wanted to add casters to a heavy file cabinet I’m using as a tool chest. Thanks
@billkane16972 ай бұрын
Great video, where did you source the bearings, seals and clips for the gearbox rebuild?
@west_side_ian5232 ай бұрын
🖖😎
@221neptune2 ай бұрын
What is the o'ring for ?
@quiettime687125 күн бұрын
Help hold the hose. My 322L has one inside the tank for the filter but not at the carb
@vandalsgarage2 ай бұрын
After pulling out the destroyed bearing out of the gearbox, I'd be inclined to use zz bearings instead of 2rs. Lots of great work here
@carolduncan77042 ай бұрын
I own a similar vid mar I bought when my plant shutdowns. I added casters to one at work, if you do this most will need a step stool for higher drawers.
@johnlong7752 ай бұрын
Rebuilt my rancher 55 and will not start. New carburetor, gasket, air filter, fuel filter, tank vent, ignition coil and plug. Has good fire to plug. What’s next, Help!
@Crankshaftcolton3 ай бұрын
I had this same exact engine
@Crankshaftcolton3 ай бұрын
Bro made a homemade ring composer good vid
@alexanderjohannesson58673 ай бұрын
Wd4 in the honer 😂😂 never sen that
@matteotassone95783 ай бұрын
FINALLY A WELL ILLUSTRATED VIDEO ON THIS OLD FORK, i'm searching around from a while! Since I refuse to swap this amazing fork this is going to be really helpfull
@jackiewatkins74783 ай бұрын
Did you remove the ring and clean the piston, or did I miss that. I have a homelit blower that looks very similar and has no compression all I see junk around the ring and cause it to be stuck in pistons, I would think this has to be my problem.???
@graeme17443 ай бұрын
Some people will never understand the feelings of something starting again
@shitboxoffroad3 ай бұрын
Whats the fuel mixture for these?
@ifrainjimenez88574 ай бұрын
What was the cost on the rebuild? By the way great video thank you for showing the process 👍
@Gleone584 ай бұрын
I’d recommend investing into a torque wrench. Cringed at the con rod and head installation.
@margertogletree55454 ай бұрын
Thanks for keeping it simple.
@AlanMedina3144 ай бұрын
Thank You for this no nonse approach to a complete rebuild and repair of this little workhorse.
@BobGilmour-rl2df4 ай бұрын
I am rebuilding one of these atm The flywheel has a woodruff key, like the one in the video. The points cover says "Caution Do not use a steel key. See Instructions" as doe the cover in the video The key that came out looks to be steel. What am I supposed to use? Is there some other kind of key than steel? Thanks to anybody who can shed some light.
@g41thomas5 ай бұрын
You would be better off order a new motor from Grainger
@pappy69pappy5 ай бұрын
It’s called show & tell!!!!
@paykus345 ай бұрын
Need sound
@patrickbailey22635 ай бұрын
nice video. had no idea the tank vent was there
@JeepITguy5 ай бұрын
It would be helpful to tell us what you were doing during the initial run test when making adjustments. Sounds like adjustment to the low end screw?
@carl24405 ай бұрын
Good job
@BoatLifeNation5 ай бұрын
Which screws are which? I have it running and idling but then I rev it wants to bog down. I have the idle screw on the black part, then the screw on top the small flat head one, then one on the side with a spring on it.
@andresmartinez-er7kq6 ай бұрын
What year is the suspension?
@Sockets_and_Sprockets6 ай бұрын
This is off a 2015 Trek
@robcole3326 ай бұрын
Why did you not lap the valves
@Dnasty16 ай бұрын
Hey great video. I wanted to add castors to an enclosure i'm making but I wanted to use 5" wheels and give it about 3 more inchest of height. What is the best way to go about this? Just put some wood squares above the caster mounts?
@Wolfgangschmidtnz6 ай бұрын
I know why you filled the tank before installing it.... cause you could 😂
@matthewhewson6 ай бұрын
Any chance you can email the “older” service manual?
@danimal09216 ай бұрын
LOL You washing those greasy parts in the kitchen sink just made Greta Thunberg soil her pretty pink panties!!! "HOW DARE YOU?!?!?" 😂🤣😂🤣😂🤣 Great video! I especially liked your piston ring compressor!!! GREAT IDEA! !!!!
@ninjaturtle6 ай бұрын
Good job dude. Appreciate the included struggle. This vid helped.
@davidruiz53837 ай бұрын
Amazing, that's what is called talent; thanks for sharing and God Bless.
@mountaindewdude767 ай бұрын
That's too cool! That generator cleaned up real nice! Great work!!!
@marklengal99907 ай бұрын
What it the adjustment screw on the from of gear box cover? On my WMC 712 it looks like a rachet end
@Sockets_and_Sprockets7 ай бұрын
I don't remember any adjustment on the front of the gear box cover without going back to watch the video. I do believe there is a breather threaded into the cover - could that be it?
@Bestruction7 ай бұрын
Did you sell it
@Sockets_and_Sprockets7 ай бұрын
Yes, it's been sold.
@Bestruction7 ай бұрын
Loved my goped growing up. Bought another one 2 years ago. 35 with 3 boys, want them to grow up and ride it
@goldentrowel19687 ай бұрын
Where did you buy all those gaskets and other parts like the muffler buddy