I just got 285s and they still scrub I have the same flares as you and have had to cut away a fair bit on the drivers side but not much on passenger side.

Awesome job Colin and Dan .

should've got strut spacers aswell

Make sure you degreaser it first mine was cracked turned into a double job

Hi Dan thanks for sharing. Mine is doing the same 2007. How much did this cost to do yourself please? After watching your informative video, I am contemplating it. Did your dad have to do anything else in the way of cleaning where the gasket went other than the scraper and vacuum please? Thanks once again

Cheers mate. Thanks for the video. I need to do mine and I was a little unsure on torque settings. As I don't want to crack my cover by over lightning the bolts. Thanks mate. God bless.

Fuck Toyota for making plastic covers seriously!

What is the diameter of the steel pipes used? What wall strength?

Hey mate just wanna ask after putting my rocker cover in found out my gasket were out and then i take out the rocker cover again but when i was taking it out i found my fuel injector seal got broken all 4 of em what could be the reason for that bcz i tight em without a torque wrench

Great video! I'm looking at doing this too to replace my injectors. So am I right in thinking that despite loosing the 2 fuel pipe clamps, there was not enough flex in the pipes to be able to manoeuvre the rocker cover off, and you had to loosen or disconnect the pipes at the common rail?

Did you need to use a scan tool at any time was there any codes on the dash

Awesome video is very informative. Great work Dad

What size are them fresh muddies on the photo?

Looks good mate! Top job!

watched one of your old vids last night did you end up doing the mount chop and getting the 33s to fit or did you down size

Ripper job. Looks amazing!!!

U want a little hole at bottom of the tube to let any condensation build up out other why it will build up inside and with rust out the hoop from inside out

Hey mate just wanted to say thanks for making this video. Gotta install one of these kits tommorow. its always good to watch someone do it first YEWWW!

so greatful i have a hoist

Good job! Great attitude when you realized the fit wasnt right the first time. I didn't actually need to watch this video because I was looking for another type of infill panel, but I'm glad I watched anyway. Praise god!

what thickness ply have you used about to make a floor in my canopy but unsure what thickness ply to use and be strong enough for 60ltr fridge on slide and draws without risking pulling screws fridge will likely be the heaviest thing in there

Hey mate i run a superior 4inch lift with there uca, i run a 285/70r17 maxxis razor on a sr5 rim they are a +35 which surprisingly do fit with a bees dick of scrub, my castor isnt moved forward and i dont not have a body mount chop either, let me know if you want any more info

How’d you get all the seals in the whole way?

Hey mate nice rig, is that on 31's?

Looks great mate maybe a business idea for you fitting out people's canopies? 🤙

Hey Dan where your 2 bolts hard to come off to that rear bracket?

Legend. Followed step by step and replaced mine no worries. Thanks sharing.

What did u use to make the draws slide without runners ?

Great work, looks like your enjoying the biuld, well done

Well done

Hi how did you secure ply to the roof

What size is your canopy?

what size are those pipes?

Is it just a TC box?

Looks great mate Could you right down all the measurements, cheers

You may need to run the neg lead for the inverter to the work side of the shunt or you won’t be able to see how much it’s using on the monitor. Which also means you may need to use a bigger guage wire between the shunt and the battery. I’m no expert so please do some research before any actions taken…

I was wondering if I could ask a question about heat inside the canopy. Do you have any issues? Do you need any ventilation? Do you notice the fridge struggling on hot days?

"Costs a fuckin heap"....pure Ballymena bai, no doubt that sentence was said so many times by yer da when you were growing up it has permanently eradicated your ability to sound Aussie when saying it.

Dan did you make those mud guards mate? I am going to make a set like that for my HJ45 and was wondering if you had a video on it? Tray is looking sick by the way

Inspiration plus watching this! Top job. Really like your work and attitudes mate. Please keep up the good work.

i am looking to make a winchbar for my Lux, anybody done one that could share?

Positive 30 offset on a 7 inch rim with a 10.5 X 33inch tyres and no scrubbing on my 2006 sr5 no body chop needed

I enjoyed watching all these vids. Great job mate

Thanks for the video on this it's so helpful

Where did you get the shop manual? Great job 👍

Hey mate did the swaybar kit come with the diff drop kit?? Did you end up needing new bash plates to counter the lower arms?? Thanks mate

How did u fix all the timber’s together with a second fix gun and nails?

Great job Dan

Hi Dan where did you buy the sway bar relocation bracket from?