Yeah, well, you know, that’s just, like, my opinion, man.

Yes you can use Arctic mx4 for the vram and vrms but i would recommend whaever your laptop used for example thermal pads or thermal putty. For thermal pads you have to be careful of the pads thickness.

@@nunoxu9696 its melted can't differnentiate between thermal pad and thermal putty so ordered k5 pro for varm and vrms watched bobofalltrades channel he used same like that and temps for really really low after repasting so i am gonna go with k5 pro for vramand vrms

Bro , he did the right thing. It is not worth the risk to use liquid metal for 3-4 degrees. You risk fucking up your entire machine. Better go with thermalpaste or thermalpad.

@@Chronox2k4 Chill bro, I'm not saying he's wrong. I'm just saying that he downgraded his thermal paste.

Love your videos man, incredibly detailed and thoroughly researched.

Please do some updated vids of new best putty

@steezegod2768 Will try to make dedicated videos from some more putties. I've got streams of them all so folks can see what they look like for application. The result charts are located at the Google Drive link in my video descriptions (Test Chart Repository >VRAM TIM<ETCHASH).

​@@snarksdomain Do these putties dry out and degrade cooling performance over time, just like the pads? I'm looking for a permanent solution so that I don't have to open up my GPU constantly.

@@user-f1ff23 The depends on the quality of the Silicone OIl used as the carrier fluid. Some are better than others. The Putty that set the bar high so far has been TG-PP10 (Discontinued). Many of these other putties are much newer so we don't have great long term data on them yet. Honeywell HT10000 is good for at least 2 years so far (from what Eugeney_KH told me of his customers' experiences). Upsiren UX Pro Ultra was still soft for me after 16.5 months in my laptop. TG-PP10 was soft after 2.5 years use in my 3090 with Copper shims. We should have an idea over the coming years as to which ones can match the longevity of TG-PP10. That being said, even once putty does stiffen it should still transfer heat okay. The trick is to pair it with something on the core that will last just as long, and for that I recommend Honeywell PTM7950 or similar PCM.

There are a million better putties than k5 pro. This person has done significantly more research than yourself.

@@danielphillips1171 on this particular laptop k5 pro works the best, its the closest you're going to get to the stock blue stuff Asus uses. most users eho get bad results either use too much off it or too less. there is a perfect balance and it works really well paired with Conductonaut for CPU and MX6 for GPU.

Factory blue stuff Is laird 607

K5 pro K>5,3 W/m.K vs UPSIREN UX Ultra PRO 16.8W/MK 😉😉😉😉😉

@@pvim You want her to use a worst thermally conductive paste? That's nonsense, she did great research, and execution (while having to redo it) shows excellent results. Downvoting that opinion fs.

the gpu got too hot and shut off the computer due to making zero contact with the heatsink. the thermal pads were too thick. it's easier to just use paste on the vrms.

Провода = дроч

I’d say that open source firmware mods are usually better than stock in ways that they fix the problems that the original devs left behind (that is when they’re mature enough, for now I’m staying on stock). That, or maybe if you enjoy tinkering yourself. Repairability is great but it seems that the smaller something is the smaller are the chances of it being repairable.

Yay! (No idea what to do with a tablet so no thoughts)

Slave labor… With me being the slave to the dolphinarium XD

@@agathakazar just tell me which website to report

Heya, assuming you’ve tried another SD card and it behaves in the exact same way, it sounds like a hardware problem. What caused this problem? No idea, my device will only start detecting the SD card when it’s pushed into the slot past the body. Since you mention saving data I’ll assume it worked some time ago and now it doesn’t. Did something happen inbetween? Could there be dirt inside the SD slot?

Is your micro SD card formatted correctly to exfat or fat32

Lol

Yes, actually the speaker is on the separate smallish ibutton PCB. The one with the thin flex cable, long pins and the IR diodes.

The little springy thingies? They should be soldered to the small pcb and they need to be conductive for the ibutton stuff to work.

Replacing it shouldn’t be too hard, but getting a screen that works might be. AFAIK they’re still not selling any replacement parts, and the screens were ordered specifically in bulk. You should totally poke their support though to show that there’s demand for things like screens and batteries. If you get your hands on a replacement screen you might need a soldering iron to to de-solder the old one at two points (I think they’re not only holding it in place but supplying power to the backlight as well). Also it might be just glued to the backlight part somehow, not sure about that. The flat flex cable is easy to disconnect and reconnect. P.S. the screen PN is ERC12864FAMF03-1-S7 by EastRising.

@@agathakazar Thanks alot for your reply. if i know pins or model number, my be i can search on Ebay. It should be standard screen. and ebay if full with rresbari Pi and other etc screens. What you say ?

Here’s a link to the data sheet: www.buydisplay.com/download/manual/ERC12864-1.3_Series_Datasheet.pdf I think Flipper screen is “amber”

Возможно где-то в Китае (официального магазина компонентов нет)

Dunno, sounds pretty hard, but the schematics are open source

Though of the same thing... everything is fine but that's the alternative hardware for rfid

Heya, you should email [email protected] and ask for a replacement, battery gauge problem is a well known case afaik.

want to buy myself one as well though i’m not broke, just worried i won’t get it. Customs in many countries have been seizing them, and paypal froze these guys accounts (they were only using paypal) so it’ll be a long time before any new shipments will go out more than likely if at all.

Don’t wanna risk them breaking

@@agathakazar ur nails?

Yep, the reason I was wearing gloves for the video was they were a mess at that time