What exhaust set up?

Awesome video bro, im installing mine tomorrow

What about the spacing between the torque converter and flex plate

Yooo is that a 1 piece exhaust?

Why you call the bolts screws 😂

Very helpful I’m use to older vehicles having that dust cover or whatever under the flywheel my 02 Yukon did not so I wasn’t sure how to go about that. Saved me so much time thank you!!!

I recently bought a 07 trailblazer SS. I actually ordered the struts but now I need to get the upper control arms. It was lowered from the previous owner, but it rides like shit.

yessir

Awesome bro,thank you for the video

Great video I need to do this to my trailblazer ss

Missed a few important steps

hello plz I have 4l60e on 6.0l gen 3 I have a transmission problem R n 1 working verry well 2 n 3 n 4 don't have a power on hight Rpm more than 2000 start to slip when I give a little throttle more than 2000 rpm starts to slip shifting down slow shifting a little by hand i have slow shifting between 1 n 2 , 2 n 3 , 4 with slipping when rpm start to more then 2000 I have rebuilt it and same problem you think torque convert ? thank you

I think very good video and in plain terms .. Very informative and well done explaining step by step illustration ..Every job will have its problems and quirks but you hit the basics pretty good. Thanks

Firme

Where can I find that plastic cover that sits infront of the starter?

Future. On LS flywheels have a pilot hole put that bolt in first you don't have to keep rotating it

How about the gap between the flywheel n torque converter

Might wanna replace the rear main seal and gasket since you are this far along...

Good video you with the TBSS Society?

amazing video ! just ordered struts and upper control arms !

If in truck do I drop driveshaft and disconnect all lines?

That thing sounds awesome 😎

Hey was that a AWD TBSS you cut your front shafts?

Nice vid thanks for the help

Looking good 👍

hey bro i have 1998 silverado currently putting efans but im stuck on the part where the green and wire go to the pcm its alot different from 99-03silverado that ive done wondering if you can help with that

Hello my friend.. Thanks for the video ... can you tell me where did you get the Hernes The one you are using in the video. Thanks for your time have a great day

I tried to watch this video but couldn't cause how slow you talk man

I did this upgrade and bought a aftermarket harness. Only one turns on then both at temp?

Swap and flip control arms

Amazing that dealership gets $1,200 for this swap

Part # for the upper control arms?

Wett

U got the part number for the upper control arms ?

Sounds badass man 👍🏽👍🏽💯

Thx for the info

Thank you!

Random question; did you leave the bump stops up front?

I'm doing a 5.3 4L60e btr stage2 cam..tbs intake. 102 mm throttle body..

How much torque converters cost when you doin a ls swap?

Is there NOT a bolt stud (for the bell housing to the block) in the 1 oclock position? I see one at the top at 12 oclock and one at like 3 oclock. Is it just missing or not needed? At 11:32 you can see what I'm talking about. Thx.

I like this truck did you finish building it ?

So yours had a plastic piece in front of converter, mines got a metal piece?

Wat size drop

Thanks for the ez video helps a lot hope u keep the videos going 👍🏻

Did it turn on and stayed on without a tune right after the cam swap ?

Make sure you retune it so you're not running lean.

Which headers you running? I ordered some speed engineering ones for my truck

Hold camera correctly i had to stop 1 min in. And also. Those 13mm are studs with 15mm behind them

Add fluid to your torque converter before installing Also stop for converter bolts did not fit It's easier to check fitment size prior to installing