Hi, Mostly pressure and a little glue. Just needed to stop the back and forth movement, and really could have gotten away without any if it wasn't for the trim i was adding. Tried to avoid screwing the visible side of the cabinet. GL!

Was around $12 a panel.

Will let my decorating manager know ha ha. Ty :)

Yes definitely doable, just would have taken me twice as long. Ikea just had finished drawings, shelves, rods, inserts etc. We just wanted something in faster but definitely doable from scratch. There are a lot of jigs now that can do the same thing if you have the time and patience to do it... maybe next closet we will try from scratch ;)

Hi, I did 8th from the top, (1 above my shelf location so it was hidden when looking from the ground). Then I did 3rd from the bottom ( i am sure fifth is fine - if you don't have any shelves going there) and 24th from the top (middle-ish) to close the gap. If you are not adding trim i would just take a couple small clamps if you have them and see what areas need it and will close the gaps before committing to any locations. GL!!

Thanks! It's woven fabric not screen printed so the design shows up on both sides. Price was great and Canadian dollars! We found it on clearance and bought extra to make pillows and accents. The back of the cabinet is right up against the wall, so it is like have the backing there, you cannot tell the difference and does not move at all. The only time I regretted not putting the Ikea backing on was when we were standing the cabinet up, I would have liked some extra rigidity, but once it was in place and screwed to the other cabinets it was fine. If I only had 1-2 freestanding cabinets I would install the backing to give it a little more support. Next time I would install them just so I did not have to throw them out. (we also sold some). GL!

Thank you so much. Thats our little cutie Bougie haha The lights are from Amazon. Company called Govee, really like their product. It was the 16.4foot lengths we purchased x2. GL with yours!

Thanks! The small ones Ikea sells, the larger ones (1cm) from Amazon! GL!

Thanks I tried to find the originals but only had those! Glad it helped!

Thank you! Room is 11.5' x 7' wide. The large ones on the outside are 100cm, the smaller ones on the inside are 75cm.

Hi. These are all PAX ( For size: The large ones on the outside are 100cm, the smaller ones on the inside are 75cm)

Thanks!

Thank you!

Doors would be awesome! but the space is too narrow for doors, maybe next house !

Thank you!

Thank you so much for the kind words! GL on the house hunt!🤞

It was around 22-3/4" ish but I would recommend you build out one of your cabinets and test fit before securing the base and make adjustments before gluing and screwing. GL!

Thank you! The closet is 11.5' x 7'

Hi, The large ones are 100cm, the smaller ones are 75cm.

Thank you! Bought the pipe with a sleeve already on it but most big box stores will sell drain sleeves separately. Thanks and GL!

@@xacresestate any idea where to get that corrugated pipe from at a decent cost? I'm only going to make a couple of those things but the least amount of pipe I can buy is 80 feet! That's over a hundred bucks. I only need any 8 feet's worth. Any ideas. Thanks

Try facebook market place,@@slamdunk58

Ty! 8 foot 3 inches to the top of the crown, the room itself has 9 foot ceilings.

Hiya, we used the flappy backing to get the fabric measurements. Standard fabric roll for us was 58" from our local fabric shop, just measured the height on the cabinet and added a couple inches for good measure and off cuts. we bought WAY more than we needed but can use them on pillows or something lol GL!

Thank you! The fabric store we have here locally has a standard width for fabric rolls, our roll was 58" wide and we knew we had the 8' cabinets so we bought enough to cover the full length +/- a couple inches.( times 8 cabinets). You can still install the backing if you want after the fabric, one thing we didnt try was gluing the fabric to the backing but that might work as well. I secured the cabinets to the side walls and on top of the cabinets to the walls, didnt use ikea's metal brackets to secure to the wall inside the cabinet.. if it was 1 or 2 free standing cabinets it might have, but 4 screwed together wasn't going anywhere, although I did secure it to the walls above the cabinets for good measure. Best of luck with yours, Hope it turns out awesome!

Yea I think the fabric might be more sturdy then the original backing from ikea lol. Once they were screwed together it was solid. I didn't show it in the video but was also glued and screwed to the side and back walls from top. Can see some of it in the LED video. Thanks

Yes, it will take alittle longer to dry but not much

@@noahgarrett9555 ok thx bro

Hi, It was actually upcycled and refinished, wasnt purchased new!

Thank you! I have another video on the channel about it =]

Thank you so much for the kind words! Would love to see yours when finished! Im sure it will turn out awesome!

Thank you so much! She designed it all 🙂. I just got to play with my tools.🙃

Yes! I agree, someone mentioned that and looking back I would've loved to route in a channel for the LED's to sit in and use LED diffuser cover. Thank you!

Haha. Sure, no problem! 🤣😂 Thank you for the kind words. GL on yours!

Thanks so much!

Hi, You can always send me an email and I can answer any questions you may have, I would say at minimum you need to own / be comfortable with a drill, miter saw & nail gun! You can do it!

how many inches was the closet was it 29 inches or 39 ? ans the depth was 22 inches ? please give me your email to reach out