Very helpful video, I will attempt to do my leather seat in my Mercedes….

Does it have to be HUSKY ?😅

Blaaaa bllllaaaa blllaaaa

In almost 40 years of motorcycling this is the first time I've heard of Surging, I had to leave this and go away and Google it. This type of engine is probably designed to keep pulsing so it's less likely for inexperienced riders to stall. I would consult with Rotax before changing anything.

What should I do if it doesn’t fit properly. My car where the old radio was is curved so doesn’t fit properly so it’s loose how can I lock it into place

Hello can one charge the battery of the F650 CS also while the battery is in the bike or should one charge it indoor where it is more dry and with warm temperature?

Can't one say "Just hold it for 4 seconds" instead of 2 seconds to be on the safe side?

Does this radio have video input? I wanted to do something crazy like use it as a monitor

can you share a link for the trim?

Mine had that hose open too. I just thought it was an overflow or somthing and was supposed to be left open. What did u plug it with?

Thank you for a really clear and comprehensive guide. Excellent! I intend to follow it when I service my forks this winter. Did you consider fitting fork gaiters/rubber bellows, the type that used to be seen on most motorcycles until 1970's and fashions changed. They are still used on motocross bikes and really do prevent dirt and grime from damaging the stanchions and the seals. I bought a set on Aliexpress for just a few £'s/$'s and shall be fitting them during stripdown and hopefully will not need to touch the forks again!

"I watched a couple KZbin videos and I'm an expert now". Classic! I would suggest, however, that for this particular repair, the double needle blind stitch is more effective, a bit stronger, and a bit more forgiving. I used to do this repair the same way you did, and after learning the double blind method, I haven't used a ladder stitch since. Check it out and add it to your repertoire. Great video!

Nice find! This would be my next upgrade from the earlier flip-based 1-din android. Yes, its a smaller screen and lower resolution compared to the flip 1 din, but looks kinda neat. About the touch based volume control, I think there are those 2 wires that a labelled as KEY1, KEY2 and extra GND. You can kinda use that for volume control (you can find these if you got steering wheel control for the car). There are some tricks that I tried, just touching those wires can trigger the volume up and down.

Why did you change your mind too loud ? Power .

Thank you!!! Got it done in an hour.... great video

Hi, Thanks for sharing this video, but what's the model of this exhaust?

Did you make a video on the more permanent fix (or can you link a video that shows how)? I think I'm in a similar situation as you are/were, i haven't checked the date on my headlights yet.

테이프만으로 고정이 잘 되나요?

Thanks for you detailed explanations that helped me a lot. I have a concern about the 3rd bolt of the central bracket, binding the shock absorber (at 7:35 in your video). When I unscrewed it (16 mm flange screw on the right side and 14 mm nyl-stop nut on the opposite side). When I removed the bolt, a washer fell out without me knowing where exactly it was. Temporarily, I put the washer back on the nut side. Could you confirm me where the washer should be on that 3rd bolt, please ?

Great video bro. I wonder if there is any difference in the oil filter and screws dimension for the 2001. :) Got my like. Cheers.

My friend, as a longtime BMW owner if BMW recommends something I do it. They have thought this through.

Great video. Thanks

Hello. No need for any plug adapters ? All lines go in the same place ?

Who makes that oil filter?I just acquired a 96 850r and am trying to figure it out.thanks.

Good video, my rear drivers side window regulator just broke with the window in the down position on my 2001 E39, just after I replaced my front window regulator and I lowered all the windows to spray the rubber channels with silicon lube. I ordered a URO window regulator from RockAuto that is an improved design with roller bearings on the pulleys.

Can you shut the screen off?

As far as I’m aware you don’t need to take off that trim piece on the tail gate

For the record, that bushing was smoked. Replace it if it looks like that next time.

I just bought one with a fried battery. The bike jump started and ran but when I switched it off there wasn't even power to light the dash lamps. I will test stator and regulator output before fitting a new battery. The battery got roasting hot when on a trickle charger. Update: used a voltmeter to test stator and readings were correct so I installed a Battery, not the recommended one, but a smaller size Fireblade one, that can be taken out and put in without stripping half the bodywork, and it's been great, no battery overheating issues. This is the correct starting procedure that Hackjobrepairs is showing us.

Thanks legend how is the old supercharged beast hooe the familys well

So what is the Harbor Freight puller part number?

Where’d you get the lci replacement lights ?

Where did you buy this tool? Cant find it on the interweb

Does it have phone screen mirroring?

it looks terrible

You've got to fold the pins of the radioframe. And with that short radio there is plenty of space by the way. 😂

Just the video I needed thanks !!!!!! ✌🏻🔥👌🏻 I'll go get me one 😊

Dude You are the only other person I have seen with the same tobacco interior as mine. Mine was not loved by it's previous owner. I also have the 3rd row. What are those two computerish things in the left side access panel. I don't have those but the harness is there and they are cut at the end,

Good vid! Txs!

Is it ok to cut the foam off of the passengers side ccv port? It’s the only way to get to replace the diaphragm

Crack. Thanks

YOU LITERALLY SAVED MY LIFE THANK YOU SO MUCHHH

Are those taillights from a certain year or model?

The question is: why?

Did you need to code anything or was it a simple plug and play ?

Can u please publish how to detect power pack at fault

Thanks for the vid. I too prefer the stock’s sound and appearance. On my ‘05 the hanger bolt is a T45 torx. Ride in good health Friend!

Fake!

Well…you tried

Well I feel a little better now. I have been struggling with the bottom bolt for several hours and have ended up where you guys are except I only have 3\8 drive and only have enough extentions to make it into the wheel well. Guess I'm gonna have to get more extensions to get me in the clear so I can put more leverage on it. I came to research on it thinking maybe the bolt was reverse threaded but just need the hulk to bust it loose. Thx for the insight.