Bosch charger AL 1860 CV repair
2:29
Repairing Hilti charger C 4/36-350
13:26
Пікірлер
@MsIwan70
@MsIwan70 4 күн бұрын
super!!! You helped me with the repair of the charger and it's good that you filmed the video in detail, I managed to see the resistance rating, it burned out completely. Thank you so much!!!
@alamgiramirbaig
@alamgiramirbaig 12 күн бұрын
Brother can you confirm this once again. To convert 120v to220v we just need to replace that capacitor?
@apsubmittedtoGod
@apsubmittedtoGod 11 күн бұрын
@@alamgiramirbaig capacitor and remove any varistor MOV if there is one parallel in the input 230v circuit
@Franklinfernandomuñozarancibia
@Franklinfernandomuñozarancibia 19 күн бұрын
Como poder quitarle el bloqueo al te70
@Thwa_yyib
@Thwa_yyib 21 күн бұрын
what is the output voltage of auxiliary power supply 5v or 3.3 0r 12v?
@apsubmittedtoGod
@apsubmittedtoGod 20 күн бұрын
@@Thwa_yyib check this video kzbin.info/www/bejne/a526n32er5uDd7csi=Hsewr2Qx0hzzbGhC
@Thwa_yyib
@Thwa_yyib 21 күн бұрын
good
@artineogda
@artineogda Ай бұрын
You are talking too much :/
@nadeemabbasadnan1681
@nadeemabbasadnan1681 Ай бұрын
Waiting for your message
@nadeemabbasadnan1681
@nadeemabbasadnan1681 Ай бұрын
Hi plz tell me output DC voltage without changing?al1820cv My charger output voltage without changing 33v and 3 battery dead after charging
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
it's 8.5v not charging
@carlosrmaureiraa
@carlosrmaureiraa Ай бұрын
Que se supone que falla tiene el cargador,y porque le pones calor? Bueno creo que es calor. No dices nada. !!!
@carlosrmaureiraa
@carlosrmaureiraa Ай бұрын
Que
@angelemilianagonzalez7387
@angelemilianagonzalez7387 Ай бұрын
dónde eres
@ksklee74
@ksklee74 Ай бұрын
Hey hw r u i have c4/60 l6599 ic burning then i m cjanging but its start up charcing only 3 seç how i repair it
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
i don't know, but you have to check the battery as well, as it behaves like that when it is faulty
@ksklee74
@ksklee74 Ай бұрын
@@apsubmittedtoGod isolved the problem tnk u btu triac is faulty 1and 3 pin is shorted is fix it now charger is working now
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
@@ksklee74 👍
@danman132x
@danman132x Ай бұрын
I wish Dewalt made these 120-220 universal. I live in the states, but when I move to germany i want to take all my chargers with me. Might have to do these mods on them all.
@SokeElektronikKartTamiri
@SokeElektronikKartTamiri Ай бұрын
@istvanszilagyi5773
@istvanszilagyi5773 Ай бұрын
Az enyémnek nincs hangja mi lehet a baj?
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
does it charge the battery?
@istvanszilagyi5773
@istvanszilagyi5773 Ай бұрын
@@apsubmittedtoGod Igen tölti
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
@@istvanszilagyi5773 check buzzer, the round component marked with 2202, at minute 18:05
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
@@istvanszilagyi5773 or try this kzbin.info/www/bejne/hYO8eHaKarSWZqM
@istvanszilagyi5773
@istvanszilagyi5773 Ай бұрын
@@apsubmittedtoGod igen
@GaffarRangrez
@GaffarRangrez Ай бұрын
dear sir.. will it work for TE 1000-AVR hilti
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
no, just te 76 old model
@hiltitamirbakmservisi4328
@hiltitamirbakmservisi4328 Ай бұрын
Thank you, grandmaster, thanks to you, I learned one more thing. God help you
@user-ju3et8gg5j
@user-ju3et8gg5j Ай бұрын
Its can work with 220v outlet?
@apsubmittedtoGod
@apsubmittedtoGod Ай бұрын
@@user-ju3et8gg5j yes
@misakostic72
@misakostic72 2 ай бұрын
Thank you. This was exactly the problem with my charger.
@عبدالحكيمالعجي-ت4غ
@عبدالحكيمالعجي-ت4غ 2 ай бұрын
ترجمه لغه عربيه
@kamalgermanya3423
@kamalgermanya3423 2 ай бұрын
Thank you for your wonderful effort, regards❤❤❤
@eugenenechaev5735
@eugenenechaev5735 2 ай бұрын
Very interesting, but nothing is clear
@정규식-r4w
@정규식-r4w 2 ай бұрын
Thanks for the information. You just change the capacitor (400v available) and it works right? I don't understand why Dewalt make it with your method, you converted it to free-volt.
@apsubmittedtoGod
@apsubmittedtoGod 2 ай бұрын
Making it free volt will make it not very efficient, as for lower voltage it requires a bigger capacitor and taking so twice the space, it is just one capacitor to be changed and you either have it 230 or 120v. In this case it works with 230v but also less effectively with half the power in 120v
@EdMeuwissen
@EdMeuwissen 2 ай бұрын
Thank you very much, it worked out perfectly. Now my machine is running again!!
@EdMeuwissen
@EdMeuwissen 2 ай бұрын
Thank you very much, it worked perfectly. Now my machine is running again!
@mujahid-salim
@mujahid-salim 3 ай бұрын
i need some help
@apsubmittedtoGod
@apsubmittedtoGod 2 ай бұрын
@@mujahid-salim hello, how can i help you?
@mujahid-salim
@mujahid-salim 3 ай бұрын
hi brother
@orinokoflow6280
@orinokoflow6280 3 ай бұрын
I received Hilti PR35 rotating laser delivered buy courrier. It was in working order before. It refuses to turn on, the battery is 100% working. What could be the possible cause of malfunction? It might have been shaken in it's original box while on the road, though it was packed. Thanks 🙏
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
@@orinokoflow6280 i dont know, it can be anything, you have to check all the way in of the power from the battery, but the thing with the power button is a common problem for Hilti, the flexible conmectors sometimes disconnect in the middle.
@Travieso2282
@Travieso2282 3 ай бұрын
Hi my battery works and the light comes on but my battery won’t charger when I plug it in
@patrickjoachim
@patrickjoachim 3 ай бұрын
Great video! Thanks! On mine, the MOSFET in the corner of the card has blown, I can't read the reference. Can you tell me? And also the reference of the 4 diodes? Thanking you in advance.
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
P6NK90Z, but you can use higher amperage, i usually put P10NK90z
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
diodes 1N4007
@patrickjoachim
@patrickjoachim 3 ай бұрын
@@apsubmittedtoGod Many thanks !👍
@JoaovianeiDias
@JoaovianeiDias 3 ай бұрын
Onde encontrar o esquema eletrônico da placa Al 1860 do carregador de bateria Bosch
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
just google AL 1860 schematic and select images, someone has posted it
@noeltech2020
@noeltech2020 3 ай бұрын
Sa nakapanood neto nice tutorial
@cassidax5
@cassidax5 3 ай бұрын
Hilti tools are trickier than most to work on, especially the electronics. Thanks for taking the time to post these!
@cassidax5
@cassidax5 3 ай бұрын
Thanks for your content I really appreciate your videos as I’m always working on equipment. Can you give me an email address that I can’t contact you about a Hilti DD250 I’m having problems with? Thanks again
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
what is the problem with DD250?
@shotiko1001
@shotiko1001 3 ай бұрын
I have a new model DCB-107.The motherboard number is pcb4445-rev 0.6 2020-04-01.If you can convert it from 110 to 220V, maybe you can record a video
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
just change the big capacitor to 400-450volts and with half uF value, and remove any varistor that is in parallel before the bridge rectifier
@Meow-meow421
@Meow-meow421 12 күн бұрын
Half uF value of the 200v old capacitor?
@gonzalolucero392
@gonzalolucero392 3 ай бұрын
Hello, if the transistor doesn't work, just by changing it would it be fine?
@apsubmittedtoGod
@apsubmittedtoGod 3 ай бұрын
You also have to check nearby resistors and diodes, because when a transistor gets shorted in gate pin, it may damage components or even the IC,
@MihaiAlexandruPreda
@MihaiAlexandruPreda 4 ай бұрын
Does this works on te 70 atc?
@apsubmittedtoGod
@apsubmittedtoGod 4 ай бұрын
@@MihaiAlexandruPreda no, it works just for TE76 old model
@MihaiAlexandruPreda
@MihaiAlexandruPreda 4 ай бұрын
@@apsubmittedtoGod thank you.
@alhamdelectricandarmaturew2997
@alhamdelectricandarmaturew2997 4 ай бұрын
Hello brother i m from pakistan I want to discuss something with you can i get Your WhatsApp contact ❤
@tomandjerry9428
@tomandjerry9428 4 ай бұрын
Can you convert makita DC18RC 120v to 230v.?
@apsubmittedtoGod
@apsubmittedtoGod 4 ай бұрын
kzbin.info/www/bejne/rIjGg3SQpseoodk Replace the capacitor from 220v to 400-450v, and remove the varistor, the yellow component
@powertoolsrepair
@powertoolsrepair 4 ай бұрын
Very good video, helped to me alot. Thank you
@bierposse
@bierposse 4 ай бұрын
wat is de waarde van de weerstand what is the value of the resistor
@apsubmittedtoGod
@apsubmittedtoGod 4 ай бұрын
180k ohm
@HardcoreHokage
@HardcoreHokage 5 ай бұрын
Which God and which holy book?
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@HardcoreHokage the Creator and Owner of everything, the Book of good moral values. God bless you.
@HardcoreHokage
@HardcoreHokage 5 ай бұрын
@@apsubmittedtoGod ah your talking about Zeus. Where can I get a copy of Zeus' holy book?
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@HardcoreHokage zeus was the son of cronus, he wasnt the creator of the universe
@HardcoreHokage
@HardcoreHokage 5 ай бұрын
@@apsubmittedtoGod No it was Uranus who created the Universe. Zeus bless you.
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@HardcoreHokage uranus still had parents, so not the God the Creator and Owner of everything
@uncanalmas5824
@uncanalmas5824 5 ай бұрын
Did you place any additional resistors on the side of the capacitor? Since I see that other boards of the DCB1104 model do not have those resistors.
@uncanalmas5824
@uncanalmas5824 5 ай бұрын
Exactly the D3 and R7
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@uncanalmas5824 no, i didn't, D3, R7 and the capacitor there are snubber circuit to block voltage spikes coming from transformer, 1:43
@alamgiramirbaig
@alamgiramirbaig 12 күн бұрын
Thanks for your helpful video ​@@apsubmittedtoGod
@alamgiramirbaig
@alamgiramirbaig 12 күн бұрын
All I need to replace that capacitor?❤
@carlosreyes-ko9im
@carlosreyes-ko9im 5 ай бұрын
Hello. Sorry. I have the same charger. The IC 3113 is ok but does not appear 5 volts. Also oscilator circuit IC P1216 was replaced but the charger does not work. I think first I should have stand by en then the main voltaje but I do not find the problem. Thanks for your answer.
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
do the LEDs turn on when you plug it in?
@carlosreyes-ko9im
@carlosreyes-ko9im 5 ай бұрын
@@apsubmittedtoGod no. Nothing happend. Only appear 165 VDC in the mains capacitors.
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@carlosreyes-ko9im so the problem is in the snubber circuit, is it the same exact charger as this in the video?
@carlosreyes-ko9im
@carlosreyes-ko9im 5 ай бұрын
@@apsubmittedtoGod HI thanks for answer. Modelo charger is DC18RA
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@carlosreyes-ko9im did you find any faulty component there?
@logosrema7105
@logosrema7105 5 ай бұрын
Твое видео помогло бы если я не нашел номиналы компонентов ранее вдругом месте ,хорошее дело делаешь. Слава Спасителю Иисусу
@uncanalmas5824
@uncanalmas5824 5 ай бұрын
Thank you for your valuable contribution, how long has the charger been working for you?
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
these chargers after conversion work fine, no problems with that
@josephshantimba8124
@josephshantimba8124 5 ай бұрын
Amen
@alexlazaro6913
@alexlazaro6913 5 ай бұрын
Hola puedo hacer lo mismo con un TE 70 q tiene la misma alarma y no enciende??
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
no, it works only with this tool TE76P ATC
@user-2uf2kr2c
@user-2uf2kr2c 5 ай бұрын
Hello, mine is blinking red/green but not charging batteries. what could that be? I have 2 with that problem, a DC18RC and a DC18SD. Regards
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
are you sure the batteries are ok?, if yes, then check the mosfet, the big capacitor, and small capacitor near the driving IC
@user-2uf2kr2c
@user-2uf2kr2c 5 ай бұрын
@@apsubmittedtoGod Ok. Thx. Picture of the driving IC? Regards
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
@@user-2uf2kr2c 13:13 IC1 the one with 8 pins, and capacitor C12
@user-2uf2kr2c
@user-2uf2kr2c 5 ай бұрын
@@apsubmittedtoGod Ok thx. Godbless
@carlosreyes-ko9im
@carlosreyes-ko9im 5 ай бұрын
Hello. Mine stand by voltaje. K3113 is ok, but dont have 5 volts. Do you know what cold be?
@maxfoundationrepair
@maxfoundationrepair 5 ай бұрын
How to reset a Hilti TE 3000 avr ??
@apsubmittedtoGod
@apsubmittedtoGod 5 ай бұрын
you need SRT service reset tool, to do that