Not worth it unless going turbo as well...just my opinion ! .i can put a turbo 0n my sohc & blow your doors off....😂.cheers

Fuck yeah

To bad you wrecked this rig. Ever get another one!?

Bearing juice haha

Good tips thank you for sharing this important information

Poor lathe 😓

Poor headstock bearings. Circa $2000 for my Colchester

How did you get the computer to recognize the switch

I like how he's like, "Weld complete! Video over!" Where's the result testing? 😭 How good was the weld?

I have a feeling theres alot more pressure involved in actual friction welding

Can we use DC motors for Friction welding

Not as easy as they make it look! Ha ha. Not even a lathe can do it!

Very clunky

Jesus the dude’s got a greasy rag sitting like 6 inches from the chuck in one segment. Talk about flirting with danger.

Cool music too! scOtl@nd!

Mine was a pita to get back in lol😭😂

Soo cool great job

Good job, try heating up the welding surfaces with a cutting torch, should work better, since a lathe is not designed for friction welding.

Nice welding machine ;)

3:39

you would have better luck not using 90 degree angle 85 or 80 would have worked better

This was a while ago but I recently made one of these that runs smoothly and fast and if you were to make one again it seems that the timing of when the valve opens is slightly off. And the exhaust or where the air comes into the cylinder isn't mandatory. But I enjoyed this engine. Good work!

Just buy a 2 stroke gasoline engine it will work much faster, noisier, stronger and durabler

2 stroke engines of lego wont run

You just wanted to see all those sparks Jireh. This is Jaye btw.

Oh I feel bad for that tail stock!

Holding with tailstock not so good cus tailstock have play, also it need a good forse in order for metal to metal bond, easy 1or 2 tons of force on big pcs.

If you had heated up the metals before you tryed this would help you get the bonding you was wishing for

Holy lack of safety... wrenches left on machine, long loose fitting sleeves, my guess is the oil has a low flash point and will light up real easily.

If that's oil for coolant and it looked like oil good luck, it's everywhere and u have bright hot metal next to it you're going to burn the shop down

Hey Jireh it's Tyler. This video showed up in my recommended videos. The internet is a small place, huh.

Este último es un pelotudo terrible. quien lo metió en KZbin

That's some serious heat transfer on the jaws isn't it? Isn't there a concern of damaging them ?

What is the coolant used motor oil?

Gay welding for dummies. Sorry.

What an idiot, it's becoming more difficult to watch. Wow, good luck fool.

faster is always better when friction welding

did you crack the tailstock quill?

nice video.

Frayed sleeves while working on a lathe? Please don't wear sleeves on a lathe if you want to keep your arms.

You rock!!!

/sensible_chuckle

Do you have to replace the ECM if you swap a SOHC for a DOHC on a saturn sl1?

Awesome! Was it worth it? Notice the difference? I have a dohc 99 to put in my 02 sc1 but im pretty nervous. I dont wanna fuck anything up

Great video! What year is this? I'm going to try it with my manual 1999 Saturn SL1, swapping out the engine with one from a manual 1999 Saturn SL2, do you think it will work? Will it be a swap and go?

im planning on doing this same swap for my 1994 sl1 manual tranny and I was wondering what was the total cost of this? were many modifications needed?

I got a 1997 sohc manuel would i still need the gauges form a dohc ? And is it really that simple to take the old one out and put a new one in ??

is it a swap and go??? or is there any mods needed? bellhousing and wiring harnesses

I used a crank. It was very hard to get the timing of both valves.