Good Morning! Can you Help I have the same Issue I took the car to bmw they chargme 350$ and they couldn’t found the problem I need help 🙏🏻

I think I have similar issue. I just bought a mk2 octavia (2.0TDI) with ECU problem. It cranks but not firing up. I'll check the switched ground to the engine control relays tomorrow. I also can't hear the fuel pump working at all. Diagnostic cable is also not able to communicate to ECU but it can to other electronics.

Repunerea pe paduri imi i-a ora

Cat de usor pare cand ma uit si cat de multi timp imi i-a sa pun un integrat pe paduri si sa nu se miste

Ce imi place sa dezlipesc integratele de genul cu repunerea pe paduri si lipitul e mai greu

I’m confused. So, the “easy way to replace a capacitor” … is to replace the capacitor the hard way with braid/wick? Come on now!

Can explain what kind of product name...

Dziękujemy.

Queria ver funcionando

Hi thanks for video. I took module off. Is it safe craginng it without module? Can you pls share video how safely charge battery without module? Thanks

Hi Alex. How can i connect u? Via website and mentioned emails is not possble

Thats the first time Ive ever seen bonded leads used in an ECU and the first time Ive seen them repaired. I would love to know if the repair actually worked, why did they break in the first place? I assume you are using high Silver content solder or those silver pads on the thick film circuit will get absorbed?

Could you provide the part number/specs for that transistor? I have the exact symptoms as you and I want to replace the faulty transistor on my board.

Thanks brother

Hello waht use to remove Gel

Hi very nice video Do you repair the Sams?

Can you please write your WhatsApp contact number to my friend?

Hello fred havareyou

Can you please write your WhatsApp contact number to my friend?

Can you please write your WhatsApp contact number to my friend?

Hi

These damn safc161cs32 like to die and short 5v rail to gnd, easy to check idle consumption by connecting only gnd and +30 there should be no amp draw. Shorted mcu usually consume 0.7A and draining battery overnight, also shorted keyless mosfets will drain battery. Bad thing is we can´t clone this mcu, I personally have not found programmer that can read this mcu.

Amtech is the best flux. Nice soldering there.

Well done brother u are a genius can u explain more precisely how to read pcb map to trace the track to the shorted component on the board

do i need to connect to powet supply before test?

I have some questions about range rover Evoque instrument cluster.. how can i contact u

Hey friend, what was the issue at this device? Where did you buy the µC? Best!

Which software using for read and write

How Do I contact you so I can send mine I have the same issue burnt ic chip. Also How much will it cost me

This video is very helpful

This was exactly what I needed to see. I’m trying to replace a m92 chip in a Nintendo switch but one of the traces is gone. So I’ll need to do this and then connect it to a capacitor.

Hello , I would need some help with my head unit Ntg5*1. Please can I have your contact details ?

Hello, excelent! Is it possible to inform the wiring for powering up the radio without the car wires, like testing at home ? Thanks.

😮 Impressive !! Great video, so, you re saying that if you replace the unit whit another one, it won’t work?

Dear how are you ? what are your A23E smd because I need repair but not have datasheet . thank you very much

HI. What kind of tool is used to remove varnish from the board track?

Ciao mi puoi aiutare a capire come fai a rimuovere il gel protettivo dalla tcu dq200 grazie mille

What’s the best email to write to you as I’ve tried the web site and they don’t seem to work Re - Kessy repair vw Touareg

That MCU is not locked, i found the pinouts on IO TERMINAL or VvDi pinouts out under the board no need to seprate thd board, used my Autel im608 and read the mcu and Eeprom saved it and cloned a new bcm

Goood job!!

Thank you for saving my time! I had the same, shorted diode problem in EDC17C08.

Amazing soldering skill

Im really surprised you can get a replacement chip

Hello, i have also what i think a relay related problem, when i connect the cable that is under the to the module i hear three clicks, try to engage the handbrake but no sound from the relay or motor. maybe a bad relay? It also has a small defect on it, peolpe say that is a sign of a bad relay. Thanks

Dont zoom-ing so much, because it scares the bit😜

Would've been a good video if u would have let us know what the hell u actually put on it in the beginning. 🧐🤔,🤨🤦‍♂️🤷‍♂️

BTW, why you don't show the measurements on the video?

not sure I understand the logic of this troubleshooting: first you measure 23 ohms - which is not a short, then decide to desolder a big mosfet, without any reason whatsoever, then replace it , even you say it is good. By this logic "troubleshooting" means replacing every component you think may be faulty

your audio is terrible