I also have a 4runner the same year and I would like to let the public know just because you purchased the front control arm your lift is still incomplete. With bigger springs in the rear and stock rear control arms with stock track bar it sucks the tires towards the rear door and changes your wheel base and pinion angle. So with the same kit shown in the video you still need a front diff drop sway bar drop and adjustable rear arms along with adjustable track bar or bracket for track bar and measure your wheel base before you lift it and measure you pinion angle and try to match the best you can to save your ride quality and wear on components...and curb appeal,I find it funny when I see the back tires looking like the truck trying to poop 💩 haha 🤣🤣 all love great video just passing the information

Thanks bro!

Wondered if it’s worth running a weld along the cut lines once you’ve done the bends?

What a legend. My 4Runner will be even more of a beast in no time

Can u install seats on my 69 nova as well I got the seats and bracket already

Do you have the part number for the 5100 front and rear?

Was this a 3in lift or 2in?

Blahblahblahblah

Interesting that we all have came to the same conclusion/method for our gloves, which for me is hot 5 gallon buck of water with palmolive oxy/dawn or even better is simple green, but its more expensive since it takes like a 50/50 mix. So far what ive had the most success with is hot water/dish soap and juuuust the right amount of bleach. Too much and itll ruin the rubbery part by making it hard and not pliable.

How does it work if it is outside of the engine bay?

But how do you take the paint off the plastic cap that was chrome

I don’t wash any more pairs than one, and you can probably do all your gloves in the bucket. Start again. Except use hot water and dish soap and squeeze the gloves inside the water before leaving them inside the bucket overnight. The chemical soap water still breaks apart leftover grime on your gloves, and the heat just makes it easier. Take the gloves after leaving them overnight and let them sit to air dry. You might as well use them wet, but that’s as good as you can get them back to normal.

what oven cleaner u got ? the one in ur description i’ve bought at stores and it’s never enough foam and it always jams 🤦🏽‍♂️

What spring you use for front? Stock, or med weight?

anti lag flamethrower added

that wheel diagram adjust said alot what another hasn't and purely though purely joyous to see it notwhat it once in location where it wouldn't

that is a hydraulic skid plate ; pizza puff CORRECT

skid slicker not my realm see that

no way ; funnels tooth

don't matter you have

glide slight no upset

launch pad man no logitech why would you assume gls aesthetic on polar temp

For a second there I thought you were about to hit that car lol

Never use a glove while using a grinder but should use a face shield

Hi, i Have question about the rear part, I'm thinking getting bilstein 5100 for my 4th gen 4runner but can I using OEM spring and will it compatible with this longer body struts? Thanks

Wow thanks

Easy for him to say. Most of us do NOT have our motors OUT of our vehicle, when doing this kind of maintenance 😆 But thanks for info 👍

I cleaned mine by blocking it off and throwing the iacv in a 30 gallon trash can

they are designed so that the rear is 1.5 inches higher than the front

I’ve got the x-reas on my 2004 4runnner. Just replaced it with a costly complicated system Replaced with Billstein 4600 all around

I'm gonna try to reuse old plates off a different truck. I'll get itcto work

Way late but I'm looking at doing this for my avant. The skid plate on ECS is like $300 lol

You had me at drift !!!

California sucks! Impressive work and video though! Sick s14 btw 😎🤙🏼

Still have car?

hows the alignment ? did you need and upper control arm for the front?

can i use this method on a spraiypainted car without damaging the the rubber or plastic?

I put sound damping material in the floor boards and door panels of my Nova. But man, it is so damn loud in that car!!

You are too fast for me

I forgot another question so these are good shocks to do for me I really don't do off routine but I love my forerunner and the suspicion needs to be deleted and replaced

I have 2008 forerunner and I wanna replace the X-ray as delete it and put on new shocks front back now I'm hearing if you lift it too high you could damage the U joints from the front drive system out of the transfer case is that true I will not set it that high I'll keep it on the low setting Was your ride height set to specs will it will not mess up the OEM drive train🤔🤷

how much was this lift?

Wow what a day. I bet y’all were freezing cold when you had to put the spring back in.

You’re a real one!

That is exactly what I was looking for... thanks for the demo!

Would the oven cleaner eventually take the chrome plating off if you kept cleaning it, or cleaned it too much?

Do you have to take the rims off of the car, or can you do them while they are on the car.

engagement

Much appreciated!!

Nice job!! I just brought a 2004 4runner with a set of Bilstein 5100 on front and rear. I would like to change the rear air bag suspension to spring in the further, do you have any suggested spring?