Herbie Amey

Пікірлер

@G2GE 21 күн бұрын

Did you go back and weld up the engine mount you cut to clear the exhaust?

@Blacksheepcustom 21 күн бұрын

To be honest I did not. It’s still on the road to this day and not a single issue.

@logan1274 25 күн бұрын

Has it caught on fire yet?

@Blacksheepcustom 25 күн бұрын

@@logan1274 hahaha the battery? Not its great works as it should!!

@RobertMarttila Ай бұрын

How long was it sitting for?

@RobertMarttila Ай бұрын

How long was it sitting for? I think the same thing happened to me.

@Blacksheepcustom Ай бұрын

@@RobertMarttila so I bought it off market place. The lady said it was a good year or so.

@mr.certifiedboss418 Ай бұрын

Sounds good 👍🏾

@Blacksheepcustom Ай бұрын

@@mr.certifiedboss418 thank you!!!

@shannonlove1981 2 ай бұрын

sweet build! what booster is that and and air intake

@Blacksheepcustom 2 ай бұрын

@@shannonlove1981 booster is a eBay one and intake is from “swap time”

@shannonlove1981 2 ай бұрын

@@Blacksheepcustom what i thought on the intake. i’m actually doing an 86 k10 . how did you do full setup

@Blacksheepcustom 2 ай бұрын

@@shannonlove1981 just search on eBay “c10 booster” and a bunch show up. There is a chrome one and black one. Black was like 100$ more tho.

@shannonlove1981 2 ай бұрын

i meant fuel! sorry

@Blacksheepcustom 2 ай бұрын

@@shannonlove1981 what do you mean by full set up?

@justinpeacock2937 8 ай бұрын

What adapter did you use have a part number? Was it sold as a kit or did it come with a shaft or anything??

@Blacksheepcustom 8 ай бұрын

I bought the adaptor from advanced adaptor. When I got it, that’s when I noticed the turbo 400 to np205 adaptor was almost exactly the same thing as what I just bought.

@justinpeacock2937 8 ай бұрын

@@Blacksheepcustom so did you have to put in a vss ring in the 205? I’m looking at 32 spline that came off sm465 transmission and I think all I need is that adapter but I see they sale it all in a kit. I don’t need anything extra other than the mount

@Blacksheepcustom 8 ай бұрын

@@justinpeacock2937 I sent the tail housing to them and they did the work for the vss

@justinpeacock2937 8 ай бұрын

@@Blacksheepcustom so the adapter from AA was just sent to you by it self nothing else with it?

@Blacksheepcustom 8 ай бұрын

@@justinpeacock2937 yea was their adaptor. A gasket and seal. Then I sent them the tail housing to get machined for vss

@dalemaloney5803 10 ай бұрын

Wasn't a good spot on the back side? Less visible and closer

@Blacksheepcustom 10 ай бұрын

Hey dale. I guess I could have but I moved the motor as close to the fire wall as I could so when the kinks are all worked out it’s going to be getting twins or a big single. So I was just planning for as much room as possible. Going to make a quick follow up video of it all mounted up now.

@crackbaby5213 10 ай бұрын

Here come the keyboard mechanics, prepare to explain 500,000 times that you picked up the wrong fitting

@Blacksheepcustom 10 ай бұрын

Haha all good. I’m very green to all this so I’m always down for a laugh and some pointers!

@BBQandStreetCars 10 ай бұрын

Way too much slop in that hole. Something ain't right

@Blacksheepcustom 10 ай бұрын

Grabbed the wrong barb fitting. I can promise ya she’s tight

@heffedirte6243 10 ай бұрын

That's a little bit loose bud

@Blacksheepcustom 10 ай бұрын

Grabbed the wrong fitting. She’s tight

@farmkid7888 11 ай бұрын

The 400 adapter won’t fit a 4l80e, it has to be machines to fit. With the cost of labor, you might as well buy the AA unit, lighter and stronger!

@Blacksheepcustom 11 ай бұрын

Did you watch the video? I explained that. You can do the machining with a grinder no problem.

@farmkid7888 11 ай бұрын

@@Blacksheepcustom yes I watched it! You can’t machine down a circle ⭕️ with a grinder. The 400 circle is a larger diameter than the 4l80, has to be done on a lathe.

@Blacksheepcustom 11 ай бұрын

Dude the output shaft is not nearly even close to that size 🤣🤣🤣

@DoggyDogYT 9 ай бұрын

@@Blacksheepcustom Hey boss, question I have a 4L80e 4x4 and want to swap it with my TH400 with a np208, you think that mount will bolt right up with any further milling as you suggested? 4L80e with NP208 using the TH400 mount(like the one in the video).

@Blacksheepcustom 9 ай бұрын

@@DoggyDogYT I’m not to sure. I used the 205. If the 205 and 208 share the same mount then I think it’s safe to say yes. But I honestly don’t know

@epiccarguy892 Жыл бұрын

Euro 0

@recycleman975 Жыл бұрын

🥵

@Smokeroux 2 жыл бұрын

How did you seal up the rear holes above and below the tranny tail shaft?

@Blacksheepcustom 2 жыл бұрын

What do ya mean the rear holes?

@Smokeroux 2 жыл бұрын

There is an open hole above and below the tail shaft barring. Mine is blowing fluid thru the Adaptor and Dana 300

@Smokeroux 2 жыл бұрын

Soapbox94 has a video showing them plugged. My plan to fix if need be

@Blacksheepcustom 2 жыл бұрын

Not sure. I couldn’t find the video your referring to on his page. Sorry

@Smokeroux 2 жыл бұрын

@@Blacksheepcustom kzbin.info/www/bejne/Z3vXgnymZduthLs

@pankero1 2 жыл бұрын

what transmission mount are you using under that adapter?

@Blacksheepcustom 2 жыл бұрын

Running a custom homemade one

@pankero1 2 жыл бұрын

Did you have to shorten the 2wd 4L80e´s output shaft?

@Blacksheepcustom 2 жыл бұрын

I had the 4wheel drive 4l80 with the correct size output shaft. Don’t quote me I believe you can cut the 2wd to length to make it work or remove the 2wd output shaft and use it in the 4wd trans. There’s some pretty good forums in regards to the output shaft and what lengths you’ll need, I can’t remember off the top of my head.

@keithjurena9319 2 жыл бұрын

356 T6 aluminum casting has greater strength than the nodular iron THM400. Improved ductility too. The metal is much more expensive too, cost of casting and machining about the same.

@Blacksheepcustom 2 жыл бұрын

That may be true, but who’s ever heard of a adaptor breaking? So to save a few hundred bucks I would have just made the one I had work. All good tho.

@coltonfreund8302 2 жыл бұрын

Any drive by vids? Or revs? Sounds great

@Blacksheepcustom 2 жыл бұрын

I’ll try to get one in the next few days. Does sound great idling and cruising around town. Just going up hills it’s obnoxious.

@natek4741 3 жыл бұрын

This sounds awesome! Are those magnaflows deep in person? Thanks!

@Blacksheepcustom 3 жыл бұрын

They’re awesome!! But once the Jeep labors up a hill, or a hard pull it’s very loud!!! Almost straight pipe loud.

@natek4741 3 жыл бұрын

@@Blacksheepcustom really?! I wouldn't expect that much volume increase compared to the idle sound! I'm trying to pin down a set of mufflers for my LS c10 and magnaflows are just so deep sounding!

@Blacksheepcustom 3 жыл бұрын

@@natek4741 yea I swear. It hurts my ears in the cab. It’s also a tin Jeep so in the cab of the c10 it may not be that bad. Also there’s a lot more piping so that may deaden the sound some, im not muffler expert lol. The more street friendly black widows are nice! Check those out, im doing a gen v lt swap in my c10 and definitely thinking about a quieter black widow.

@merccrewlcab2385 3 жыл бұрын

Bitchin info! Going to save me some bucks, thanx eh! Did you run driver or passenger side drop? I am going to cut down the output on my2wd 4L80 and go with a driver side 205 for my Chevy G30 van. Cheers!

@Blacksheepcustom 3 жыл бұрын

Thanks man!! I did passenger drop. If you don’t have a adaptor I have the turbo 400 to np205 adaptor just sitting on the shelf. If your interested let me know!

@rodrego5 2 жыл бұрын

@@Blacksheepcustom do you still have that adapter ? Looking to do the same setup.

@Blacksheepcustom 2 жыл бұрын

@@rodrego5 hey man, I do still have it but I think I’m going to hang onto it for a future build.

@SubePelayo928 3 жыл бұрын

4l80e is a 32 spline output. Did you swap out the input on the np205?

@Blacksheepcustom 3 жыл бұрын

I didn’t have to change anything, just got the adapter and it all bolted up

@SubePelayo928 3 жыл бұрын

@@Blacksheepcustom your Np205 had the 32 spline input already then! That’s good! I have the 10 spline input. The case has to get machines to fit the larger bearing on the 32 spline input

@keithjurena9319 2 жыл бұрын

@@SubePelayo928 90mm OD bearing. Easy to machine, once set up. I got lucky, my truck came with a figure 8 pattern, 90mm input bearing OD and long input shaft. Still looking for a good 4x4 4l80e

@milanantonoski673 3 жыл бұрын

Šta je ovo? Kakav mu to sulundar viri iz desnog prednjeg krila.

@jeeperzcreeperzz 4 жыл бұрын

So either would work for a np205 sm465 swapped to np205 to 4l80e?

@Blacksheepcustom 4 жыл бұрын

You going from the sm465 to 4l80e then yes from what I can see one will just require some grinding. Also you will need the vss drilled into the tail housing of the np205 unless your doing a Manuel valve body.