This does not work for the 2003 Kia Sorento EX. Totally different air filter housing and assembly for that model.
@npcasp5279Ай бұрын
Excellent video, the adjustments of the actuator rod catch my attention, how many millimeters higher and lower, thank you
@dawggonevidz9140Ай бұрын
Only two things I really really hate about the Sorento, having to take the wipers and trim under the windscreen off to get at the back of the engine and the fact they put the oil filter above (and behind) a cross member you then have to clean every oil change. I'm thinking I might just cut chunks out of that trim on mine though.
@dirkp6350Ай бұрын
Do you need to pull intake manifold off to get the head off?
@CarlosAlvarado-p5s2 ай бұрын
que torque llevan los tornillos de culata
@DooDicky2 ай бұрын
How much inhg should the arm start moving and how much inhg when it reaches stop screw?
@DooDicky2 ай бұрын
How much turbo pressure in PSI should it be?
@MichalŽilinský2 ай бұрын
Pomohlo mi to video ....👍👍👍👍👍
@paultandy81842 ай бұрын
Hello thanks for this video, Is there some trick to removing engine from bell housing. Everything is unbolted just wont disengage Again thankyou
@mohamadtubless3 ай бұрын
Very good 👍
@robertwhyatt10813 ай бұрын
Hi good video, but it different in the 2004 model as it doesn't have a separate filter.
@npcasp52793 ай бұрын
cual es el torque de apriete de los pernos del turbo, de antemano gracias
@npcasp52793 ай бұрын
Excellent video, consult. How to know if the actuator is faulty, what is the symptom that the car presents, Congratulations from Chile
@alexlex21474 ай бұрын
Thanks !!
@npcasp52794 ай бұрын
Excelente video, consulta. Como saber si el actuador esta con falla cual es el síntoma que presenta el coche, Felicitaciones desde Chile
@enriqueorihuela87174 ай бұрын
Thanks You míster
@DanteMagallanes-mq9jd5 ай бұрын
By Dante magallanes estudent mechanic
@lloydballard70515 ай бұрын
Just had to do this today. Video did not show the most critical part (replacing the outer nut). He did show the removal so replacement was the same. Had trouble getting the inside door handle cover off. Used a pick and had to sand off the scrape. I had trouble getting the two studs of the handle to go into the door. Had to grind the inner hole a bit so the stud would go in without a fight.
@ГалымТауекелов5 ай бұрын
Немой чтоли
@alexroberts45046 ай бұрын
Thankyou ❤
@thesupernad6 ай бұрын
Camera man has had a few too many.
@serdaragdas6 ай бұрын
Bravoooooo
@madcook19367 ай бұрын
Thank you fir this video
@Vlasnijdosvid7 ай бұрын
Доброго здоров'я. Все ж таки, з яким моментом потрібно затягувати зірочки розподільчих валів? Чому у Вас вказано два діапазони крутного моменту?
@josemiguelramoscaceres57537 ай бұрын
Sensores de temperatura cuales son
@MrYourikaam7 ай бұрын
Thanks
@christyinthecarolinas8 ай бұрын
Latex gloves bc the oils from your fingers can cause the bulbs to break or something. At least that's what my dad said 😂
@nidzastevanovic5588 ай бұрын
Decko ti nemas pojma
@abderrazzakhamama15248 ай бұрын
merci pour le partage❤❤❤
@normanpicadocarmona-le2io8 ай бұрын
Los tiempos
@fabiomendes70439 ай бұрын
Very very very good, congratulations from Brazil!!!
@radomolnar11059 ай бұрын
To nevieš kúpiť tesnenia ze všade jebes silikón
@Руслан-ы1м9 ай бұрын
Здравствуйте Подскажите пожалуйста, какая головка используется при разборе головки ? 12 гран 17 или 16 мм ?
@eduardodaquiljr96379 ай бұрын
What if you remove first the radiator before removing the fan?
@OGBasic9 ай бұрын
Absolute legend
@kalmeslex96910 ай бұрын
Do somone know the DT number of this light , because I need to change exactly that whole piece and can t find the exact Modell
@jamessanchez343810 ай бұрын
Thank you Randy, I'm doing this as soon as I can find a place that sells the fuel filter
@eduardodaquiljr963710 ай бұрын
You can use electric socket drive to speed up tightening of bolts
@firdovsiquliyev310811 ай бұрын
Kia sportage avtomabilində benzin mühərriklərdən hansı daha keyfiyyətli və dözümlüdü 2.0 və 2.5 mühərrik bilən varsa bir zəhmət yazardınız.
@northernchap Жыл бұрын
Thanks for this video, here's the translations of the steps in case anyone wants them in English: Blanking of the EGR valve. Step 1 - We remove the car battery Step 2 - Loosen the 2 nuts on the pipe from the EGR valve Step 3 - Loosen 4 bolts so that we have free space to remove the gasket from the pipe on the turbo side Step 4 - We put the blanking plate in place of the original gasket and screw it together lightly Step 5 - Tighten the 4 bolts of the EGR valve Step 6 - Tighten the 2 nuts on the EGR valve pipe Step 7 - We mount the battery back and it's done I know it's quite simple to follow but just in case this helps someone.
@AndresluisBaes Жыл бұрын
Lo malo no se vio al colocar nuevo
@WalterCassano-j2m Жыл бұрын
Please, how to change antenna with a fix one
@lourdessoberano2666 Жыл бұрын
why just silent no talk no explaination like step by step 1..2..3..
@HAMRADIOJOE4178 Жыл бұрын
THAT WAS A DIRTY ONE
@xavierlol9434 Жыл бұрын
Muy buen video amigo!!! Saludos desde chile
@joaobrito9642 Жыл бұрын
Thank you!!
@Jedendwa0 Жыл бұрын
10:02 Na zdrowie.
@djellouledebbah5080 Жыл бұрын
❤ merci ❤❤❤
@electricmushyy Жыл бұрын
What liquid is going in the filter before installation?? Gas?