No not all wiper arms have hooks

Love you buddy thanks

Fuse was bad as in popped?

Mine lasted 2 years but I did 75 thousand miles on it I’m not mad at it … is still going but I can see less then 1 yr I need to replace it

I am a mechanic and I liked how you did a very detailed explanation on the brake insulation.

Man these little trucks are the greatest headache you could buy and no one likes to talk about it when they touch on price points!!!! Sure its a great truck for the current price (2-3k) but sheeesh this appears to be a massive problem AND EACH ONE SEEMS TO BE UNIQUE!! e.g., you have power going to your dash in this video. and in other videos its a wide variety of blinking and solutions! My b2300 just goes dark COMPLETELY. no power to nothing. no rhyme or reason. One day I can use it powering on and off 10 times a day and the next day itll go 2 times before clicking and wiping all the power from the truck. Cant even work the hazards. SMH so my current work around is just disconnecting and connecting the battery. whatever works i guess

So the theft light that is blinking is normal yes?

Great instructional! Never see anyone address the pad spreader clips. Thats good stuff there! I usually practice using brake cleaner to remove the old grease then regrease the slide pins. You got the big can of grease too, it’s a small step with a big impact. Also, always bleed the old fluid real good. It gets burnt from the heat of the piston

Good check, unfortunately wasn't my fix. When I go to crank it, the brake light comes on but it doesn't crank. But if I go jump the starter relay it'll fire over. It's also intermittent sometimes it works sometimes it doesn't

Thank you for the video bro this was very helpful. But tbh please take care of your health you are breathing too heavily on the camera

4.0?

I just had a Gold Batter put into my 1993 Honda Del Sol today. Hopefully, it lasts as long as yours did.

Thank you man. Just saved me from a $400 tow.

Dot fluid That's a good one. DOT.

Also, That fuse powers the PCM which controls the starting system (Clutch sw., Park/ Neutral sw. positions) and can be influenced by the anti-theft module which must be able to sense the coded ignition key.

Thanks Sir ,Help me a lot 👍💪

Thanks Sir ,Help me a lot 👍💪

What a useless video

You are replacing the the whole arm W/ Blades, this is not a Blade only Replacement

I have changed my pads and then this happens. Lol

Bro thanks so much, I know motors and not really anything else for cars😂, I just bought my first “modern” car going from a 73 roadrunner to a 03 eclipse, I was so confused 😂

13:25

Not exactly what I'm looking for but it's good to know. I have an "02 Ranger4x4

At what point in the install do I get a hammer?

why did you crack the truck

I forgot that metal shim in the caliper ! Should be ok I think

Estas mierdas las hacen muy complicadas, aun no puedo cambiar los limpiaparabrisas de mi Volvo,

Frame your parts while recording.

Its a good video, but why don't you get a small tri pod? Seeing what you are doing would be better.

But mine pops up when am about to get to 60mph, won't go off until I switch the car off..

I start my part time job at AutoZone next week. Just trying to learn something here. Thanks for the video

Do you put grease on the brake pads. I see some people do thst

A year?! Mine lasted 24. Toyota. I guess they used them when there was frost.

Why did you even post this ? You did not show how to disconnect it first and then during the install "CLICK" your camera wasn't even on the subject. FAIL

the smudges may have happened from leaving that Deet on the lenses too long... better to wipe them down and immediately rinse that melting spray Off!

No I can't see what your doing, but thnx for trying

Thank you!

THANK YOU

Thanks

Always loosen the brake cap compressing these calipers can shoot a caliper piston out and they hurt when putting on the pads I like to do the inner first you lose some visibility when doing the outter first these clips are a pain in the @ss only thing I needed help with great video

Blade didn't last you have to treat the Rubber 😮 but great Vidio on installation

Thank you. Normally my mom would help me with any car stuff but now I live too far away lol

I was pretty sure I already knew how to change my wiper blades. I was pulling down on the old wiper and it would not release. Thanks to your tutorial I realized I needed to pull down harder to release the old blade. I was afraid I was going to break the wiper arm. Thanks again.

You’re no good….I can’t see

Fix your head camera.. near the end all I could see was the hood of car.

Going out to check this now, thanks man!

Oops! I meant ... I did it!🥳

Thank you!👍😄 I didn't need to finish watching the video. I just needed a few pointers and I didn't!🥳

Q

now every time I hear someone say the word tabs, I will think of you "those little tabs" 😊🙏🏻