Hello sir, may I know whether we can remove the number 4 from the equation At 2:55, which is multiplying with Li? I wanna design an inductor and capacitor for buck type inverter where LC will be worked as filter.

Hello sir need help how to contact you

sir, i can't run it, can u help me?

can you please share .m file of this model.

Base paper drive.google.com/file/d/1--8BDXpYmD-lwa3plhTTXSGbIWgf2Z7E/view?usp=drivesdk

It is asking to change buffer size parameter of rms block. How to solve this error

Great ❤❤❤

Great❤❤❤

Great ❤❤❤

Hi, thanks. why the gain is 4.6e-4.. how it can be calculated, is it essential

Hello, where could I get the specification of the converter that is shown at the beginning of the video in the design stage? Thank you

If you don't mind. Will you explain the code please. Thank you ❤

can you please provide the matlab file for this....

What you present here is different with Simulation results. This model has a bug and not working properly.

Well done.

great explanation, sir, thank you for providing valuable information, sir. Can you please clarify the three-phase current measurement? I am getting ripples os high and not at all sinusodial, please can clarify me? how to make the current waveform sinusoidal, sir

How to increase social level

How can you compare V and I ?

it will be useful if u first explain the concept behind the generation of pwm signals(why u r using these blocks)

But no doubt about your hard work and very good presentation, really appreciable . God Bless you. Keep on posting more videos.

Your work is really appreciable, But during Boost Converter Design, you mentioned the Voutput=600, i.e. the output of converter, but in actual, the output voltage of Boost converter is less than 400V, Is it the correct response, I have a doubt, Could you please clarify it.

Any did this correct please help me

hello, I have finished the model as you made. However, in Valpha waves and Active waves, the beta and reactive waves are not in phase. Can you give advice?

hello, I have made a model like above. However, after I ran the model, there was an error in the MPPT code, and I didn't understand how to correct the error. Can you help to fix it?

Dear techsimulator, I have succeeded in making a model like yours on KZbin. However, I am not sure about the resulting output waveform. Can you please comment about my model. If you wish, I will send you my model.

sir can i get this design file

I'm not getting this type of battery 7:47

Good but bad spelling distracts and detracts

لدي لوحة خرج منها اربعة اسلاك 2+و2- هل يمكنني ان اجمع كل الاثنين وربطهما مع السالب والموجب للبطارية ام واحد واحد

Which book did you refered for designing of filter ?

how can u use the PWM1 in block From if the names in the GOTO blocks are not PWM?

superb information

Please prepare the videos on dual active bridge converter

Sir i have problem on simulation output can u pls share the simulink file

What about output current sir ?

What should I do if such an error occurs?erro:A singularity has been detected in the inductance matrix. This situation typically arises when there is a mutual inductance block whose inductance parameters lead to a singular inductance matrix for that block. You must change some of the inductance values within such blocks until the singularity has been removed (e.g., this error message no longer appears). Alternatively, you can use the 'Continuous' simuation type of the powergui, with the 'Disable ideal switching' option deselected

can you give me the base paper link for this project

Very good

Equation 2 is wrong. Vx means voltage between point X and ground.

how do we decide deltaI and deltaV

Hello, can i use your knowledge for my commercial use inverter? Thanks for your helps.

thank you very much !!!, nice video

i want to ask kindly response me its not a bidirectional charger and when we add transformer how we make it bidirectional kindly response me asap

Hello Sir, thank you very much for your videos. I have a question regarding the current on the I-Grid, which appears to be distorted, and I also noticed a ringing spike on Ibat. I’ve followed all the values you indicated-am I possibly missing something?

Sir, I have tried it many times by watching the video . But i am getting the incorrect results . Plz share the slx file .

Very helpful video Thanks for this effort❤ I am confused on how to obtain the value of Kp and Ki ? Can you help me by making one video on it.. Again thanks in advance 😊

fabulous explanation

This is awesome

Hello sir, we have some questions. How to connect you ?

what happens if you remove the diodes from a panel? does anyone know?