MATLAB Simulation of a PFC Boost Converter

[@samelias2319]

could you please explain the control scheme? - the rational behind all the steps. thank you

[@notintherightmood7725]

Thank you so much for the video sir. It'd be great to see an explanation of the control scheme where you force the input current of the step-up to be a double half wave.

[@TechSimulator]

Noted

[@yi5338]

how is the PI controller coefficient calculated?

[@Syed_vlogs_YT]

Ooo wow. Really Awesome. Can you please share me the Documentation for Controller design. I want to know the control design in detail.

[@alial-khayyat8934]

Good effort

[@TechSimulator]

Thank you

[@ShreyaShree-v9v]

It is asking to change buffer size parameter of rms block. How to solve this error

[@eric4949]

Why the [Vin] multiply "1/VAC_peak" in the simulation, not multiply "1/VAC_peak^2"? Please tell me. I'm very curious.

[@kishorjoshi8981]

can ypu please mention the reference where this strategy came from

[@sofiabarriuso8845]

Thank you so much for the video. When I do my simultation following your steps it takes about 4 minutes to be completed. Do you know how to speed it up? Or why can it take so long? I just put 0.6 seconds

[@gbo4942]

Thank you for this video. Which control method did you use in this video? Is this avarage current control method?

[@dishikapoddar8121]

Sir, can you tell me how you found values for all the components in the converter?

[@mariamkamal2408]

Is it possible to know the reference?

[@yahyaymn2781]

Thank you so much

[@anoopkumarniravuparambil1114]

Multiplying Unit vector with voltage control loop pi output gives an Iref of 100Hz speed. Simulation its fine, but this will not work in hardware if feedforward duty is not there. Feed forward duty + Compensator duty should be the actual duty.

[@rachna5156]

Sir can u please tell how u tune parameter of kp and ki?

[@barathnarayanan4333]

after very long time bro and hope you remember there is a channel bro one request please do video on space vector technique closed loop for motor load

[@kandurilakshmanpavan1580]

Can you do simulation for PFC CUK Converter

[@jason_0872]

How about PFC buck Convertor ?

[@CookiePepper]

Voltage overshoot at startup is usually not acceptable. How it could be solved?

[@TechSimulator]

soft start mechanism

[@pulonathan6435]

Could you please upload some videos on interleaved boost converter, battery storage system with fuzzy logic controller... Please ....🙏🙏🙏🙏🙏🙏🙏

[@TechSimulator]

noted

[@gknaveenkumar4391]

Why there is a dead zone in the input current at every zero crossing ... Boost PFCs shouldn't get dead zone

[@satyajit7417]

Can u please make simulation on bidirectional PFC Application :- ev chargers( V2V , V2G)

[@manoharchoudhary7648]

+1

[@montech2417]

Please make mppt with flyback

[@anilkumartiwari5165]

How to decide rated power in any simulation??

[@TechSimulator]

You can select whatevr number you want

[@truongle8983]

Please give me the theory file.

[@finance_time]

Sir could u plzz upload this simulation file ..so that we can run this file in our system

[@TechSimulator]

pls contact me at my email

[@montech2417]

Make flyback applications

[@psrikanth6477]

Same control diagram not working in MATLAB

[@elonmust6473]

in the PID controllers, select descrete time instead of continuous time

[@elonmust6473]

for both PID

[@jiuyi8364]

Thank you so much