Left the vid when he said some ab welding aint doin all tht

What is the name of crimping machine & cost please

out of all videos i seen, this one is perfect and straight to the point! thank you! 🙏

Yourl refuse tontell people waht type of rods to buy

Is there a color you look for when you have enough heat? Or just how the rod melts? Great video!

I’m new to doing air-conditioning and I just recently bought the crimper. When I put the bead lock fitting on do I need to put gasket inside the brad lock before crimping? Or only the gasket on the outside that hooks to the compressor? Thank you in advance.

Dear Sir, which site can I find Thus dies assembly, the cone,fingers, bolts, and housing

Time is money, and I see this as a complete waste of time. Just purchase a new one.

is it possible to repair the metal pipe?

Really nice instructional video. Thank you- I picked up a lot of good tips. This is perfect for working on vintage vehicles with old hoses made of unobtainium. To the chuckle-heads below... watch ALL 5 STEPS! One additional point/suggestion. In addition to marking the orientation, it is also helpful to match the natural curve of the hose. So make your marks at the outside of the curve, and then load the new hose the same way.

I know that welding after cleaning with brake cleaner is lethal doesn’t brazing have the same effect?

Crimping a hose is not a repair! We want to see how you assemble the hose with what parts and names crimping is the easiest.

Did you use flux core rod? I didn’t catch it if you mentioned.

Jesus wept man, why did you not just cut the crimps and replace the pipe with new crimps. Welding? You're mad honestly.

Necesito comprar esa herramienta por favor proporcióname un número de teléfono.

pre-fluxed alluminum brazing rods. Ideally, for aluminum soldering you want the flame temp to be 600 degrees F to 800 degrees F

hello, what kind of solder do you use to solder the pipes and at what temperature do you solder?

Safety glasses to cut aluminium with hack saw 😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂

That's my brother! Great job! Andy liked this video😄

Brazing with what? Solder?

What is the brazing rod made from ?? What is the flux your using ???

Hi, Nice video. I owned an automotive air conditioning and radiator shop for 30 years. I opened it in 1973 and it is still open today by a former employee. I have few comments: (1.) I was taught to clean aluminum with a clean stainless steel wire brush . (2.) I would not have dipped an A/C fitting in water. (3.) It was always a complaint of mine that they didn't make A/C hoses with reusable fittings in the first place. (4.) The R-12 hose barb fittings could be reused. They wrer held on to the hose by the center of the hose. We double clamped them or crimped with A/C hose ferrules. (5.) Barrier hose does not use hose barb fittings to hold the fitting to hose, but uses a bubble crimped ferule. (6.) I experimented with adding A/C hose crimp ferrules to factory hoses and then bubble crimp them. One method I used elongated the hole in the crimp ferrules so it could hook onto the factory hose fitting. I have noticed that some company uses a cage assembly and then special clamps.

What kind of torch and flame gas you are using. I use butane gas CAN and normal torch and flux inbuilt rod to weld but 90% of it fails. Pipe got white carbon and material doesn’t stuck and rod doesn’t melt properly. Please tell me about the gas, torch & rod u are using and if possible give me link of the products

Mark the ends then throw it in the bin, ain't worth trying to fix 350 psi air con tubes, I tried lol, just spent the last 2 hours removing my old Aluminium tubes ready for the new ones. Most air compressor hoses are rated to 270 psi. So Imagine how puffed out they get with constant 350 psi. 😔

You forgot to put the nut on.

Well, I was curious about technique. But equipment will be too expensive for a one or two time use. Think I'll just have it repaired. However with this knowledge I could do it if so inclined and if it was cost efficient. Thx for posting

Hello, can this tool be use to crimp oil cooler hose for cars? thank you

That was pointless

Need your address

Hello

what is the requirements for the hose ? where to find them ? thanks!

Price yenta

Hose is short.

Where can I send my hose to be fixed? I have no need to buy a crimping tool I'll use once.

Where can I buy welding rods?

Smart way to only change your 4 dollar hose not the whole deal when it goes bad

The specialty fittings to repair an A/C hose cost as much or more than an entire replacement hose. Repairing it utterly pointless.

Where can I buy all this stuff the crimps set and the hoses please

I tried this with no luck .. what rods are you using?

AN soft jaws might help on holding fittings too

What is price??

Type of flux would be nice as well as type of rod

Wow ITS very much

Hi, do you guys sell all that is needed to do this? do you have a catalogue?

im going to crimp garden hose fitting w ferrules, but my ferrules need to be longer as only 2 of the 3 indentations fit on the ferrules, dixon,and dramm make hose crimper dixon model 860 large hose crimper,they work differently,but similar results,dramm ferrules only fit their thicker hose ,so it takes some trial n error to find milton or gates,gilmour,or other propper sized ferrules for a good crimp on barbed fittings,for that factory look,without hose clamps, pex crimp rings,or clam shell,repair fittings,generally 5/8 and 3/4 I.D.

The part where the bolt goes in to tighten the hose assembly to the compressor, is it able to rotate around the pipe? I have another compressor whose bolt hole is on the opposite side as compated to the old compressor but without removing the hose I cannot tell.

At the 2 ends of the AC lines are adapter plates that bolt to the compressor so that the AC line stays in place. Can u tell me if those adapter plates are free to rotate around the pipe? Some Compressor has bolt holes that are at the opposite side so I dont know if i need a new pipe or just rotate and reuse it. Thanks

I need one did for a Oldsmobile

Whats the name of this kind of clamps?

with this can of propane can this be done to copper also