Dunce - Cosmoline does not contain lapping compound.
@Leman.Russ.6thLegion3 күн бұрын
I run LMT stuff. Every and any issue is basically solved with use of either partial or full flo thru cans. I use an rc3, and a knights qdc, and never needed to change buffers or spring weights.
@320epdmk5 күн бұрын
Just got my Polonium out of jail and have the Atlas XL with Q cherry bomb on my 5.56 rifles. Ive noticed before ive even shot that if i crank down on the hand tight to the muzzle device, the QD will stay on when i unscrew the can. Suggestions???
@silencerstudent93815 күн бұрын
@@320epdmk u shouldnt be cranking down on that joint. Its like over tightening the lig nuts on your car. The threads stretching puting more force on the taper requiring a multiplication of effort to get it back off. Finger tight is all it takes to properly tighten an atlas. That said rockset or locktight the mount to the can should insure the mount never backs off during normal use cases
@ThompsonNydia-m8s7 күн бұрын
Davis Robert Martin Richard Jackson Sandra
@silencerstudent93817 күн бұрын
@@ThompsonNydia-m8s a lot of names
@DDadams014 күн бұрын
21:45 If you're interested in that - I hope you've seen the new KAK K-spec down vent BCG by now. Thats what you're looking for.
@ThirtyOught625 күн бұрын
What is the NAME of these new attachments???
@bkhix208Ай бұрын
Get in shape host.
@colbyc.6698Ай бұрын
Do different muzzle devices change the tone of silencers?
@silencerstudent9381Ай бұрын
@@colbyc.6698 they can yea and they deff play a part in the flow characteristics and therefore can either positively or negatively change how a can sounds (loudness)
@colbyc.6698Ай бұрын
Thanks for the reply
@wwaldokАй бұрын
My God. You sure can waste time.
@ICanDoItMyselfАй бұрын
Closer to an A1 flash hider than an A2.
@timb7397Ай бұрын
Had any issue with the ht galling like dead air claims?
@silencerstudent93815 күн бұрын
@@timb7397 keeping the taper clean (wipe it off with the end of of ur shirt or a rag periodically when u remove the can) helps make sure u always get a proper seal. U can also run a small thin layer of antisieze on the taper as good habit say every time u clean the rifle also do that.
@44MagАй бұрын
I just got mine today. Man, that back plug is tight, and they do not include a tool to take it off so you can swap pistons or put a spacer in it. (Could not find one on their website either) - Basically had to get pliers after it. I think I read the Rugged tool fits it, so I will likely order one of those, or at least one of the third party made ones. Everything else looked good with it. Hopefully I will get to do a desk pop with it tomorrow.
@silencerstudent93817 күн бұрын
@@44Mag should have been a little silver looking slug of metal
@44Mag7 күн бұрын
@@silencerstudent9381 Yes, it came with that tool, and it is used to take the front cap off. The tool does not work to remove the blast chamber. For that, you have to either use pliers, or buy a tool to fit it.
@ICanDoItMyself2 ай бұрын
2 years later, most are still out of stock.
@silencerstudent93812 ай бұрын
@@ICanDoItMyself they sell that many. U can find them anywhere
@Williamkendmarz2 ай бұрын
Any ideas what would be a good bcg for a 11.5 ?
@silencerstudent93812 ай бұрын
Just go with any mid to high end bcg. Id run a midlength gas system
@Williamkendmarz2 ай бұрын
@silencerstudent9381 it's a carbine 11.5 , super duty by geissele
@musician4452 ай бұрын
I think LMT finally released the material for the bolt, I recall reading somewhere that its Aeromet. The bolt lug they removed is supposed to load balance the rest of the lugs. Its generally understood that the lugs that fail most often are the ones neighboring the extractor. By removing that one lug opposite those two, it supposedly reduces the stress on them exponentially. For me, due to the proprietary nature of their bolt, I opted to just buy the carrier only, and install a Colt bolt. Extractors are wear items as are the springs, and not being able to easily replace those is more concerning to me, as I will likely need to replace an extractor sooner than the entire bolt itself. And if one is worried about the extractor spring itself failing, you can use an upgraded Sprinco that has a much longer cycle life. NOTE:: chrome Sprinco silicon springs need lubrication as they are not as corrosion resistant as stainless, without lubrication they can fail prematurely in wet/salty environments, just lube your gun like you should be doing anyway and it will be fine. Also Leitner Wise has now released their carrier I think. (Paul Leitner Weise is the LW of LWRC as I understand it, no longer affiliated.)
@tylerhestla30222 ай бұрын
I've got a 12.5 aero upper with a 12.7 handguard. The inner diameter is 1.2 . When I measured from where the barrel threads start to the end of the hanguad is 7/8. Would the XL Atlas sit down inside the handguard enough to run a lahar 30 ?
@romebowermaster50603 ай бұрын
Have a quick question, looking to suppress a Glock 19 came down to these conclusions. RS9 (or RSP if I can find one), Omega 9k (readily available), or wait to see data from CAT Street Crack. Thoughts or opinions would be greatly appreciated!
@silencerstudent93813 ай бұрын
Rsp might be hard to find as they are working on a gen2 right now. Cat has some things that are coming to lights about manufacturing but generally proven they can hit the sound performance one would also be looking for so deff in the conversation for a great choice as well. Can’t say if honestly recommend anything else
@romebowermaster50603 ай бұрын
@@silencerstudent9381 So from your experience either try for a RS9 or wait for Street Crack? Im fine with either of those Ive just been considering the Omega bc I haven’t heard anything bad about it, it just isn’t as quiet as its competitors.
@joewest25603 ай бұрын
Chuck key is stuck in my brain... dummy
@basrutten6414 ай бұрын
Certifying for a Polonium 30. Interesting how this podcast was nearly its inception. I am totally stoked. What a couple of cool fellas! Best of luck of your future endeavors- I will definitely be watching for your new products
@carlvonfuckwits29344 ай бұрын
On rearden what is the difference in options for 25degree taper square or face?
@CRAZEDX1003 ай бұрын
Tapered barrel shoulder or square shoulder
@Shoota45acp4 ай бұрын
Years ago when I built my 300 BLK I put an AAC 51T Brakeout on it as I wasn't ready to put myself an an NFA list. Now that I'm ready, AAC 51T is obsolete! Dang! Thanks for some great info.
@albertptran4 ай бұрын
Thanks for sharing!
@CalmBeforeTheStorm765 ай бұрын
This did not help me remove my stuck brake. But, I appreciate your box of mounts.
@ethan5.565 ай бұрын
Debating a rearden xl or a dead air xeno on my A-10 warthog 5.56 can
@RedDawnReadiness5 ай бұрын
Do you know if the Rearden XL is usable with silencer co breaks ?
@PkwyDrive135 ай бұрын
Any recommendation on a mount for precision rifle with Diligent defense enticer S? 6.5cm, dedicated suppressor but will be removed each time to fit in range bag lol. Can't decide if direct thread or taper qd mount would be better. And which rearden or LPM brakes best?
@shawnwillis75615 ай бұрын
Can you work on your own can or do you have to send it to an FFL07? I really want to lighten and recore a cheap, heavy radical Firearms can that sounds horrible.
@shawnwillis75615 ай бұрын
I've been looking at jail breaking a couple cans through them. I wanted to send in a Radical Firearms can but I guess they won't work on RF cans.
@PkwyDrive135 ай бұрын
Where's the enticer S video you said to watch? I don't see it in your channel
@KevinWood445 ай бұрын
Aren't the Sharp XPB supposed to be incredible too?
@hairydogstail5 ай бұрын
The LMT enhanced bcg cam path is longer in the straight part to allow more residual gas pressure to decrease before un-locking..The down side is these enhanced carriers will not run as reliable in the rifle system gas tube which is why the military rejected them..For short gas systems like the carbine length gas tube they work as designed..Jim Sullivan discussed this in his interview for Small Arms Review..He incorporated a longer/straight cut in the cam path for the Stoner 63 for this exact same reason....
@rccaraddict2945 ай бұрын
Absolutely PHENOMENAL video man ! Thanks for this one. Now I know exactly what I want to order for my new Ventum 762. Thanks
@chadmccormick14126 ай бұрын
I just ordered the Enticer L in stainless steel. I’m hoping it’s not too heavy for my .308 bolt gun or AR. Lol! What do you guys think? Love your content sir!! Please keep it up!!
@silencerstudent93816 ай бұрын
I like the stainless more then the ti, i think ull be very happy
@chadmccormick14126 ай бұрын
@@silencerstudent9381 awesome! Thank you for the affirmation. Lol! Is that heavy to you? I’m hoping it’s not too heavy for my AR and bolt gun… Love your channel! It’s so informative and knowledge driven.
@silencerstudent93816 ай бұрын
@@chadmccormick1412 i think even in stainless theyre light
@chadmccormick14126 ай бұрын
@@silencerstudent9381 man that’s awesome! The bad thing is my wait hasn’t even started yet. My dealer had to order it for me. Apparently they can’t keep them in stock!
@PkwyDrive135 ай бұрын
@@silencerstudent9381I bought one a few days ago, the S. And I was also worried it'd be heavy, but I want today and looked at it, even the steel is light. I handled the S and L and they didn't feel heavy at all to me. Mines for my bergara B14 HMR 6.5
@gocoach87076 ай бұрын
Are you supposed to align each cone with the cutouts in the same place? Mine throws all over the place? I shot it twice and my tube is completely carbon locked to the pistol housing. I can take the piston out but can’t unscrew the tube from housing. Do you have any recommendations?
@silencerstudent93816 ай бұрын
ya but if u cant its not end of the world
@grantham11496 ай бұрын
What does the double clipped do? Or how does it benefit?
@silencerstudent93816 ай бұрын
mainly changes the flow rate in the can, which if a can is choked off it will suddenly help and give a positive result but if the original single was correct then it will increase it too much and have a negative result.
@davewalls7526 ай бұрын
Can,t continue watching with chuck key let in and playing with the controls and bouncing metal of the ways is this guy qualified ?
@silencerstudent93816 ай бұрын
if it was a 2hp plus machine i would care
@davewalls7526 ай бұрын
As a retired machinist a big NoNo is leaving chuck key in chuck !
@Jack-ny7kn6 ай бұрын
Caveat to the caliber. That's actually a minimum, but not the maximum. If it's marked 9mm, the bore of the suppressor has to be a minimum of 9mm, but there's nothing saying it can't be 10mm, for example.
@4g63mark6 ай бұрын
How is the visual signature between the Hydrogen and the Polonium considering the difference between titanium and steel? How much more quiet is the Polonium K vs the Hydrogen K on a 13.7" - 14.5" 5.56? 2-3 decibels maybe?
@silencerstudent93816 ай бұрын
pewscience recently did some testing on hydrogen that should help you make a decision
@General.Legion6 ай бұрын
Just put two Otter Creek Lab cans in jail. I've been looking at OD mount and was leaning towards Deadair Keymo, Keymicro, and xeno. This just changes my mind and will look into Rearden. Great info on all OD mounts.
@silencerstudent93816 ай бұрын
Good choice!
@harveylin35487 ай бұрын
Getting my can tomorrow and is going to be using Rearden, thank you!
@timgleason29107 ай бұрын
Does JK still do Form 1 builds?
@GregMHirsch7 ай бұрын
Well done!
@IDFWU6507 ай бұрын
Can you pin and weld these with ease?
@jcglock407 ай бұрын
What Rearden QD do you recommend for a YHM R 9 for the M4 platform ?
@jcglock407 ай бұрын
What Rearden QD do you recommend for a YHM R 9 ?
@silencerstudent93816 ай бұрын
i believe the r9 is 1.375x24 so regular atlas
@fattigla7 ай бұрын
Really like to do something like this with an old, out of production silencer that I don't use much anymore.
@silencerstudent93816 ай бұрын
send it to ecco!
@fattigla7 ай бұрын
Awesome info! Thanks for putting this together!!
@silencerstudent93816 ай бұрын
You bet!
@turnerables8 ай бұрын
Would the double port brake with regular atlas on the Nomad L? Debating this or the Xeno
@silencerstudent93816 ай бұрын
the nomad has a small bc but i believe it still fits just close to first baffle
@MrMercaholic758 ай бұрын
Where can I find the blueprint for that 10.5 suppressor?