Sorry to hear that. You can submit a RMA and get a new unit or your money back if they are out of replacements. I had a Hisense tv that went dead, after submitting the RMA, they sent a technician to check the TV and then refunded me the money.

If it's in the return window, I will return it and not bother with it. Thank you for watching

Glad I could help.

The unit should have 2 fans: one for the evaporator coil on top where the cold air comes out, another for the condenser coil to keep the compressor temperature down (bottom one). Make sure these fans, especially the bottom one are not turning off. These units are designed with electronic pressure/temperature monitoring in order to protect the compressor, so if the fan will turn off, it will signal the compressor to turn off too. Also there should be a temperature sensor attached to the pipe next to the condenser, check it make sure it's not clogged. If this is not the case, check the drain pans for water accumulation. Excessive moisture will fill those pans pretty fast, so to avoid flooding the compressor will stop while fans will still run to evaporate that water. It might be a failing capacitor too not providing enough juice for the compressor to run smoothly. I don't think it's the main board. Hope this helps

Hi there. No, I don't speak russian. To answer your other questions, if everything is working but no cold air is coming out, the unit most probably has a leak and it's low on refrigerant. Recharging the unit without appropriate tools and equipment is not a DIY job. These units do not have a recharge port/valve, so fixing the leak and recharging costs more than a new unit. If your unit has a leak and you are out of warranty, discard it and get a new one. Thank you for watching.

@@strykergaming_ngadgets oh, okay, I see… well, thanks for the answer, anyway I sold it today already and will buy another one 😅

I’m in the same situation not sure what to do

So, compressor is starting and cold air is blowing, than after some time compressor turns off, fans are still spinning, after a while compressor starts again and cold air blowing again, is that right? If this is the case high humidity can cause excess water accumulation inside the unit and in order to avoid an overflow, compressor shuts off, while spinning fans help evaporate the accumulated water in the drain pans. Check for water and drain the unit when the compressor turns off. Also make sure the fins and both grills, back and the one inside are clean. Hope this helps

Thank for the suggestion. I didn't consider that, these capacitors are pretty cheap to replace, a soft starter is more expensive.

Tailgating drivers are usually angry. I bet he was saying or yelling something while driving.

Drive and stay safe

I was in accidents myself, twice. First time I stopped at a red light and the car behind me just kept going without even braking, hitting the rear of my car, pushing my car into the car Infront of me. Second time at an intersection someone ran a red light at ~60 mph T boning my car. Barely had time to react and angle my car a little. As a result the impact was in left rear passenger door at a little angle and ended up spinning like crazy. Good thing I had no passengers. If I hadn't react in that split of a second and angle my car, the hit would have been a full force T-bone directly in my door and who knows if I would still be here. In both accidents my cars were totaled.

@teresaweaver4441 I completely agree. People care less, drive more aggressively, and have less patience. When I am on the roads, I constantly check the mirrors and try to stay away from reckless drivers. It's more stressful to drive now than before covid

I have these settings for my M27Q Rev 2.0 OSD: Settings - Picture - Custom 1 Brightness - 65 Contrast - 50 Color Vibrance - 10 Sharpness - 6 Gamma - 2 Color Temperature - User Define RGB - 98-100-94 DCR - OFF Refresh Rate - 165 Hz Keep in mind: every monitor is a little different, even if they are of the same model, so settings that are good for me, might look a little different for you. Hope this helps and thank you for watching

@@brendentwenty unfortunately some drivers don't realize that their actions can inadversibly affect and change other peoples lifes

@@strykergaming_ngadgets ain’t that the truth!

@@truth.honesty The actions of that driver made no sense to me at all. He had plenty of time to slow down and stop, yet he chose to put himself and others at risk.

@@strykergaming_ngadgets That's what I said.

@johnholeman2052 yes, every day this happens, and every day because of something like this accidents happen and people suffer. So why this driver with more than enough time to slow and stop does the opposite?

Yes, the electronic components are usually under the front cover away from moisture and heat. It's highly unlikely for the capacitor to be accesses by removing the back cover only. Thank you for watching.

@@agustinmartinez6658 I got mine on Amazon.

@@KEField Hope this helps. Thank you for watching

You should just go and return it, then you can get a new one.

@ariza7400 Return it and get a new one. Costco offers 90 days returns on appliances.

Same issue, a danby from Costco, and they’re sold out. 🫵🏻🤬

@@chadland71 Sorry to hear that. They are usually available at Costco in spring. I think you can still find Hisense and Midea at Costco online though.

You can call an appliance repair company. These portable AC units work on the same principle as a fridge. If the cost of the repair is comparable to the price of a new portable AC unit, it's better to buy a new unit of course.

Try these steps first kzbin.info/www/bejne/e3u8doOpdtCrjdk If you are not getting any error messages, check and drain the unit. There might be water accumulated, the unit will start and then to avoid flooding will shut off. Pay attention to the fans, if a fan turns off before the compressor, the issue may be there. There is a sensor right in front of the grill and usually it gets dirty pretty fast, you can clean it using a can of compressed air. If none of these, it still may be the capacitor. The capacitor acts as a small battery to give the compressor that extra juice it needs to start and run smoothly. A bad capacitor might still hold some charge, but not enough to make the compressor operate normally. Hope this helps. Let me know if you were able to fix the issue and thank you for watching.

@@strykergaming_ngadgetsmines does the same thing it clicks on then shuts back per blowing warm air mines is brand new just bought it today why won’t it stay on

@@toshalewis1285 I advise you to return it and get a new one. It's not worth the trouble if it's within the return window. Thank you for watching

Check to make sure your condenser fan motor is running. Sounds like your compressor is kicking off due to high temp.

@patrickdesilva1677 Let me see what I can do. I called a couple of retailers, and they cary the latest version only. Finding Rev 1.0 might be an issue. I looked at the specs and, except for the refresh rate of 240Hz, built in speakers and price of course, these monitors are pretty similar to M27Q rev 1.0 and 2.0 (almost makes me wonder if M27Q-X is not an M27Q with some firmware features unlocked :))). From specs, M27Q-X Rev 2.0 has a faster response time and better color saturation. Response Time of 1ms MPRT is better than 1ms GtG. If you don't mind me asking, what do you need a 240Hz refresh rate monitor for?

@ayarimaher7150 If the compressor is working, fans are spinning, but no cool air is coming out, then there might be obstruction in the refrigerant lines, or the unit has a leak. Try to run the unit in supercool mode for an hour or so. If it's still not cooling - then the unit has a leak, and it's low on refrigerant. Fixing the leak and adding refrigerant is more expensive than buying a new AC unit. Check your warranty and call the manufacturer if the unit is fairly new. They might work with you if it's a leak. It's kind of a manufacturer fault that lines were not soldered the proper way. Hope this helps

@@strykergaming_ngadgets I posted this same question in the other video but glad I found this comment. Going to let mine run on high and cold for an hour and hoping for the best. I’d hate to purchase a new one since we’ve only had ours for 2 years and the warranty conveniently expired before it started failing to cool.

@@CARMINE_YT sorry to hear that. Hope you find the info helpful

@@strykergaming_ngadgets no worries, it helps. I left it on for an hour and still didn’t cool. Will try to dust as much as I can but it’s potentially a leak with the refrigerant which means we’re likely going to have to scrap it. Avoiding all LG products…

@@CARMINE_YT If it's a leak, the unit is done.

Fingers crossed!

Sorry to hear that. Try to follow these steps, they apply to most manufacturers kzbin.info/www/bejne/e3u8doOpdtCrjdk If everything is running and unit not cooling or not colling as it used to, then best case scenario there might be an obstruction in the tubes and setting the unit to supercool mode for a couple of hours might clear it and have the refrigerant flow properly; worst case scenario - unit has a leak and it's loosing refrigerant and eventually will stop cooling completely. Fixing a leak and refiling a portable AC unit costs more than buying a new one.

Same

My Frigidaire Gallery portable AC is new but it doesn't blow cold air at all what could the problem be??

@@eugeniagutierrez5013 If the compressor kicks in and everything is working except for unit blowing cold air, most probably unit has a leak and it's low on refrigerant. Fixing the leak costs more than a new unit. If it's within the return window, just return it and get a new one. Also most of these units come with a 2 year warranty in case you cannot return it. You may also try these steps. Manufacturer will ask you to perform them in case you're starting a RMA. kzbin.info/www/bejne/e3u8doOpdtCrjdk Thank you for watching

This is posted to the wrong video but I will gladly answer for you. At 1080p and 1440p with i7-7700 and RTX 4070 Ti you will get about 40% -50% bottleneck. This combo is a waste of money. Check this video kzbin.info/www/bejne/omqtmqmHZ95-hqs At 4K i7-7700k and RTX 4070 Ti have almost no bottleneck; but check the frametimes - i7-7700k has double the frametimes of i7-13700k which results in a choppier gameplay. kzbin.info/www/bejne/l56Wd6alodN0aZo Pairing RTX 4070 ti Super with intel i7-7700k will not give you a lot of benefits because the GPU will be limited by the CPU in any case. i7-7700 it's way too weak for RTX 4070 ti Super. The get all RTX 4070 ti Super offers you will have to upgrade the CPU too, otherwise is not worth it. Any GPU faster than RTX 2080 will cause a bottleneck if paired with i7-7700k. Hope this helps

At 1080p and 1440p with i7-7700 and RTX 4070 Ti you will get about 40% -50% bottleneck. This combo is a waste of money. Check this video kzbin.info/www/bejne/omqtmqmHZ95-hqs At 4K i7-7700k and RTX 4070 Ti have almost no bottleneck; but check the frametimes - i7-7700k has double the frametimes of i7-13700k which results in a choppier gameplay. kzbin.info/www/bejne/l56Wd6alodN0aZo Pairing RTX 4070 ti Super with intel i7-7700k will not give you a lot of benefits because the GPU will be limited by the CPU in any case. i7-7700 it's way too weak for RTX 4070 ti Super. The get all RTX 4070 ti Super offers you will have to upgrade the CPU too, otherwise is not worth it. Any GPU faster than RTX 2080 will cause a bottleneck if paired with i7-7700k. Hope this helps

Glad you were able to save some money and have your unit working again

Same here

Dude it worked

Glad it was helpful!

Main difference is subpixel layout BGR for Rev 1.0 - less clarity in the text; RGB for Rev 2.0 clear text and better color saturation. I have the Rev 2.0 and love it, been having it for a while and had no issues. If the monitor works and you like the way it's reproducing the image than it's a good thing. Thank you for watching

I agree, map is kind of small in length and narrow, especially for vehicles

Will do. Thank you for watching

I don't see why not. Connect the monitor and try the updates. If it doesn't work, go to the display settings and choose to display only on 2 (native laptop fisplay will be 1). Perform the updates, then change to your normal display setup. Hope it helps.

Room temperature ~75 - 76 F. There is no undervolt or power limits, everything is at stock speeds in this video. Processor doesn't get hot because in games CPU usage is ~50% - 60%, so an AIO 240 mm will keep it cool. No with this setting the Cinebench test is not great. CPU will hit 100 F pretty fast and will throttle. Currently I have the CPU running with a -0.05 undervolt, 243 limit on power and also installed the contact frame to prevent bending (13700k bends same way as 12700k with original retainer): with these new settings on same AIO 240 mm cooler, quiet settings in Cinebench I'm getting a score of 30,224 more or less, and CPU runs at about 85 to 87 F max. Hope this helps and thank you for watching

Thk you man

@@AlexResende33 You're welcome. Feel free to post any other questions you might have

It's the CPU. While it will give you the frames, the actual frametime (time to draw frames) is not great. Upgrading the GPU will not solve the problem. CPU is just not fast enough. Check out this video kzbin.info/www/bejne/l56Wd6alodN0aZo and look at the frametime graph 17-7700k vs i7-13700k at 4K. Frame time for 7700k is almost double of 13700k. That is your frame rate drop and stuttering. Let me know what you think.

In addition to HDMI/Display port, make sure you use the provided USB-A to USB-B cable to connect the monitortothecomputer. The monitor has Usb A ports too. If you use Usb-A to Usb-A cable, it will not work. Hope this helps. Thank you for watching.

@@strykergaming_ngadgets Thanks. I seem to have misplaced the included cables tho :/ so I need to order a new one..

@@marxthe.2651 You'll need that USB-A to USB-B. That is the only way to update

Glad to hear that

Great CPU once you tame the temperature on it.

Gigabyte Control Center is a program that comes with most Gigabyte apps installed and you access them directly from there. Side kick is just a single app designed to update firmware and adjust the display properties. Most of the manufacturers usually provide one or two firmware updates, and multiple driver updates. Same goes for Gigabyte. Thanks for watching

It's not a problem, it used to be one in the past before clear type were the text will be blurry.

If you dont like something even a little dont buy it or return it if you have that capability, there is no 3rd option

@@LeCommeiLFaut I don't buy it online, and most stores don't have an RMA option But apparently scratched batteries, missing accessories do not speak well for the integrity of this product. And this product was purchased from an official ASUS distributor And what are we doing ? We are talking about a product that costs $700! In my country by exchange rate even more...

@@AndreiHristow If you have an opportunity to whatch board before buying you have to do it, buy only after you checked package

The motherboard is the soul and body of your PC. Damaged or faulty motherboard will make your PC not work at all or give you constant issues. If it dies on you completely you will also might need a new license for your OS too. My opinion, if you have droughts, don't get it and find another retailer. It's your money and your time. If it's advertised as new and you pay for new you should get a new unused one.

@@strykergaming_ngadgets yeah agree, cpu, board and ram are all crucial. Btw did you ever experienced bad Lod in games /juddering effect? If yes, is it cpu or/and board?

Refurbished was dead on arrival. Would not boot. Board diagnostic lights were showing CPU and RAM issues.

dont buy refurbeshed - 99% you will get board with closed subsystem(ME)

Good question and I completely agree the manufacturers should put branded seals on box or on anti static bag. If they are broken and resealed it will be easy to determine if the sold product is new or refurbished. On the other hand this will cut some profits for some distributors, don't you agree?

You are welcome

@@strykergaming_ngadgets I recently encountered a problem, every time I connect the monitor OSD wire to the computer case, it says that the wire is not connected, but I am completely sure that it is connected.

@@parsa2302 Are you using an USB-A to USB-B wire?

@@strykergaming_ngadgets I use the DC to USB cable that came in the box.

@@parsa2302 Not quite sure what are you talking about, DC to USB it's a charging cable, mine didn't have such cable, in any case you need an USB-A to USB-B cable for the update to work. Hope this helps

I think I explained it in this video, also check this one for more info: kzbin.info/www/bejne/raumkpmOg7CCqrs Thank you for watching

cap the framerate with riva tuner

DLSS is meant to take the load from GPU and put on CPU. It runs the game at a lower resolution and then upscale it. This will load the CPU more. Did you try this kzbin.info/www/bejne/nXLNf3R4d9p4jqc

They probably got a good deal on those panels, why not make some extra cash