Great, to the point video, I think you just diagnosed my problem. Thank you !!

Thank you!!!

Hello, i have a Raker prop i want to install on my Yamaha F250. What adaptor should i buy? Thank you

The brass thrust washer is not properly seated in your demo.

i just think of it as opposite sided like air craft lights. left hand is down its a right and rt hand down is left. acft lights are red on left right is green. Great demostration and thanks for taking the time to make it. cheers.

But how to remove an existing one?

This is a top 10 best god damned video on the internet. Went through so much BS before I found this. Thank you!!!!!

So CCTX 1:38

If you torque the nut to 55lbs but back it off to align the nut flats to the keeper tabs, the nut isn’t any longer torqued to 55lbs.

I love you. Seemed like alot of play after i tightened it and wasnt sure if it was normal

My boat is a 2017 tracker Sportsman 2072 when I took it out this week I would give it Full Throttle it wouldn't go over 10 mph and it didn't sound like it was getting full throttle any suggestions, it starts right up and idles fine its a mercury 150 with 90 hrs on it. I did get low voltage when I'd go to put the prop up or down. And it would peep sometimes low voltage.

How do you stop prop chatter?

How do you take the old hub off? Just bang it off with hammer?

This was the best tutorial video. Thanks!

Thank you very much for the great information.

Can i put a flo torq hub in a yamaha prop and put it on my mercury?

Nice Explanation Thank you.

Hi Prop shop Inc My kit did not come with the o-ring. Can you please advise what size is the o ring?

Do I need to block the shaft from spinning while tightening or untightening the nut? How do you do that?

Is it normal that little play that you have? Do you also have some play in the axial?

Does this fit a 2023 300r?

Is there no need to lube that o-ring?

How much torque should nut be tightened to when reinstalling prop?

So what if your boat goes into gear prop spins but it just revs up but won’t go anywhere only can go one knot

The instruction in my Mercury hub assembly states 100 ft lbs

This is dumb since one does not know which side prop is sitting if makes a difference. Should do this on a MOUNTED prop!

I have a 2018 mercury 100 hp command thrust with today a black max aluminium 17p that slips on the water under hard accelration or trimming out on the outboard. I bought a slightly used mercury vengeance 19p can i use the samme flo torq ii hub kit i use on the black max on this vengeance prop?

What advantage would it give tournament boats to run left hand props?

Would love to see a video of a Solas Amita 3 E series 14.5 19 pitch installed on a alpha 1 Gen 2

Great simple tip to always remember. Right thumb in the hub, fingers up =RH

The brass,compition propeller,are you showing us back or larger end of taper or opposite ,( nut end or cutless bearing ( side/ forward

Is the half nut still considered a jam nut even though the jam nut function is being done by the full nut/second nut?

Is Pi value is 22/7 or 3.141 ...what to consider

In all the videos I've watched about installing these Flo-Torq II hubs, nobody ever shows greasing the thrust washer but they always seem to stick when you take the prop off. Is it ok to grease the back and front of the thrust washer while you're greasing the spline?

So smart !

Super simple!

Which side of the propeller is facing the table?

When I tighten mine up +-50 lb. mine seems like it is dragging on something along one side. It’s an old flo torq I had for years but a new / old lower due to a rock last fall. All parts are as they should be yet when I take it much beyond wheel bearing right it seems to drag in one spot. I’ve never seen this before and will stick the old style prop back on till I figure it out. Any ideas what to look for?? Alpha 1 1St Gen. thanks

You don’t bother lapping it?

Best info for changing the hub. Thanks

Thank you. Short and to the point and accurate. The only thing I would do differently is put a lock washer between the two nuts.

THANK YOU VERY MUCH!!!

Can I buy a Prop from your shop?

How easy should I be able to spin the prop by hand. ( checking alienent)

Always have extra keys for shaft to propeller security. Easy to drop.

Do you know the size for the o ring

Great ! I was installing an impellor wanted the rubber blades to face in the proper direction . Thanks !

Thanks

Is lateral play in the flotorque 2 Merc hub normal. 1 year old Merc 50 4 stroke. Was like this since I owner the boat. 1/8 inch lateral play.

is this a LH prop