man you are too stupid, what is the reason for the video

This is a comparative test, what will be the situation when there is no similar ic to test for confirmation?

thanks. Sometimes, those coils are "shorted" when they are close to a CPU and GPU and the short disapear when we remove the CPU for instance. How do you explain and what to do if the CPU/GPU is soldered?

What is this

It's wrong at all,red lead should put on gnd pin and then put black lead on all the pins.

On opamp and comparator ICs it’s much easier to go to diode mode and put your red lead on ground/negative voltage pin. The use black probe to go to each pin. Most should test from .6xx to 1.3V in circuit. +V and -V pins should read the lowest, around .4xx. If they’re in these ranges it’s good. PWM ICs are different. You should test readings on a known good one. Good luck everyone and enjoy and learn as much as possible. Electronics is a relaxing hobby when you have a good amount of knowledge. It does take 1-2 years to get to that point.

They're both working just fine so.., put your solderin' iron away!

When the multimeter is put in diode mode, what you see in its display is volts, not ohms...

:) What did you do bro :)

Where do you get the schematic?

I believe you're misnaming the pins. #1 is the top right most pin as per your diagram. At 1:35, that is not pin #4, it is #11 etc.

what are you doing ??????????????????

CAN NOT UNDERSTAND YOUR ENGLISH AND VOICE IS MUCH TO LOW !!

جزاك الله كل خير وجعله في ميزان حسناتك

Method is useful but try to do faster from next video...

No need for the music at all

does this method work with squared IC and smd IC ?

thankyou

Absolutely gold of a video. Thanks my friend keep up the good work.

please upload more like this video. thanx

thankyou

thankyou. keep it up

for complete video kzbin.info/www/bejne/gKvJna2jmK2MjpI

for complete video kzbin.info/www/bejne/pYGqYol6fr2EhJI

for complete video go link kzbin.info/www/bejne/b2LReqpnrdeUi5I

for complete video kzbin.info/www/bejne/ppzUhICEfLWMZtk

complete video link kzbin.info/www/bejne/jYOqi4yIlrGrq7s

complete video link kzbin.info/www/bejne/ooKndoGborufl5I

complete video link kzbin.info/www/bejne/rKKndXiGjNFneqM

complete video link kzbin.info/www/bejne/mZbXl41_gayJarM

complete video link kzbin.info/www/bejne/sHuvYZ2Pl7Z3m6M

for complete video go to kzbin.info/www/bejne/an-6YpV8eNR0ia8

for complete video go to link kzbin.info/www/bejne/n56YZKhrd8mciKM

for complete video go to kzbin.info/www/bejne/hnm3mXyPbc92Zsk

Not sure It's a problem on my end, but I see everything stretched vertically

مضحكة

WOW. I can see multiple things wrong with teaching people to remove ic's like this!!

If I want to know which ic might be faulty into pcb without checking by multimeter then how I could do ?

Greetings, I have seen your video several times, I have a very similar nanostation M5, in my case it does not turn on and there are 24 volts at the input and I do not have an adjustable source like the one you use in the video, how can I know if power is reaching the microprocessor or other places, where I can measure.

Sir, your sound is bad..

Thankyou

Hi , please zoom in on the mainboard a little more when you want to take measurement or find short circuit on the mainboard .thnx

Hi there , please upload more about laptop troubleshooting & short circuit finding . thnx

Hi there , at 01:52 , when we have sound or Buzzer on Multimeter that means we have a short or not ? thnx

thankyou , keep it up

Please upload more like this Video . thnx

Hi there , when you are doing to test Mosfet you multimeter is on Diode Mode Right ? thnx

Hi , when we are on Diode Mode and we have sound or Buzzer ,that means we have short , and if you don't have sound or buzzer and we have voltage that means ic working well , right ? thnx

Hi , at 09:19 you Injected voltage in Current Resistor output ?right thnx

Hi there , please upload more like this video . thnx